Harbor Freight Tools 6/12V Product manual
Contents
1. cccccceceeeeeeeeeeceeceeeeeeeeeeees 7 Wanad ci c02s3 sensczereisisiccextnon deve rieoatoeeadtene 7 WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death AWARNING ACAUTION NOTICE CAUTION IMPORTANT SAFETY INSTRUCTIONS T INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS WARNING When using tools basic precautions should always be followed including the following 1 Wear ANSI approved safety goggles during set up and use of the Battery Tester 2 Test ina well ventilated area Explosive gases may be produced during testing Do not smoke cause sparks or strike matches near the battery when testing 3 Refer to the user manual of the Battery being tested for testing instructions and precautions prior to using the Battery Tester 4 Do not connect in reverse polarity 5 Do not expose this product to rain or wet conditions 6 Maintain this product Check for breakage of parts and any other condition that may affect this product s operation If damaged have the unit repaired before use Page 2 10 11 For technical questions please call 1 800 444 3353 Indicates a hazardous situation which if not avoided will result in death or serious injury Indicates a hazardous situation which if not avo2. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference i N a a es TEM 01747 6 VOLT 12 VOLT BATTERY LOAD TESTER TAIM arent CAAS C0n IN COLOCRANKIN 2 WA no N ewe Nh w Es When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved l No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included wn gt A m lt Table of Contents DOCU E E TE 2 Specifications cccceccccecceeeeeeeseeeeeeeeeeeees 3 FUNGUOMNS arsada aR 4 Operation sesine nan 5 Maintenance
3. PACITY by IN COLOCRANKING AMPS CCA LOAD VOLT 10 2 10 4 10 6 10 8 1 0 1 2 4 MIN CRANK VO 77 82 8 ee Q ot ARTER TEST Meter Display 1 CONNECT CLAMPS TO BATTERY TESTER BATTERY TERMINALS 2 PRESS LOAD SWITCH 6 12 VOLTS MAXIMUM 10 SEC MODEL BT 100 3 READ METER WITH N m S d zZ Toggle Switch Page 6 For technical questions please call 1 800 444 3353 Item 61747 User Maintenance Instructions Procedures not specifically explained in this manual must A be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Inspection Maintenance and Cleaning Note These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air operated tool 1 Periodically check all nuts bolts and screws for tightness 2 Store in a clean dry location 3 Clean the outside of the unit with a damp cloth Never use solvents to clean any parts of this tool Allow tool to dry completely before use 4 Use compressed air to blow out debris from the load vents 5 After each use clean the Cable Clamps of any possible battery electrolyte Apply a thin coat of silicon grease to prevent corrosion Record Product s Serial Number Here Note If product has no serial number re
4. chnical questions please call 1 800 444 3353 Page 3 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Testing the Battery 1 To help ensure a good connection wipe the battery If the recharging will not bring the reading above terminals with a cloth to remove any dirt and grease 12V the battery is defective If it shows no reading verify that the tester is connected properly If the 2 Connect the red positive Cable Clamp tester is connected properly the battery is defective to the positive terminal on the 6 or 12V lead acid battery See figure A 5 Press and hold the Toggle Switch for at least 5 seconds to simulate an actual 3 Connect the black negative Cable Clamp to the load on the battery See figure A negative terminal on the battery See figure A Turn clamps slightly to ensure a good connection 6 View the Meter Display and read the battery condition Refer to the 4 With the clamps connected the tester s gauge will Battery Condition Analysis chart on page 6 show the battery s current charge See figure B If it is less than 12V disconnect the 7 Release the Toggle Switch and remove battery and recharge before testing the Cable Clamps from the battery Testing the Charging System AWARNING AVOID CARBON MONOXIDE POISONING This gas comes from the vehicle s
5. cord month and year of purchase instead Replacement parts are not available for this item MAINTENANCE Item 61747 For technical questions please call 1 800 444 3353 Page 7 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or rep
6. exhaust and is colorless and odorless It can cause SERIOUS INJURY or DEATH if inhaled 1 Connect the Cable Clamps to the 3 View the Meter Display and read the charging battery as previously described system condition far right on the gauge Refer to the Battery Condition Analysis section to the right 2 Outside or in a well ventilated area start the vehicle engine and run at fast idle speed 4 Turn vehicle s engine off then remove Cable Clamps a A Testing the Starter NOTE The engine should be at normal 4 View the Meter Display and read the voltage lt operating temperature and the battery should A reading of 9 Volts or less indicates be fully charged before doing this test excessive current draw This may be due to a poor connection a failing starter 1 Connect the Cable Clamps to the or a battery of insufficient size for the motor battery as previously described oats f 5 When finished disconnect the Cable Clamps 2 Disable the ignition so the engine will not start restore ignition and store tool in a clear Refer to your vehicle s manual dry location away from children 3 Have an assistant crank the engine Note the voltage reading during cranking Page 4 For technical questions please call 1 800 444 3353 Item 61747 Battery Condition Analysis V BATTERY CAPACITY IN COLDCRANKING AMPS CCA 0 4 10 6 10 8 1 0 11 2 LAURE a a ERE OEB UBER NOTTE Meter Display Battery capacity
7. ided could result in death or serious injury Indicates a hazardous situation which if not avoided could result in minor or moderate injury Addresses practices not related to personal injury Use this product in accordance with these instructions taking into account the working conditions and the work to be performed Use of this product for operations different from those intended could result in a hazardous situation This product is not a toy Keep it out of reach of children Maintain labels and nameplates on the unit These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement People with pacemakers should consult their physician s before use Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure Caution is necessary when near coil spark plug cables or distributor of running engine Engine should be off during distributor adjustment Undercharged lead acid batteries will freeze during cold weather Do not test or charge a froz n battery Item 61747 12 When connecting the Battery Cables to the 16 Do not drop the Battery Tester as it battery avoid creating sparks especially when may affect proper operation the battery is being charged Explosive gases are created during charging Sparking could 17 Do not smoke or have open flames near the battery also damage the vehicle electrica
8. is good May or may not be fully charged Check the charge state by testing the Specific Gravity SG with a Hydrometer not included If SG is less than full charge check for possible ing system trouble Recharge to full level If the Display Meter needle is steady the battery capacity is not good Battery may be defective or partly discharged Check SG If over 1 225 the battery is defective Weak If below 1 225 recharge battery and retest Yellow Area If there is a difference in SG between cells over 2 points 0 025 a particular cell may be damaged If charging does not bring SG to full charge level then battery is either sulfated or has lost its active material If the Display Meter needle is falling the battery is defective or has a bad cell For a quick check release the load Bad Toggle Switch and note Display Meter reaction Red Area If voltage recovers to its full potential after only a few seconds the battery is probably defective If the voltage recovers slowly the battery may only be run down Check SG recharge and retest Charging System If the Display Meter needle reads OK charging system is functional Alt amp Reg Test If it falls on the low red or high red areas charging system may be malfunctioning z e lt ad m Q Item 61747 For technical questions please call 1 800 444 3353 Page 5 Functions Handle Red Positive Cable Clamp Black Negative Cable Clamp Se BATTERY CA
9. l system 18 Do not connect the Battery Tester to 13 Do not touch the cooling vents on the Battery the battery while the engine is running Tester during or immediately after testing Turn the engine off before connecting ps ihe battery Thay Become vary hat 19 The warnings and precautions discussed in this ie 14 When placing the Battery Tester in the vehicle s manual cannot cover all possible conditions and lt engine compartment take special care that situations that may occur It must be understood N the metal housing of the Tester does not by the operator that common sense and caution come in contact with either terminal of the are factors which cannot be built into this battery or other electrical connections product but must be supplied by the operator 15 Be certain of the test battery polarity before connecting the test Cable Clamps The red Cable Clamp goes to the positive terminal of the battery The black Cable Clamp goes to the negative terminal of the battery Reversing Battery Tester Cable Clamps on the battery will damage the tester AX SAVE THESE INSTRUCTIONS Specifications Testing Capability 6 and 12 VDC battery tester Load Test 100 amps Capacity 500 1000 cold cranking amps Display Meters Analog 0 16 VDC max SPECIFICATIONS 10 seconds per test with Test Cycle 1 minute cool down 3 tests in 5 minutes Battery Cable 16 3 4 IN long including clamps Copper plated clamps Item 61747 For te
10. lace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state C E N Cle 3491 Mission Oaks Blvd e PO Box 6009 Camarillo CA 93011 800 444 3353
Download Pdf Manuals
Related Search