Harbor Freight Tools 40728 User's Manual
Contents
1. Watch what vou are doing Do not operate any machinery when you are tired 15 DO NOT OPERATE MACHINERY WHILE UNDER THE INFLUENCE OF ALCOHOL DRUGS OR PRESCRIPTION MEDICINES 16 CHECK FOR DAMAGED PARTS Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any switch does not turn on and off properly 17 REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Use of any other parts will void the warranty Only use parts and accessories intended for use with this tool which are available from Harbor Freight Tools SPECIAL WARNINGS WHEN USING THIS VISE Csing this Vise may create special hazards dake particular care to safeguard yourself and those around you Electrical Safety Never operate any tool if there is an electrical hazard Never operate an electrical tool in wet conditions Never operate a tool with an improper electrical cord or extension cord Never operate an electrical tool unless vou are plugged into a properly grounded outlet which supplies 110 120Volis We recommend you only use a circuit which is protected by a 30 amp circuit break2. manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator ooo N eg ee ee ee ee ee ee ee ed Page 2 SKU 7 40728 SAFETY WARNING amp CAUTIONS WARNING When using shop equipment basic safety precautions should always be followed to reduce the risk of personal injury and hazards READ ALL INSTRUCTIONS BEFORE USING THIS TOOL 1 KEEP WORK AREA CLEAN Cluttered areas invite injuries 2 OBSERVE WORK AREA CONDITIONS Do not use tools in damp wet or poorly lit locations Don t expose to rain Keep work area well lit Do not use electrically powered equipment in the presence of flammable gases or liquids 3 KEEP CHILDREN AWAY Children must never be allowed in the work area Do not let them handle machines tools or equipment 4 STORE IDLE EQUIPMENT When not in use tools must be locked up in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 DO NOT FORCE THE TOOL It will do the job better and more safely at the rate for which it was intended Do not use inappropriate attachments in an attempt to exceed the tool s capacities 6 USE THE RIGHT TOOL FOR THE JOB Do not use a tool for a purpose for which it was not intended 7 DRESS PROPERLY Do not wear loose clothing or jewelry as they can be caught in movi
3. CENTRAL FORGE 3 Heavy Duty Bench Vise Model 40728 Assembly amp Operating Instructions nee AMER LETT BN ers Distributed Exclusively by 3491 Mission Oaks Blvd Camarillo CA 93011 www HarborFreight com Copyright 1999 by Ilarbor Freight Tools All Rights Reserved No portion of this manual or any artwork contained herein may be reproduced in any manner shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 SPECIFICATIONS MODEL 40728 BENCH VISE Jaw Width z Throat Depth 167 Maximum Jaw Opening Base Dimensions Base Swivel Capacity Anvil Dimensions 4 3 87 x 4 3 8 Overall Dimensions 15 1 27 x 8 x 7 FEATURES OF THIS VISE l Strong cast iron construction with hardened and ground jaws ad Swivel Base with lever locks 3 Work at any angle to the bench 4 Builtin anvil D Enclosed screw for maintenance free operation SAVE THIS MANUAL You will need this manual for the safety warnings and cautions assembly instructions operating procedures maintenance procedures trouble shooting parts list and diagram Keep vour invoice with this manual Write the invoice number on the inside of the front cover Keep both this manual and your invoice in a safe dry place for future reference NOTICE The Warnings Cautions and Instructions disenssed in this instruction
4. OR DISTRIBUTOR EXPRESSLY STATES THATALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO i re AN OE DEE Page 5 SKU 40728 MODEL 40728 BENCH VISE gt MODEL 40728 BENCH VISE PARTS LIST Part Description Part Description l Base 8 C S K Serews 2 Swivel Lever 9 Main Spindle 3 Square Nut 10 Handle 4 Washer 1 Washer 5 Mouth 12 Split Pin 6 Moving Slide 13 Spring 7 Carbon Steel Jaws E Spindle Nut eee Page 6 SKU 40728
5. er or other amperage recommended by the manufacturer Crushing and Marring Overtightening or using incorrect or dirty jaws can cause damage to your workpiece Betore clamping anything in this vise assure that the jaws are clean If the workpiece is softer than steel use soft jaws or shims of softer material to prevent damage to the workpiece Hammering Use caution when hammering anything in or on this vise Preferably use the ground anvil on tap of the Vise as a hammering surface Do not hammer on the outer movable vise jaw as this can damage the screw Use only light hammers on relatively soft material For heavier hammering use an anvil designed for the purpose Slipping Periodically check to be sure the workpiece is tight in the Vise Twisting bending hammering and sawing on a workpiece can cause it to become loose in the vise potentially creating a hazard NOTICE No list of warnings can be all inclusive The operator must supply common sense and operate this tool in a safe manner Page 4 SKU 40728 ASSEMBLY AND OPERATION Your 40728 Vise is delivered completely assembled n Installation 1 Select a sturdy level work bench to install the Vise Be sure there is sufficient room around the vise to hold the various workpieces vou will work on and the various tools vou will use 2 Place the Vise on the work bench where it will be installed a Mark dugugh the holes on the let and right sides of tie base of the Vise
6. ng parts Non skid footwear is recommended Wear restrictive hair covering to contain long hair Always wear appropriate work clothing 8 USE EYE EAR AND BREATHING PROTECTION Always wear ANSI approved impact safety goggles if vou are producing metal filings or wood chips Wear an ANSI approved dust mask or respirator when working around metal wood and chemical dusts and mists Use ANSI approved ear protection when working in a loud or noisy environment 9 DO NOT ABUSE THE POWER CORD When using power tools protect the power cord from damage either from impacts pulling or corrosive materials Do not yank machine s cord to disconnect it from the receptacle 10 DO NOT OVERREACH Keep proper footing and balance at all times Do not reach over or across running machines 11 MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect power cord periodically and if damaged have it repaired by an authorized technician Control handle and power switch must be kept clean dry and free from oil and grease at all times Page 3 SKU 40728 12 REMOVE ADJUSTING KEYS AND WRENCHES Be sure that keys and adjusting wrenches are removed from the toal or machine work surface before operation 13 AVOID UNINTENTIONAL STARTING When using power tools be sure that vou are prepared to begin work before turning the start switch on 14 STAY ALERT
7. onlo the work bench surface Remove the Vise 4 Drill holes through the bench top in an appropriate size J Replace the Vise and insert appropriate size bolts through the Vise base and work bench top 6 Install washers and nuts on the bolts underneath the workbench Tighten securely To Swivel Base l Loosen the Swivel Lever 2 on the base of the Vise by rotating it counterclockwise Swivel the Vise to the position desired 2 Tighten the lever by rotating it clockwise Tu Open and Close Jaws ss Rotate the Handle 10 counterclockwise to open the jaws 2 Rotate the Handle clockwise to tighten the jaws Clamping l Select the standard jaws when clamping flat pieces which will not be damaged by being clamped 2 For flat items which may be marred by the standard jaws either use soft jaws or use a shim between the standard jaws and the workpiece oF Do not overtighten if the workpiece can be crushed or marred by the vise 4 Check the tightness of the workpiece periodically while working on it to prevent slipping PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NETHER THE MANUFACTURER NOR DIS TRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANU FACTURER A ND
Download Pdf Manuals
Related Search