Harbor Freight Tools 67781 User's Manual
Contents
1. for Harbor Freight Tools FLAT PANEL TV WALL MOUNT ille Ag 6778 INSTRUCTIONS AND PRECAUTIONS Visit our website at http www harborfreight com SAVE THESE INSTRUCTIONS READ ALL PRECAUTIONS AND INSTRUCTIONS Copyright 2010 by Harbor Freight Tools All rights reserved No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this document may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 SPECIFICATIONS Weight Capacity 150 Ib For LED LCD Plasma TVs 37 to 61 wide UNPACKING When unpacking make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at 1 800 444 3353 as soon as possible 1 10 11 12 IMPORTANT SAFETY INFORMATION Do not exceed 150 Ib max weight capacity of TV Bracket Sudden load movement may briefly create excess load causing product failure Do not mount TV Bracket to hollow wall gypsum board or similar material that will not support the weight of the TV Mount only to 2 x 4 wood stud or concrete brick walls that can safely support combined wei2. 1 800 444 3353 Page 4
3. Phillips screwdriver 1 4 drill bit for drilling into wood stud 1 2 masonry drill bit for drilling into brick or concrete wall and minimum 6 level 5mm hex wrench and 10mm combination wrench Before Installing Use the 5mm hex wrench to double check that all four socket screws of the Wall Bracket 1 are tight Tighten any connection if needed 2 Set Wall Bracket against the wall at the desired height Place a level over the upper or lower cross bar and adjust Bracket until level Use a marker to indicate locations of mounting holes Attaching to Wood Studs First verify woods studs are at least 16 apart Use a Stud Finder not included to find two adjacent studs 16 apart Use a marker to indicate locations of the studs 2 Drill four 1 4 holes at least 3 1 2 deep into the studs at the marked spots 3 Use Lag Bolts 10 and Washers 9 to mount Wall Bracket to wall See Figure 1 below Wall vo a Bracket 1 Lag Bolt 10 and Washer 9 Figure 1 Attaching to Brick or Concrete Wall NOTE Verify at least 6 of space are between any two holes Use 1 2 carbide tip masonry drill bit and drill four 3 3 8 deep holes 2 Insert the Wall Anchors 11 into the holes making sure they are flush with the wall surface 3 WARNING Wall Anchors must be set firmly against concrete or masonry If mounting to SKU 67781 For technical questions please call 1 800 444 3353 a m
4. asonry wall covered with drywall plaster counter bore a hole through drywall plaster around mounting holes locations This will allow Wall Anchors to be set directly against concrete or masonry See Figures 2a and 2b below Wall Bracket 1 ee PSs 4 Yh JM 7 AI Concrete Lag Ve Bolt 10 if il Ai A re f pemn rire ao Tait a a eet G A s Pa Pa r r fal Ji 7 ia as Washer i Wall ce 9 ae Anchor 11 Figure 2a Wall EE ee Al a a Pi F Ai Concrete 1 Wd PAN KGI A 7A CA AMIE i taida ma Lag E p E Bolt TH lt 3 GG CN i a i Plaster Wall A Drywall i Anchor 11 Figure 2b 4 Once Wall Anchors are securely set into concrete use Lag Bolts and Washers to install Wall Bracket to wall See Figure 3 below Wall Anchor 12 Wall i Bracket HH 1 ae Lag Bolt 11 and Washer 10 Figure 3 Attaching to Metal Studs or Concrete Block Wall 1 NOTE If mounting to steel stud wall or cinder block wall alternative mounting hardware is required Installing Support Arms to Flat Panel TV 1 WARNING Verify TV is unplugged before threading any Screw into the TV s back panel Page 2 2 3 4 si 6 SKU 67781 WARNING Do no lay flat panel TV face down cover its surface with a towel or other soft material and tilt it against the wall or another solid surface WARNING Some Flat Panel TVs are heavy two people may
5. be needed to lift and support the TV while it is being attached to the TV Bracket Locate the mounting holes on back of TV and select mounting Screws 3 6 that fit properly NOTE If you do not find the appropriate sized Screws refer to TV owners manual or contact TV manufacturer Thread the Screws 3 4 5 or 6 through the Square Pads 8 the Support Arms 2 Spacers 7 and into the mounting holes in the back of TV panel See Figure 4 below Screws 3 6 A zi Square Pad 8 Ei a 3 Spacer 7 Support Arms 2 Figure 4 NOTE The wide part of the Spacers rest against the Support Arms Carry TV to mounted Bracket and lower onto Cross Bars making sure the four tabs of the mounts are hooked onto the top of Cross Bars and that TV is centered See Figure 5 Figure 5 10 For technical questions please call 1 800 444 3353 Angle Adjusting Tighten the two clamping screws leaving about an eight of an inch space See Figure 6 Clamping Screw ON Figure 6 To adjust the TV angle back off the two nuts at the Support Arm hinges by one turn Back off the two angle adjusting screws located at the sides of the Support Arms until end of the screw threads are almost flush with the other side of the Support Arms See Figure 7 Screw Figure 7 CAUTION Make sure that the end of the screws does not come out of the Support Arms Tilt the TV to the desired angle four approx
6. ght of Bracket TV and all attached hardware and components If you are unsure wall is strong enough to support weight of TV and TV Bracket contact a professional installer to reinforce wall Do not mount overhead Assemble and install only according to these instructions Improper assembly and installation can create hazards and lead to personal injury and property damage Verify that mounting surface has no hidden utility lines before drilling or driving screws Wear ANSI approved safety goggles and heavy duty work gloves during installation Inspect before installing do not mount to wall if parts are missing loose or damaged Use as intended only Do not use TV Bracket for any purpose for which it was not designed Keep installation area clean and well lit Do not assemble or install when tired or when under the influence of drugs or medication This product is not a toy Do not allow children to play with or near this item Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement ASSEMBLY AND MOUNTING Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product A NOTE The following tools none supplied are required for mounting and installation Stud Finder 11 16 socket ratchet handle 2
7. imate adjustment positions 0 3 7 and 12 Tighten the Angle adjusting screws all the way to lock the angle position Page 3 PARTS LIST amp ASSEMBLY DIAGRAM Description _ Wall Bracket _ S Wall Bracket T g Bolt 11 Wall Anchor AN ere ai ney wrth mamn i ESN iNT RNR R 3 4 5 6 OR T asa maT 4 A C 3 ay a A pimmee SS kA ae 5 ny 7 8 9 10 11 Record Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 67781 For technical questions please call
Download Pdf Manuals
Related Search