Harbor Freight Tools 2000 lbs. Capacity Foldable Engine Stand Product manual
Contents
1. Keep bystanders out of the instructions Improper assembly area during assembly can create hazards 5 Do not assemble when tired 2 Wear ANSI approved safety goggles or when under the influence and heavy duty work gloves of drugs or medication during assembly 6 Weight capacity and other product 3 Keep assembly area clean and well lit capabilities apply to properly and completely assembled product only Use Precautions Failure to heed these instructions may result in personal injury and or property damage 1 Study understand and follow all 7 Hold Handle while removing the Pin instructions before operating this device Wear ANSI approved safety goggles 2 Do not exceed rated capacity and heavy duty work gloves during use ne aware OF dynamic loading 9 Do not use for aircraft purposes Sudden load movement may briefly create excess load 10 Inspect before every use causing product failure do not use if parts loose or damaged 3 Use only on hard level surfaces 11 This product is not a toy Do not allow children to play with or near this item Lock mounting plate rotating mechanism before applying a load 12 Use as intended only 5 Assure load is centered and secured 13 Maintain product labels and nameplates to mounting attachments These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement 6 Only use when Legs are fully extended outward and Eye2. Pins and R Pins are in place Page 2 For technical questions please call 1 800 444 3353 Item 69522 Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the A beginning of this document including all text under subheadings therein before set up or use of this product 1 Attach 3 1 2 Casters 15 to the straight back section of the Base 8 using Bolts 11 Spring Washers 10 and Nuts 9 Insert Bolts from the bottom through the Casters first 2 Attach 3 Casters 16 to the angled front sections of the Base 8 using Bolts 12 Spring Washers 10 and Nuts 9 Insert Bolts from the top through the Base first Leg Lock Pins 13 Leg Lock Pins 13 Base 8 Figure B Attach Legs Note There are five M14 diameter Bolts The longer one part 4 is used to attach the top of the two Braces 5 to the Column 2 5 Attach Column 2 to Base 8 using Bolts 3 Washers 7 and Nuts 6 3 1 2 Caster 15 Column 2 Bolt 11 Figure A Attach Casters to Base 3 Attach a 3 1 2 Caster 15 to the end of each Leg 17 using Bolts 11 Spring Washers 10 and Nuts 9 4 Place Legs 17 into slots in Base 8 with the Casters 15 turned downward Use two Leg Lock Pins 13 to secure each Leg Secure each Leg Lock Pin using an R pin 14 Item 69522 For technical questions please call 1 800 444 3353 Page 3 6 Place the tops of the Braces 5
3. flat 8 Insert the Mounting Plate 23 against the Column 2 aligning the through the Column 2 holes Insert Bolt 4 through the 9 Braces and Column and secure grips from the Handle 18 with Washer 7 and Nut 6 insert the Handle through the hole 7 Secure the bottom ends of the in back of the Mounting Plate 23 Braces 5 to the Base 8 using and replace the rubber grip Bolts 3 Washers 7 and Nuts 6 Slide off one of the rubber Column 2 Handle 18 Handle Plate 23 Figure E Attach Mounting Plate 10 To lock Mounting Plate 23 rotation Column 2 N align a hole on it with the hole on the top of the Column 2 and insert the Pin 1 11 Attach the Mounting Arms 21 22 to the slots in the Mounting Plate 23 using the Bolts 19 Washers 7 Fender Washers 20 and Nuts 6 Figure D Attach Column Braces PITTSBURGH Page 4 For technical questions please call 1 800 444 3353 Item 69522 Operating Instructions beginning of this document including all text under subheadings therein Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the before set up or use of this product Mounting Engine TO PREVENT SERIOUS INJURY AWARNING Before attaching an engine to the stand confirm that its weight does not exceed the Stand maximum capacity 1 Lock both Legs 17 in lowered position 5 Place the bolts not included through with two Leg Lock Pins 13 per Leg the Mounting P
4. use the Stand while it is folded This is only for compact storage Page 6 For technical questions please call 1 800 444 3353 Item 69522 Parts List and Diagram 6 M14Nut 9 7 O14Washer_ _ 9 8 Base tt 9 MBNut_ 24 12 Bolt M8x16 8 Record Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Item 69522 For technical questions please call 1 800 444 3353 Page 7 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high qual
5. warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
6. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference P I TTSB UR G H ITEM 69522 2000 Ib Foldable Visit our website at http www harborfreight com Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Copyright 2012 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Weight Capacity 2 000 Ib Face Plate 9 3 4 W x 5 7 8 H x 13 16 thick Important Safety Information Assembly Precautions 1 Assemble only according to these 4
7. d by the crane remove the bolts securing the 2 S th i ly to th l ee N Mounting Arms 21 22 to the engine Use the crane to support all of the engine s weight directly overhead but do not start lifting the engine stand Item 69522 For technical questions please call 1 800 444 3353 Page 5 Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM STAND FAILURE Do not use damaged equipment Make sure the stand is stable If any unsafe conditions are found take it to a qualified technician for service or repair 1 BEFORE EACH USE inspect the 2 Keep Engine Stand clean and general condition of the Stand free of dirt or grease Check it for cracks bends in the 3 Before each use check that metal signs of unusual wear or any other condition that may affect its safe operation If any are 4 Check that the Casters are found do not use the Stand clean and turn properly 5 AFTER USE clean external surfaces of the stand with a clean moist cloth hardware is securely fastened Folding the Stand for Storage 1 Remove the forward R pin 14 4 Insert the Leg Lock Pin 13 through the upper hole in the Base 8 so 2 R the Leg Lock Pin 13 PONES O E E E that it holds the Leg in place and 3 Fold up the Leg 17 lock it in place with the R pin 5 Repeat for the other Leg WARNING Do not
8. ity and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our
9. late 23 side and secured in place with R pins 14 securely tighten them into the engine The bolt heads must press against the back of the Arms Determine the thread type and if needed use flat washers length of bolts not included needed not included as spacers to thread into the engine block Remove the Pin 1 from the Column 2 Use grade 8 bolts that are long enough O MOMEN INE BOIS 19 ana to fit through the Arms and thread as maL ME oom ATMS 21 22 deeply as possible into the engine block to the Mounting Plate 23 securely 7 Slowly lower the hoist engine crane 4 Align the Mounting Arms 21 22 with four mounting bolt locations on the engine WARNING Use all four Arms when 8 Hrs ia the engine from attaching an engine to the Stand e hoisvengine crane sold separately until all the engine s weight is held by the stand 9 Slowly rotate the engine to the desired angle and insert the Pin 1 into the top of the Column 2 Rotating Engine TO PREVENT SERIOUS INJURY Be prepared for sudden engine AWARNING movement before removing Pin Stay clear of engine 1 While holding onto the Handle 18 2 Use assistance to rotate the engine and the engine to prevent it from to the desired angle and insert the accidental rotation remove Pin 1 Pin 1 into the top of the Column 2 Removing Engine 1 With assistance rotate the 3 Once the engine is properly engine to its initial position supporte
Download Pdf Manuals
Related Search