Harbor Freight Tools 2 Pc Amber Clearance Marker Lamps Product manual
Contents
1. W x 1 H Housing 4 1 8 L x 2 1 16 W x 5 8 H Lens 4 Lx 2 W x 11 16 H Mounting Holes 1 4 diameter and 3 apart at centers Construction White ABS Poly and lens is red amber acrylic Light Bulb 12VDC 2 included Important Safety Information Assembly Precautions 1 Assemble only according to these instructions Improper assembly can create hazards N Wear ANSI approved safety goggles and heavy duty work gloves during assembly 3 Keep assembly area clean and well lit 4 Keep bystanders out of the area during assembly a Do not assemble when tired or when under the influence of alcohol drugs or medication Use Precautions Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Always check hardware and assembled parts after assembling All connections should be tight and hardware tightened Weight capacity and other product capabilities apply to properly and completely assembled product only 1 This product is not a toy Do not allow children to play with or near this item 2 Use as intended only 3 Inspect before every use do not use if parts are loose or damaged Aa Use the right product for the job There are certain applications for which the Lamp was designed a Make certain to follow all local DMV Department of Motor2. Vehicles laws regarding vehicles and vehicle lighting requirements o Do not cut or rewire any part of the Lamp Make certain the vehicle is turned off before doing any maintenance The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement Page 2 For technical questions please call 1 888 866 5797 Item 93226 93227 Assembly Instructions A before set up or use of this product Before operating this product be sure that you 4 have all parts described in the Parts List and Assembly Diagram located on page 4 of this manual If you do not have experience doing this type of electrical work the job should be done by an automotive service technician 1 Make certain that the vehicle s engine is OFF before doing any maintenance or installation Proceed with the 6 following steps for assembling the 2 Piece Marker Clearance Lamp 2 Use a pin connector or in line splice connector neither included to connect the 2 Piece Marker Clearance Lamp to your vehicle When using an in line splice connector it is not
3. necessary to strip the wires 3 Insert the wire from your vehicle into one channel of the in line splice connector Insert the wire extending from the Lamp into the second channel of the in line splice connector Fold down the tab on the in line splice connector to make the connection Installing the Light Bulb Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein When mounting the lights to a trailer both the forward amber and rear red marker lights are connected to the trailer s tail light wires 5 When attaching the Lamp to the vehicle or trailer the ground screw must make contact with a metal surface to assure proper grounding Once the wires are properly connected test them before setting the Lamp in place To mount onto a trailer or vehicle use the mounting holes on the Lamp The mounting holes are spaced 3 from center to center and are 1 4 diameter Make certain that the ground screw makes proper contact with a metal surface Mounting hardware is not included 1 To remove the Lens insert a screwdriver between the Lens and Housing Gently twist the screwdriver to pry the Lens off of the Housing 2 Gently grasp the Light Bulb 12VDC included and slide it into the socket Twist until the Light Bulb locks in place See Figure A Housing Light Bulb Socket Figure A 3 Verify that the Light Bul
4. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference Haul viaster 2 PIECE al AMBER ITEM 93226 RED ITEM 93227 Visit our website at http www harborfreight com REV 13k Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2005 by Harbor Freight Tools All rights reserved m z No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this any shape or form without the express written consent of Harbor Freight Tools product Failure to do so can result in Diagrams within this manual may not be drawn proportionally Due to continuing serious injury SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Product Application Marker Clearance Lamps Overall Dimensions 4 1 8 L x 2 1 16
5. b is Item 93226 93227 For technical questions please call 1 888 866 5797 securely in place Snap the Lens back onto the Housing Page 3 Li ited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election
6. or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state Record Serial Number Here Note If product has no serial number record Note Replacement parts are month and year of purchase instead not available for this item 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
Download Pdf Manuals
Related Search