Harbor Freight Tools 46407 User's Manual
Contents
1. 46407 Page 2 plications for which this Lathe Stand was designed Do not modify this Lathe Stand and do not use this tool for a purpose for which it was not intended 11 Stay alert Watch what you are doing use common sense Do not use any Lathe Stand when you are tired 12 Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate prop erly and perform its intended function Any part that is damaged should be properly repaired or replaced by a qualified technician 13 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty 14 Do not use Lathe with Stand if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or re flexes are impaired while taking drugs If there is any doubt do not use the Lathe with Stand 15 Take caution as some woods contain preservatives such as copper chromium arsenate CCA which can be toxic When cutting these materi als extra care should be taken to avoid inhalation and minimize skin contact 16 Maintenance For your safety maintenance should be performed regularly by a qualified technician Warning The warnings cautions and instructions discussed in this instruc tion manual cannot cover all possible conditions and situations that may oc cur It must be understood by the operator tha2. flat level surface so that the insides of both leg structures are facing each other Line up the two holes on a Leg Mounting B 6 with the holes on the inside of one of the Legs A amp B 3 amp 4 Secure it with two sets of Bolts 7 Spring Washers 9 Flat Washers 8 and Nuts 10 Take the other end of the Leg Mounting B 6 bracket and attach it to the inside of the corresponding Leg A amp B 3 amp 4 on the other leg structure using two sets of Bolts 7 Spring Washers 9 Flat Washers 8 and Nuts 10 Repeat the same procedure on the other two Legs A amp B 3 amp 4 Stand up the unit Lastly attach an Adapter Plate 1 to each Base Plate 2 using four sets of Bolts 7 Spring Washers 9 Flat Washers 8 and Nuts 10 The stand is ready for your lathe Operation Note Always use the stand on a flat level dry surface We recommend us 1 2 ing two people to secure the lathe to the Lathe Stand When mounting a lathe onto the stand first make sure the mounting holes on the stand correspond with the mounting holes on the lathe One person should hold the lathe so that the mounting holes line up while the other person puts one of the bolt washer nut combinations not includ ed through one of the holes in an Adapter Plate 1 and tighten by hand Next attach one bolt washer nut combinations not included through one of the holes on the other Adapter Plate 1 Tighten by hand Now add the remaining
3. CENTRAL MACHINERY WOOD LATHE STAND VELGI 46407 SET UP AND OPERATING INSTRUCTIONS Designed for Harbor Freight Tools Wood Lathe 36066 Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Failure to do so can result in serious injury Read this material before using this product SAVE THIS MANUAL Copyright 2001 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 Cover revised 07i Specifications Overall Dimensions 56 L x 18 W x 31 1 8 H Base Mounting Holes 4 39 holes 8 1 2 apart from center Leg Distance 49 x 15 with 31 mounting holes on each leg Weight 21 Ib Save This Manual You will need the manual for the safety warnings and precautions assembly in structions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Saf
4. ety Warnings and Precautions WARNING When using tool basic safety precautions should always be fol lowed to reduce the risk of personal injury and damage to equipment Read all instructions before using this product ale 2 3 10 Avoid working alone If an accident happens an assistant can bring help Keep work area clean Cluttered areas invite injuries Observe work area conditions Don t expose to rain Keep work area well lighted Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords Store idle equipment When not in use tools must be stored in a dry loca tion to inhibit rust Always lock up tools and keep out of reach of children Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair Use eye and ear protection Always wear ANSI approved impact safety goggles Do not overreach Keep proper footing and balance at all times Do not reach over or across electrical cables or frames Maintain tools with care Inspect Lathe Stand periodically and if damaged have it repaired by an authorized technician Use the right Lathe Stand for the job Do not attempt to force a small Lathe Stand to do the work of a larger industrial tool There are certain ap SKU
5. hardware not included to secure all of the mount ing holes and tighten with a wrench SKU 46407 Page 4 Maintenance 1 Clean dirt grease or wood chippings off of the stand with a cloth or brush 2 Periodically tighten all of the hardware Parts List Part Description Qty 7 10 6 LegMounting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ome parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 46407 REV 02B Page 5 a _ Assembly Drawing SKU 46407 Page 6
6. t common sense and caution are factors which cannot be built into this product but must be supplied by the operator Warning Read and follow all of the warnings that came with the Lathe that you use with this stand Unpacking When unpacking check to make sure the parts listed on page 5 are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual SKU 46407 Page 3 Assembly Refer to the Assembly Drawing on page 6 Note The only tool necessary is an adjustable wrench It is advised to always po tighten hardware by hand until the unit is complete then tighten with the wrench Take a Base Plate 2 and attach a Leg A 3 to one side of it using four sets of Bolts 7 Spring Washers 9 Flat Washers 8 and Nuts 10 On the opposite side of the Base Plate 2 attach a Leg B 4 using a set of Bolts 7 Spring Washers 9 Flat Washers 8 and Nuts 10 Repeat this procedure with the other Base Plate 2 and Legs A amp B 3 amp 4 so that you have two identical leg structures In the lowest holes of both Legs A amp B 3 amp 4 on one leg structure attach a Leg Mounting A 5 so that the holes match up and the angled lip is on top Secure with two sets of Bolts 7 Spring Washers 9 Flat Washers 8 and Nuts 10 Repeat same procedure with the other leg structure Next you will join the two leg structures allowing the unit to stand Lay the units on a
Download Pdf Manuals
Related Search