Harbor Freight Tools 2.5 ton Scissor Jack Product manual
Contents
1. they can be caught in moving parts Wear restrictive hair covering to contain long hair Do not overreach Keep proper footing and balance at all times Do not reach over or across a Leveling Jack under a load Maintain tools with care Keep tools clean for better and safer performance Follow instructions for lubricating and changing accessories The handle must be kept clean dry and free from oil and grease at all times Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Stand clear of the Leve2. DRILLING HOLES CHECK FOR ANY CHASSIS COMPO NENTS WHICH MAY BE INSIDE THE FRAME LOOK FOR ELECTRICAL LINES AND WIRES GAS TANK GAS LINES WATER AND HOLDING TANKS GENERA TOR FUEL LINES AND WATER HEATER LINES MAKE SURE AREA IS CLEAR OF THESE COMPONENTS BEFORE DRILLING 2 Hold the Jack against the frame and using the Mounting Brackets 9 as a template mark the locations of the 8 mounting holes on the RV or Trailer frame Remove the Jack Use a center punch not included and hammer not included to mark the center of each hole 4 Use a drill not included to make a pilot hole 1 8 Then use a 5 16 drill bit not in cluded to complete each hole Use eight 3 8 tapping screws not included with eight lock washers not included to attach the Jack to the frame WELD ON INSTALLATION 1 Refer to Installation and steps 1 and 2 under Bolt on Installation on pages 4 and 5 of this manual 2 Weld at least four 1 welds on the Jack Mounting Brackets 9 when attaching to the frame OPERATION TRAILERS TRAVEL TRAILERS AND 5TH WHEELS 1 Park on level ground 2 Level trailer travel trailer 5th wheel front and back with small carpenter s level not in cluded or round bubble level not included Place leveling blocks not included in front of one tire on trailer Slowly pull forward to drive the trailer up onto the blocks When the trailer is level stop and block all tires to keep from rolling forward or b
3. F HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 96406 For technical questions please call 1 800 444 3353 Page 7
4. HAUL MASTER LEVELING SCISSOR JACK 5 000 LB CAPACITY 111 1196406 OPERATION INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http Awww harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2007 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 SPECIFICATIONS Steel Rod Rubber Grip and Attached Socket and Dimensions 25 3 4 L X 15 32 Diameter 5 Long Rubber Handle and Grip Overall Dimensions 26 1 4 Total Length X 4 5 8 High X 6 3 4 Wide Collapsed for Storage Bolt On see directions on page 5 of this manual Jack Mounting Weld On see directions on page 5 of this manual Unmounted use is NOT recommended 14 36 Ib Jack Only Save This Manual You will need this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Write the product s serial number in the back of the manual near the assembly diagram or write month and year of purchase if product has no number Keep this manual and i
5. ackward 3 Using Handle Wrench 16 lower the Scissors Jack on the lowest side first to get level Use Jacks on opposite sides for best stabilization 4 After Jack makes firm contact with ground turn Handle Wrench 16 twice to insure Jack will not loosen from trailer during use NOTE When RV or trailer will not be moved for several days periodically check Jacks to be sure they have not worked loose MOTOR HOMES 1 Park on level ground and level motor home front and back see step 2 in previous sec tion SKU 96406 For technical questions please call 1 800 444 3353 Page 5 2 Using Handle 16 lower Jacks on opposite sides for stabilization see steps 3 and 4 in previous section NOTE If motor home comes with factory installed hydraulic levelers the Leveling Scissor Jack can be used to provide additional stabilization Follow the directions for installation found in this manual on pages 4 and 5 MAINTENANCE ike Before use inspect the Leveling Scissor Jack for cracks dirt or debris in threads loose welds or bolts and anything else that looks or feels abnormal If anything is found do not use the Jack Have it repaired or replaced 2 Keep the Leveling Scissor Jack clean and dry 3 Periodically lubricate Screw Rod 4 Threads with high quality light weight oil not in cluded LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standar
6. ds and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death in juries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear
7. ling Jack when attempting to level any trailer or RV Never exceed the Jack s capacity of 5 000 Ib Check the trailer or RV s manual to determine the actual gross weight before attempting to level it This Jack s weight capacity is 5 000 Ib only between 13 3 4 and 23 1 2 the weight capacity dras tically reduces as the height drops below this level Do not apply a load to this jack below 13 3 4 in height Never stand on the Jack and never have people or pets in the trailer or RV you are attempting to level Place the Leveling Jack on a flat level surface Only use this Jack on a stable clean dry surface that is capable of sustaining the weight of the Jack and the load it is stabilizing Stabilize the load Ensure that the load remains stable at all times Do not move the load while it is on the Leveling Jack Block all of the wheels when leveling an RV or trailer SKU 96406 For technical questions please call 1 800 444 3353 Page 3 23 24 25 Do not use this leveling scissor jack for aircraft purposes Some RV sub frames are not capable of handling any additional forces beyond its intended design strength to support the cabin weight Contact your RV manu facturer for the sub frame strength information before use of this Scissor Jack The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the ope
8. nvoice in a safe and dry place for future reference SAFETY RULES AND WARNINGS WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in serious injury SAVE THESE INSTRUCTIONS NOT USE THIS LEVELING JACK FOR LIFTING Do not use to change tires 2 Keep space around Jack as uncluttered as possible when using this Leveling Scissor Jack Clutter can hinder smooth operation and possibly cause accidents and or serious personal injury Keep area well lit Keep out from under trailer or RV Keep hands away from scissor mechanism Do not exceed maximum weight capacity of 5000 Ib Wear ANSIl approved safety goggles and heavy duty work gloves during use Level only at trailer or RV manufacturer s recommended lifting points Install this Leveling Scissor Jack in accordance with DMV regulations N Keep children away Children must never be allowed in the Leveling Jack area Do not let them handle the Jack at any time SKU 96406 For technical questions please call 1 800 444 3353 Page 2 17 18 20 21 22 Use the right tool for the job There are certain applications for which this Level ing Scissor Jack was designed It will do the job better and more safely at the rate for which it was intended Do not modify this Jack and do not use this Jack for a purpose for which it was not intended Dress properly Do not wear loose clothing or jewelry as
9. rator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator UNPACKING When unpacking check to make sure the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible ASSEMBLY This Leveling Scissor Jack comes completely assembled For further information on parts and assembly break down see the diagram on page 7 of this manual INSTALLATION WARNING DO NOT USE THIS LEVELING SCISSOR JACK WHILE UNMOUNTED Park RV or Trailer on level ground Prevent the wheels from rolling by applying emer gency brake and wheel blocks not included Check the following before proceeding with the installation a Attach Jack to the frame of the RV or Trailer using two c clamps not included or two vise grips not included Close the Jack using the Handle Wrench 16 to check the frame location Make sure the Jack will clear any chassis components nearby b Open the Jack enough to touch the ground Recheck the location on the frame and adjust if needed c Once in place apply enough pressure between the ground and the Jack to ensure that it will not move during the rest of the installation process Remove the c clamps not included or vise grips not included SKU 96406 For technical questions please call 1 800 444 3353 Page 4 BOLT ON INSTALLATION 1 WARNING BEFORE
10. the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 96406 For technical questions please call 1 800 444 3353 Page 6 PARTS LIST AND DIAGRAM Part Description e Part Description e umer Fano Fame o Mounting Brackets 2 Part Description Q ty 17 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT O
Download Pdf Manuals
Related Search