Harbor Freight Tools 42 in. Off_Road Farm Jack Product manual
Contents
1. bolt or cause the Jack to fail 6 Insert additional supports to make sure the load is properly supported at the lift point to prevent shifting Reversing Latch 11 Reversing Lever 10 Lifting Arm 1 Figure A Reversing Lever in Up Position PITTSBURGH For technical questions please call 1 800 1 888 866 5797 Item 60668 Lowering a Load 1 Place the Handle 4 in the upright position and remove the 1 2 safety bolt placed through the Steel Rail 2 before tripping the Reversing Lever 10 to lower the load Note To lower loads one raised level at a time the Jack must be loaded with 110 Ib 50 kg or more Otherwise the Lifting Arm 1 will drop when the Reversing Lever is placed in the down position 2 Place the Reversing Lever in the down position See Figure B 3 Slowly pump the Handle to lower the load Continue pumping the Handle until the load rests on the ground 4 Clean then store the tool indoors out of children s reach Steel Rail 2 Reversing Latch 11 Reversing Lever 10 Figure B Reversing Lever in Down Position User Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise occurs have the problem corrected before further use TO PREVENT SERIOUS INJURY Remove load from2. Capacity 7000 Ib Maximum Lift Height Lifting Arm 4 1 2 x 1 1 2 Minimum Lift Height WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol Itis used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury Indicates a hazardous situation which if not avoided AWARNING could result in death or serious injury Indicates a hazardous situation which if not avoided ACAUTION could result in minor or moderate injury NOTICE CAUTION IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Save all warnings and instructions for future reference Failure to heed these markings may result in personal injury and or property damage Addresses practices not related to personal injury 1 Study understand and follow all instructions 11 Do not alter the jack or use attachments and before operating this device or adapters that are not supplied by the 2 Donot exceed 7000 Ib rated capacity manufacturer Any alterations or modifications to this tool may result in dangerous conditions 3 Use only on hard flat level surfaces f 3 me Re 12 Be aware of dynamic loading 4 Lifting device only Immediately after lifting Sudden load movement may briefly create support the vehicle with appropriate means excess load causin
3. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference P T TISB UR G H ITEM 60668 FARM JACK J e a J a e a a e a en J j ae z ic p Q e Visit our website at http www harborfreight com REV 14e Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 888 866 5797 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Specifications Weight
4. REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Parts List Part Description Qty 6 RClip tt Part __ s Description _ _ Qty 8 Screw tt 9 Washer tC Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PITTSBURGH Page 6 For technical questions please call 1 800 1 888 866 5797 Item 60668 Assembly Diagram N N Item 60668 For technical questions please call 1 800 1 888 866 5797 Page 7 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitati
5. g product failure 5 Wear ANSI approved safety goggles and 13 Maintain labels and nameplates on the tool heavy duty work gloves during use These carry important safety information 6 Keep clear of load while lifting and lowering If unreadable or missing contact 7 Lower load slowly in controlled fashion Harber EENE odie ora placement Do not allow load to drop quickly 14 This product is not a toy Keep it out of reach of children 8 Do not use for aircraft purposes 9 WARNING This product contains lead a chemical 15 The wamings precautions and instructions discussed in this manual cannot cover all and birth defects or other reproductive harm possible conditions and situations that may occur The operator must understand that common sense California Health amp Safety Code 25249 5 et seq i ane and caution are factors which cannot be built into 10 Inspect before every use this product but must be supplied by the operator do not use if parts loose or damaged A SAVE THESE INSTRUCTIONS known to the State of California to cause cancer Page 2 For technical questions please call 1 800 1 888 866 5797 Item 60668 Steel Rail eeeee0ee5e0e0ee ees 8 Reversing Latch Reversing Lever Handle lt e r e e a e m ea 6 gt Item 60668 For technical questions please call 1 800 1 888 866 5797 Page 3 A Read ENTIRE IMPORTANT SAFETY INFORMATION section at beginning of this manua
6. l including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to Parts List and Diagram on page 6 Lifting a Load 1 Place the Jack on a stable area to prevent shifting or slipping With the Reversing Lever 10 in the down position move the Lifting Arm 1 to the desired position on the Steel Rail 2 and place the Lifting Arm completely under the object to be lifted Note When the Reversing Lever is in the down position and there is no load on the Jack the ratcheting mechanism allows the Lifting Arm to move freely up or down on the Steel Rail 3 To raise the load pull up on the Reversing Page 4 Lever until the notch on the Lever engages the protrusion on the Reversing Latch 11 locking it in the up position See Figure A Slowly pump the Handle 4 to raise the load Always keep a firm grip on the Handle while operating the Jack After the load is raised to the desired height insert a Grade 5 1 2 bolt sold separately through the hole in the Steel Rail immediately below the lifting mechanism as a safety precaution WARNING Dynamic loading may under certain circumstances create a situation where the actual weight being held or lifted is far in excess of Jack or bolt capacity DO NOT drop weight onto the Lifting Arm or allow sudden motion of the Lifting Arm as this may shear the 1 2
7. on of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
8. the jack before any procedure on this page 1 BEFORE EACH USE inspect the general condition of the equipment Check for e loose hardware misalignment or binding of moving parts e cracked or broken parts any other condition that may affect its safe operation 2 Before each use and after the inspection thoroughly test the Jack for proper operation prior to its actual use PERIODICALLY lubricate moving parts of the Jack with lubricating oil The front and back of the Steel Rail must be kept rust free AFTER USE clean the tool with clean cloth Store the Jack in a safe dry location out of reach of children and other non authorized people PITTSBURGH Item 60668 For technical questions please call 1 800 1 888 866 5797 Page 5 Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
Download Pdf Manuals
Related Search