Harbor Freight Tools 3/8 in. x 25 ft. Premium Retractable Air Hose Reel Product manual
Contents
1. 1 The warnings and precautions discussed in this 3 Install an in line shutoff valve to allow manual cannot cover all possible conditions and immediate control over the air supply in an situations that may occur It must be understood emergency even if a hose is ruptured by the operator that common sense and caution are factors which cannot be built into this 4 WARNING The brass components of product but must be supplied by the operator this product contain lead a chemical known to the State of California to cause 2 Obey the manual for the air tool and air birth defects or other reproductive harm compressor used with this tool California Health amp Safety code 25249 5 et seq A SAVE THESE INSTRUCTIONS Item 69234 For technical questions please call 1 800 444 3353 Page 3 Functional Description Specifications Hose Length 25 250 PSI Air Inlet 1 4 18 NPT Components and Controls Guide Roller Bracket L Hose Stopper Mounting Plate Inlet from Compressor Support Post 3 Outlet to tool Reel Drum Figure A Initial Hose Reel Setup Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Repositioning Bracket 1 Remove the Bol2. other condition that affects the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools There is a risk of bursting if the tool is damaged SAFETY Service 1 Tool service must be performed only 3 Use only the lubricants supplied with the by qualified repair personnel tool or specified by the manufacturer 2 When servicing a tool use only identical replacement parts Use only authorized parts Air Source 1 Never connect to an air source thatis 2 Never use oxygen carbon dioxide combustible capable of exceeding 200 psi gases or any bottled gas as an air source Over pressurizing the tool may cause for the tool Such gases are capable of bursting abnormal operation breakage explosion and serious injury to persons of the tool or serious injury to persons Use only clean dry regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air pressure range Safety Symbol Definitions Symbol Property or statement Property or statement WARNING marking concerning Pounds per square inch of pressure Risk of Respiratory Injury Wear WARNING marking concerning WARNING marking Risk of Explosion concerning Risk of Eye Injury Wear ANSI approved eye protection Specific Safety Instructions
3. to persons as a result of being caught in moving parts Tool Use and Care 1 Do not force the tool Use the correct tool for the application The correct tool will do the job better and safer at the rate for which the tool is designed Page 2 For technical questions please call 1 800 444 3353 Keep bystanders children and visitors away while operating the tool Distractions are able to result in the loss of control of the tool Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations Use safety equipment A dust mask non skid safety shoes and a hard hat must be used for the applicable conditions Always wear eye protection Wear ANSI approved safety goggles Disconnect the tool from the air source before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool unintentionally Item 69234 Tool Use and Care cont 3 Store the tool when it is idle out of reach 5 Use only accessories that are identified by the of children and other untrained persons manufacturer for the specific tool model Use of A tool is dangerous in the hands of untrained users an accessory not intended for use with the specific tool model increases the risk of injury to persons 4 Check for misalignment or binding of moving parts breakage of parts and any
4. HNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO CENTRAL 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
5. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference CENTRALPNEUMATIC Retractable Hose Reel With 25ft Air Hose Visit our website at http Awww harborfreight com ITEM 69234 Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2012 by Harbor Freight Tools All rights reserved i E i No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety me
6. decrease tension unwrap the hose one time from the drum General Operating Instructions 1 Check the Wheel operation by slowly pulling the 4 Attach a coupler sold separately to your Hose out You should hear a clicking noise air compressor hose and apply thread S seal tape to the Inlet fitting on the Reel 2 To lock the Hose pull it out a minimum Connect the coupler to the Inlet fitting of 1 2 revolution and it will stay locked after the first second or third click 5 Connect your air tool to the other end of the Hose using another coupler and thread seal tape 3 To unlock slowly pull until the clicking stops and let it retract until the Hose Stopper hits the Hose Guide 6 Follow all instructions from the air tool and compressor for set up and use CAUTION Hold on to the Hose while it is rewinding to avoid damage to the Hose Reel 7 When finished using the Hose disconnect the air tool and retract the hose Wipe the Hose Reel clean with a dry cloth Z Q lt oO Lu ou O Item 69234 For technical questions please call 1 800 444 3353 Page 5 AONVNALNIVIN User Maintenance Instructions AWARNING TO PREVENT SERIOUS INJURY Detach air supply from this product before performing any inspection maintenance or cleaning procedures Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equi
7. ion of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TEC
8. otar Swivel Collar 8 Spring Hose Guard 1 RE Hub Bearing 1 Assembl Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Part Description _ Qty 1 Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Item 69234 For technical questions please call 1 800 444 3353 Description _ Qty i Bracket Assembl Assembl Ratchet Locking Gear Spacing Washer__ 1 Retaining Ring 1 Bolt al Lock Washer _ 4 Setscrew 1 1 Page 7 MAINTENANCE Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitat
9. pment If abnormal noise vibration or leaking air occurs have the problem corrected before further use Cleaning Maintenance and Lubrication Note These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the Hose Reel 1 BEFORE EACH USE inspect the general 2 AFTER EACH USE re wind the hose onto the reel condition of the tool Check for and wipe the Hose Reel clean with a dry cloth loose hardware or housing WARNING Internal spring is not user e misalignment or binding of moving parts serviceable or user replaceable e cracked or broken parts and e any other condition that may affect its safe operation Hose Replacement 1 Remove the Hose Stopper from 5 Use thread seal tape on the hose fitting threads the hose and set aside and screw the fitting onto the swivel and tighten 2 Pull out the old Hose and securely 6 Attach the Hose Stopper on the end of lock the Hose Reel the Hose near the Outlet fitting 3 Disconnect the old hose from the swivel 7 Carefully release the Drum Latch and allow joint and remove the hose the Hose to wind onto the reel evenly distributing the Hose across the Reel 4 Run the new hose through the Guide Roller and through the opening in the drum flange CENTRAL Page 6 For technical questions please call 1 800 444 3353 Item 69234 Part Description Qty Drum mounting bracket side Mounting Bracket Swiverc
10. ssages that follow this symbol to avoid possible injury or death Indicates a hazardous situation which if not avoided will result in death or serious injury Indicates a hazardous situation which if not avoided wn gt m m lt AWARNING ACAUTION CAUTION could result in death or serious injury Indicates a hazardous situation which if not avoided could result in minor or moderate injury Addresses practices not related to personal injury IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS WARNING When using tools basic precautions should always be followed including the following To reduce the risks of electric shock fire and injury to persons read all the instructions before using the tool Work Area 1 Keep the work area clean and well lighted Cluttered benches and dark areas increase the risks of electric shock fire and injury to persons Personal Safety 1 Stay alert Watch what you are doing and use common sense when operating the tool Do not use the tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating the tool increases the risk of injury to persons Dress properly Do not wear loose clothing or jewelry Contain long hair Keep hair clothing and gloves away from moving parts Loose clothes jewelry or long hair increases the risk of injury
11. ts on the Support Post and 2 Replace the Bolts and tighten reposition to move the guide rollers if needed for the desired mounting location wall floor or ceiling Mounting Reel 1 Choose a mounting location that is free of electrical 3 Check for hidden wiring then drill holes to wiring or other obstructions and is sturdy enough accommodate 1 2 bolts not included to support the weight of the Reel and hose as f f well as the force used to extend and retract it 4 Mount the Reel and secure in place with four bolts 2 Make a paper template from the mounting plate of the Reel Mark the center of the bolt holes in the desired mounting location Page 4 For technical questions please call 1 800 444 3353 Item 69234 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Inspect tool before use looking for damaged loose and missing parts If any problems are found do not use tool until repaired Adjust the Spring Tension 1 Pull out approximately six feet of Hose 3 Run the hose back through the guide and re attach the hose stopper 2 Remove the Hose Stopper from the Hose and slide the Hose out of the Roller 4 Pull the Hose out several feet to check the tension Guide so the Hose is hanging loose a To increase tension wrap the loose hose one time around the Reel Drum b To
Download Pdf Manuals
Related Search