Harbor Freight Tools 6/12V Product manual
Contents
1. CEN TECH Model 43700 CIRCUIT TESTER 6V 12V Heavy Duty 3011 349 Visit our Web site at http www harborfreight com Copyright 2000 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may 1 2 To test 6 Volt or 12 Volt fuses wiring or other 6V 12V circuitry connect the Cord Clamp part 13 to one side end of the fuse wire vehicle battery post etc either the positive or negative pole Gently touch and hold the tip of the Probe against the be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions please call 1 800 444 3353 UNPACKING When unpacking check to make sure all parts shown on the back of this instruction flyer are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the front of this manual as soon as possible ASSEMBLY AND O ATING INSTRUCTIONS NOTE All parts below refer to the parts listed on the reverse side of this instruction flyer Remove the rubber protective tip from the Probe part 1 other side end of the component being tested If the Bulb part 5 inside the Handle part 2 illuminates this indicates there is electricity flowing through the circuit No illumination of the Bulb indicates no electricity flowing through the circuit and that repair or replacement of the component being tested is needed2. CLE G AND C To clean remove the Cord Clamp part 13 from all power sources Wipe the outside with a clean damp cloth using a mild soap with water if necessary Then dry Do not immerse this product in any liquids To change the Bulb part 5 unscrew the Probe Base part 7 from the Handle part 2 and remove the Spring part 4 Unscrew the Bulb from the Spring Screw in a new 12 Volt 3 Watt Bulb in the Spring Replace the Spring and Bulb in the Handle and Screw in the Probe Base SEE REVERSE SIDE OF THIS INSTRUCTION FLYER FOR PRODUCT WARNINGS PRECAUTIONS PARTS LIST AND ASSEMBLY DIAGRAM CN a ee ee AFETY WAR ND PRE TION 1 KEEP PRODUCT USAGE AREA CLEAN 7 MAINTENANCE Service and maintenance should Cluttered areas invite injuries be performed regularly by a qualified technician 2 KEEP CHILDREN AWAY FROM PRODUCT 8 USE THE RIGHT PRODUCT FOR THE RIGHT USAGE AREA Do not allow children to handle this JOB There are certain applications for which this product product was designed Use this product ONLY when testing 6 Volt and or 12 Volt electric currents 3 DO NOT USE THIS PRODUCT IF UNDER THE DO NOT use this product for a purpose for which INFLUENCE OF ALCOHOL OR DRUGS Read it was not intended warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs SAVE THIS INSTRUCTION FLYER If there is any doubt do not attempt to use this pr
3. HE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE MENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Item 43700 EEN TECH Circuit lester 6V 12V Heavy Duty A Warning l Read instruction manual before using 2 Always wear ANSI approved safety goggles when working with tools and equipment 3 Caution Use this product ONLY tor testing 6 Volt and 12 Volt electric circuits 4 Never use when on moist surface or When standing water is present Do not remove this Waming label Made in China
4. oduct You will need this instruction flyer for the 4 USE EYE PROTECTION Wear ANSI approved Operating and Maintenance Procedures Safety safety impact eye goggles The ANSI approved safety Warnings and Precautions Parts List and impact goggles are available from Harbor Freight Tools Assembly Diagram Keep your invoice with this instruction flyer Write the invoice number on the 5 CHECK FOR DAMAGED PARTS Before using the front of this fiyer Keep this instruction flyer this product carefully check that it will operate properly and invoice in a safe and dry place for future and perform its intended function Check for damaged reference parts and any other conditions that may affect its operation Replace or repair damaged or worn parts NOTE Some parts are listed and shown for illustration immediately purposes only and are not available individually as replacement parts 6 REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Only use accessories intended for use with this product Approved accessories are available from Harbor Freight Tools PARTS LIST ASSEMBLY DIAGRAM PART DESCRIPTION i Cord Clamp LEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR S
Download Pdf Manuals
Related Search