Harbor Freight Tools 45 Watt Solar Panel Kit Product manual
Contents
1. BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Assembly Diagram SKU 90599 45w solar power kit Part No Description Part No Description 1 Syphon pipe 11 Back plastic frame 2 Top connection pipe 12 Front plastic frame 3 3 holes pipe 13 Solar panel fix screws 4 3 holes pipe 14 Solar cell 5 Middle connection pipe 15 3 in 1 connection cable 6 Connection pipe right side 16 Charge regulator 7 Support leg 17 Battery clamp 8 Bottom pipe 18 12VDC light 9 Fix screws 19 Multi purpose cable 10 Srew nut 20 Extension cable Page 10 For technical questions please call 1 800 444 3353 SKU 68751 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons o2. be sure that all accessory cables reach their connection points without placing any stress on the wiring 2 Angle face of Solar Panel Frame toward true south1 according to chart that follows Latitude Solar Panel Angle 0 4 10 5 20 Latitude 5 21 45 Latitude 10 46 64 Latitude 15 65 or more 80 1 Angle towards true north if installed in southern hemisphere Solar Panel Frame Assembly 1 First attach all the components of the frame together See Figure 1 below NOTE Do not fasten connections with hardware yet Figure 1 Mounting Holes Mounting Holes IMPORTANT During assembly make sure that the solar panel mounting holes along the Top Tubes 2 and Bottom Tubes 8 face OUT from the frame assembly See Figure 1 above 2 Attach Corner Connectors 1 to Side Tubes 6 Then use the Fixed Screws 9 and Nuts 10 to fasten the Corner Connectors to the Top Tube See Figure 2 below Figure 2 Fixed Screw 9 Nut 10 Corner Connector 1 Side Tube 6 Top Tube 2 3 Use Fixed Screws and Nuts to fasten the Top Tubes to the Leg Connectors 3 and then the Support Legs 7 to Leg Connectors See Figure 3 following Page 5 For technical questions please call 1 800 444 3353 SKU 68751 Figure 3 Fixed Screw 9 Top Tube 2 Leg Connector 3 Support Legs 7 NOTE There are two possible settings for the Leg Connectors to allow for diff
3. positive See Figure 6 below Charge Controller 16 Battery Terminals Fuse Figure 6 9 Connect Splitter Cable to Extension Cable 20 and then to the Charge Controller See Figure 7 below Figure 7 Extension Cable 20 Splitter Cable 15 Page 6 For technical questions please call 1 800 444 3353 SKU 68751 Wiring Note Only a licensed electrician and a licensed building contractor can safely design and implement a grid tie in system Any grid tie in system must meet all applicable building and electrical codes and must meet standards established by the area power company 1 Run wires from panels through weatherproof grommets and into enclosure where charge controller regulator is located Use wires of the proper size and rating and use twist connectors not included to connect wires 2 Connect to Charge Controller according to Controller s instructions 3 Secure all connections using terminals or solder all wire splices to ensure good connections 4 Weatherproof all connections and route the wire in a way that it will not be torn loose from the panel Operation Note Performance of the Solar Panels will vary dependent on site location angle of the panels in relation to the arc of the sun and available sunlight Recharging a Battery 1 To recharge a 12 volt battery not included while paying attention to the proper polarity black is negative and red is positiv
4. 45 Watt Solar Panel Kit 68751 Solar Panel Kit Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Visit our website at http www harborfreight com Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Email our tech support at tech harborfreight com Page 2 For technical questions please call 1 800 444 3353 SKU 68751 IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates a hazardous situation which if not avoided will result in death or serious injury WARNING indicates a hazardous situation which if not avoided could result in death or serious injury CAUTION used
5. 68751 Specifications Rated Output 14 5 V 15 W per solar panel Open Circuit Voltage 23 5 OCV Adapter Outlets 3 6 and 12 VDC Note Output will decrease as the panel gets hotter than room temperature 70 F Angle solar intensity cloud cover and other factors will effect output Installation IMPORTANT Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Location 1 Locate the Solar Panels 14 where they will receive full unobstructed sunlight especially during midday Nearby trees or tall plants will drop debris requiring the panels to be cleaned more frequently 2 The setup location for the Solar Panel Kit must be inaccessible to children to prevent electric shock Build a childproof enclosure if needed 3 Install the charge controller regulator and batteries in a weatherproof enclosure with proper ventilation Mounting 1 Select a mounting location for the Solar Panel Kit The Solar Panels should face the Sun and not be blocked by shadows The location should allow the Panels to be protected from accidental damage The location should be flat stable and able to support the weight of the Solar Panel Kit s accessories Before assembly
6. 8 16 11 12 16 14 15 14 12 18 18 16 20 14 12 10 22 24 12 30 16 14 10 40 12 10 8 50 14 100 12 10 6 4 150 10 8 4 2 200 8 6 Minimum Wire Gauge 11 Install an appropriate charge controller regulator to regulate output and prevent damage Do not attach panel to battery or power grid without proper regulator inverter and or charge controller 12 Install and use according to applicable National Electrical Code NEC standards 13 This panel is not rated for use as fire resistant roofing If installing on a roof install only over a fire resistant roof covering rated for the application 14 Verify that installation surface has no hidden utility lines before drilling or driving screws 15 Install only according to these instructions Improper installation can create hazards 16 Wear ANSI approved safety goggles and heavy duty work gloves during installation Do not wear jewelry or metal watches when working near solar panels wiring or batteries 17 Handle panel with care Glass may break or a sharp edge may be exposed during movement 18 Keep installation area clean and well lit 19 Install out of reach of children 20 Keep bystanders out of the area during installation 21 Do not install when tired or when under the influence of drugs or medication 22 Use in 12 VDC systems only Battery Precautions 1 Wear splash resistant ANSI approved sa
7. all keep the angle recommended on page 4 Page 8 For technical questions please call 1 800 444 3353 SKU 68751 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Parts List Part Description Qty 1 Corner Connector 4 2 Top Tube 2 3 Leg Connector 2 4 Tube Connector 2 5 Middle Tube 1 6 Side Tube 2 7 Support Leg 2 8 Bottom Tube 2 9 Fixed Screws 12 10 Nut 24 Part Description Qty 11 Back Frame 3 12 Front Frame 3 13 Panel Screws 12 14 Solar Panel 3 15 3 In 1 Splitter Cable 1 16 Charge Controller 1 17 Battery Clamp Cable 1 18 Lighter Cable 1 19 Multi Adapter 1 20 Extension Cable 1 Page 9 For technical questions please call 1 800 444 3353 SKU 68751 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
8. and off the lights press the switch on the outside of each light socket NOTE You may plug in the each light into to either 12V DC outlet Note This system can also be used to power other small 3V and 6V DC small appliances 9 Plug the appropriate plug on the Multi Adapter into the appliance The adapter has 3 6 and 12 Volt DC plugs 10 Insert the plug on the other end of the wire attached to the Multi Purpose Adapter into the appropriate DC Outlet on the Charge Controller 11 Activate your appliance CAUTION Only on appliance can be used at a time with this adapter and the adapter must be plugged into the same voltage output 12 When finished unplug the Multi Adapter wire plug from the Charge Controller and then unplug the Multi Adapter from the appliance 13 To charge cell phone or other small electronic item plug the item s power cored into the USB Port on the front of the Charger Controller See Figure 9 14 Use the Inverter Output and the 12V Female Output ports to connect the male adapters for 12V accessory items that need to be charged See Figure 9 above Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT SERIOUS INJURY FROM ELECTRIC SHOCK Before service maintenance or cleaning a Dry solar panels and outdoor wiring thoroughly while wearing electrically insulated gloves b Cover solar panels with an opaqu
9. e connect the two ring terminals on the Battery Clamp to the Battery Terminals on the back of the Charge Controller See Figure 8 below 2 Connect the black clamp to the black or negative terminal on the battery not included Finally connect the red clamp to the red or positive terminal on the battery Avoid accidental contact of the red and black battery clamps to each other 3 Turn on the Charge Controller See the On Off switch in Figure 8 below Initially charge for three days Figure 8 On OFF Switch USB Output Digital Voltage Meter 12V Female Output Female Inverter Output Overload Discharge Indicator Digital Voltage Meter Switch 4 Never leave the battery not included unattended while charging When battery is fully charged the reading on voltage display will show 13 or above NOTE The voltage display will have to be turned on in order to monitor the battery voltage Press the Voltage Meter Switch to turn off the Voltage Meter when not monitoring the battery voltage since it consumes energy Twelve 12 Volt batteries should charge to 13 Volts for a full charge To stop charging the battery turn Power Switch to OFF and disconnect the solar panels from the Charge Controller NOTE The Charge Controller provides overcharge protection If the battery voltage is higher than 14 5 V the regulator will shut off charge from solar panel 5 The Charge Controller provides t
10. e cover c Disconnect all solar panels and batteries TO PREVENT SERIOUS INJURY FROM ELECTRIC SHOCK OR CUTS Do not use damaged solar panel If wiring insulation is damaged or weathered glass is cracked or housing is opened have the problem corrected before further use Note It is normal to see up to 20 degradation in amorphous silicon solar panel performance within the first 6 months before the amorphous coating stabilizes Cleaning Clean and inspect the Solar Kit system MONTHLY or more frequently to maintain peak efficiency 1 Wear electrically insulated gloves and ANSI approved safety goggles Dry solar panels and outdoor wiring thoroughly 2 Cover solar panels with opaque cover 3 Disconnect all solar panels and batteries 4 Clean solar panels one at a time with mild non abrasive cleanser and soft cloth and paper towels Do not clean with brushes or abrasive cleaners 5 Inspect general condition of Solar Kit system panels batteries controllers and mounting Check for loose hardware wiring insulation damage or weathering cracked glass open housing cracked or broken parts loose or corroded contacts and any other condition that may affect its safe operation 6 Maintain batteries according to supplier s instructions Adjustment To increase efficiency 1 In the Winter increase the panels angle by 10 2 In the Summer decrease the angle by up to 10 3 In Spring and F
11. e in to a grid Only a licensed electrician and a licensed building contractor can safely design and implement a grid tie in system Any grid tie in system must meet all applicable building and electrical codes and must meet standards established by the area power company Improper grid tie in can result in electrocution fire and other serious personal injury and property damage An incorrectly installed grid tie in system can cause feedback voltage resulting in electrocution of electrical utility workers 5 Do not stand on or otherwise apply pressure to panel 6 Handle solar panel with care edges may be sharp 7 Do not focus light on panel 8 Install components with enough space to allow proper cooling 9 This product may occasionally produce more current and or voltage than its rated output Increase output ratings by 25 when determining component required voltage and amperage ratings Refer to Section 690 8 of the National Electrical Code for an additional multiplying factor of 125 percent 80 percent derating which may apply Page 3 For technical questions please call 1 800 444 3353 SKU 68751 10 Panel must be connected using UL listed outdoor rated wire of the correct thickness gauge for the amperage rating and length see warning number 9 also Follow the guidelines in the chart below Current in Amps Maximum Length 5 10 15 20 25 0 5 18 6 7 18 16 8 18 16 10 1
12. erent angles facing the sun Before securing Leg Supports in place be sure to adjust Leg Connectors so that both Connectors are set at the same angles This will help keep the frame balanced 4 Verify all connections are tightened and that the frame is secure WARNING Do not install the Solar Panels until the frame is properly assembled and balanced on surface 5 Determine where you want to position the frame assembly making sure it is facing south for maximum sun exposure with no obstructions in front of it The Charge Controller 16 must be in a dry well ventilated location nearby If necessary build a small structure that guarantees the unit will stay dry during rain or snow and provide enough ventilation to allow the unit to vent and cool properly 6 Set the Solar Panels onto the frame assembly aligning the Panels mounting holes with the mounting holes on the Top and Bottom Tubes Use the Panel Screws 12 and Nuts to secure the Solar Panels to the frame assembly See Figure 4 below Figure 4 Panel Screw 12 7 Connect end of lead wires coming from Solar Panels 14 to the Splitter Cable 15 See Figure 5 below Figure 5 Splitter Cable 15 8 Connect the ends of the Battery Clamps to the battery terminals on the back of the Charge Controller Then attach the Battery Clamps to the battery s terminals WARNING Be sure to connect all matching polarities Black is negative and red is
13. fety goggles and electrically insulated gloves while working near batteries 2 Use an appropriate charge controller whenever connected to battery 3 Charge store and maintain batteries according to supplier s instructions Service Precautions 1 Before service maintenance or cleaning a Dry solar panels and outdoor wiring thoroughly while wearing electrically insulated gloves b Cover all solar panels with an opaque cover such as a blanket c Disconnect all solar panels d Disconnect all batteries 2 Do not service during rain fog or any other wet humid weather 3 Do not stand on or otherwise apply pressure to panel 4 Do not allow children to play with or near this item or electrical components 5 Inspect at least monthly do not use if damaged parts are loose water is found inside the housing electrical insulation is cracked or damaged or connections are loose 6 Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement 7 WARNING Handling the cord on this product will expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling California Health amp Safety Code 25249 5 et seq SAVE THESE INSTRUCTIONS Page 4 For technical questions please call 1 800 444 3353 SKU
14. he following protection while charging a Over discharge Protection When the electricity level of the battery goes too low below 11 volts from product usage the Charge Controller will automatically shut off the power output to prevent damage to the battery If this occurs stop using the battery and charge it until the Voltage display shows 13 volts b Overcharge Protection If the electricity level on the battery goes too high above 14 5 volts the Charge Controller will automatically shut off power input to prevent damage to the battery c Overload Protection If the output current exceeds 4 amps the fuse see Figure 6 will blow to prevent damage to the controller in the Charge Controller If this occurs have a qualified service technician replace the fuse Note The On Off switch of the Charge Controller must be in the On position to activate the three protection functions mentioned above Using 12 Volt Lights and Accessories Note The Charge Controller must be in ON position at all times 6 If the 12V Lights 18 aren t already attached to the sockets on the end of each light wire gently snap them in 7 Plug the other end of the 12V Light s wire into either of the 12 Volt DC outlets on the Charge Controller as shown in Figure 9 below Page 7 For technical questions please call 1 800 444 3353 SKU 68751 12V DC Outlets 3V DC Outlet 6V DC Outlet Figure 9 8 To turn on
15. r property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
16. with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE is used to address practices not related to personal injury CAUTION without the safety alert symbol is used to address practices not related to personal injury WARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Installation Precautions 1 Exercise special caution if working on roof or another high location Keep proper footing and balance at all times Follow ladder supplier s precautions whenever working near or on a ladder 2 Install all sensitive electrical components including wiring connections regulator and battery inside a weatherproof enclosure to prevent electric shock 3 Do not wire multiple panels in series If you need to connect two or more solar panels together this work must be done by a qualified electrician unless they are connected through a regulator 4 This solar panel kit is not designed for ti
Download Pdf Manuals
Related Search