Harbor Freight Tools 6 In. Fractional Dial Caliper Product manual
Contents
1. WARNING or serious injury TACAUTION CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE is used to address practices no TTT ited persona CAUTION CAUTION without the safety alert symbol is used to address practices not related to personal injury SKU 92437 For technical questions please call 1 800 444 3353 Page 2 WARNING Read all instru Failure to follow all instructions listed below may result in serious injury SAVE THESE INSTRUCTIONS WORK AREA SAFETY Keep children and bystanders away while operating Distractions can cause you to lose control Keep work area clean and well lit Cluttered or dark areas invite accidents PERSONAL SAFETY Wear ANSI approved safety goggles and heavy duty work gloves during use and service Stay alert and use common sense when operating Do not use when tired or under the influence of drugs alcohol or medication Do not overreach Keep proper footing and balance at all times This enables better control in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away fram moving parts Loose clothes jewelry or long hair can be caught in maving parts PRODUCT USE AND CARE This Cal er is not a toy Keep it out of reach of childre Use the correct product for your application The corr2. Inside Diameter Figure D 18 To make a step measurement of an object see Figure E To measure the depth of an abject see Figure F Figure F ACAUTION 229041 product can ta causing personal injury Do not Cleaning maintenance and lubrication 1 BEFORE EACH USE inspect the general condition of Caliper Check for loose screws misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation 2 AFTER USE clean external surfaces of the product with clean cloth 3 STORE in carrying case and keep in dry and secure location SKU 92437 For technical questions please call 1 800 444 3353 Page 7 Description ES Thumb Roll Outside Diamater Jaws Dial Adjustment Lock Dial Adjustment Dial Slide Seale Lack Sliding Index Edge Inside Diameter Jaws Step Measuring Surface Depth Measuring Blade 10 c of en 2 eof 10 PLEASE READ THE FOLLOWING CAREFULLY Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 92437 For technical questions please call 1 800 444 3353 Page 8
3. After use wipe off and place in storage case and keep in secure and dry location ut of reach of children The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS SKU 92437 For technical questions please call 1 800 444 3353 Page 4 SPECIFICATIONS Manman Range E Materiais Stainless Stool Scala Type Mechanical Dial Measuring Capabliios inside Outside Dopin T Sep Gatper Accuracy moor UNPACKING When unpacking make sure that item is intact and undamaged If any parts are missing or broken call Harbor Freight Tools at the number on the cover of this manual INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product 0 Read the ENTIRE IMPORTANT SAFETY Please note Calipers with dials can jump a setting Always double check a reading Make sure upper and lower Outside Diameter Jaw 2 faces are clean See Fig A 2 Loosen Slide Scale Lock 6 by tuming it counterclockwise 3 Use Thumb Roll 1 to close Outside Diameter Jaws 2 4 Sliding Index Edge 7 should line up at 0 5 To adjust if needed
4. PITTSBURGH 6 DIAL FRACTIONAL CALIPER SET UP AND OPERATING INSTRUCTIONS Visit our website at http www harborfreight com Read this material before using this product A Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2004 by Harbor Freight Tools Al rights reserved No parton of this manual or any artwork Contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may net be drawn proportionally Due to continuing improve mants actual product may difer siightiy from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year af purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death
5. ect product will do the job better and safer at the rate for which it was designed Do nat modify Caliper or use it for a purpose for which itis not intended Check for binding of moving parts breakage of parts and any other condition that may affect the Caliper s operation If damaged have the Caliper repaired and calibrated before use Use the product and accessories etc in accordance with these instructions and in the manner intended for the particular type of product taking into account the working conditions and the work to be performed Use of the product for opera tions different from those intended could result in a hazardous situation SKU 92437 For technical questions please call 1 800 444 3353 Page 3 SERVICE Have Caliper serviced by a qualified repair person using only identical replace ment parts This will ensure that the safety of the product is maintained Maintain labels and nameplates on the product These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replace ment SPECIFIC SAFETY WARNINGS AND PRECAUTIONS Keep Caliper away from water oll solvents and any other liquids Do not lubricate the Caliper s moving parts Do not exceed the 6 capacity of Caliper Handie carefully the Caliper is a delicate instrument Do not disassemble Caliper Use caution when handling The Caliper has sharp machined edges Do not drop or overtighten during use
6. loosen the Dial Adjustment Lock 3 by turning it counterclockwise 6 Set the Dial 5 by turning the Dial Adjustment 4 either clockwise or counterclockwise until the Dial Needle points to 0 7 Lock the Dial 5 on its 0 setting by tightening the Dial Adjustment Lock 3 clockwise The Caliper is ready to use ma P SKU 92437 For technical questions please call 1 800 444 3353 Page 5 8 Toread the Scale and Dial the Sliding Index Edge 7 features readings in inches 0 001 and 0 010 per call out segment See Figure B below Dial 5 Sliding Tadex Edge 7 9 Read the Scale Measurement Point in inches and tenths of inches such as 0 5 Than read the Dial Needle on the Dial in thousandth of an inch such as 081 10 Combine the two readings for a final reading of 0 581 11 To use the Caliper to measure the outside diameter of an object close the Out side Diameter Jaws 2 over the object making sure that the item rests squarely on the Jaws See Figure C below Make note of the value along the Sliding Index Edge 7 Then read the whole number indicated by the dial arm Finally note the numbers of lines after the whole number For example values 1 5 30 and 3 will read as 1 5 0 030 and 0 003 which equal 1 533 Figure SKU 92437 For technical questions please call 1 800 444 3353 Page 6 12 To use the Caliper to measure the inside diameter of an abject see Figure D below
Download Pdf Manuals
Related Search