Hans Grohe Axor 17010XX1 User's Manual
Contents
1. faucet continues to drip after seal damaged replace 95008000 seal too little hot water high temperature limit stop set reset high temperature limit stop incorrectl Replacement Parts a handle s amp o 94192XX0 flange 92620XX0 pull rod Cleaning Recommendation for Hansgrohe Products Modern sanitary faucetry and shower fixtures consist of very different materials to comply with the needs of the market with regard to design and functionality To avoid damage and returns it is necessary to consider certain points when cleaning Cleaning materials for faucets and shower products Acids are necessary ingredients of cleaning materials for removing lime However please pay attention to the following points when cleaning faucets and shower products Use only cleaning materials intended for the application Never use cleaning materials which contain hydrochloric formic or phosphoric or acetic acid as these can cause considerable damage Do not mix one cleaning material with another Do not use abrasives such as cleaning powders sponge pads or microfiber cloths Cleaning Instructions for Faucets and Shower Products Please follow the cleaning material manufacturer s instructions In addition please note the following Clean your faucets and shower products as and when required Follow the label instructions Do not allow any cleaner to remain on the product for longer than necessary Regular cle2. Axor Carlton Single Control Lavatory Faucet 17010XX1 Technical Specification Hole size in mounting surface Minimum 1 3 8 Maximum 1 5 8 Maximum mounting surface depth 1 1 4 Flow rate 2 2 GPM Maximum operating pressure 145 PSI Recommended operating pressure 22 72 5 PSI Recommended hot water temp 120 140 F M3 cartridge with Boltic handle screw Some governing bodies require that the water heater be set to 120 F or less Please know and follow all local codes when setting the temperature on the water heater Installation Considerations e _ For best results Hansgrohe recommends installation by a licensed professional plumber e Large differences in pressure between the hot and cold supplies should be balanced e The supply hoses on this faucet require supply stops with 3 8 compression fittings not included e This faucet has a high temperature limit stop It ships from the factory on the maximum setting but may be reset to a lower temperature if desired Install the faucet Place the faucet and sealing ring on top of the stud mounting surface Install the mounting flange over the stud Thread the collar onto the stud until the mounting flange is firmly against the bottom of the mounting surface sealing ring mounting flange collar Secure the supply lines to the stop valves with the 3 8 compression fittings not included Use two wrenches to insure that supply hoses
3. aning will prevent scale buildup and water spotting When using spray cleaners spray first onto a sponge or cloth Do not spray directly onto the faucet or shower product as drops could enter openings or gaps and cause damage e After cleaning rinse thoroughly with clear water to remove any cleaner residue Important Residues of liquid soaps shampoos and shower foams can also cause damage so rinse with clean water after using Please note If the surface is already damaged the effect of cleaning materials will cause further damage e Components with damaged surfaces must be replaced otherwise this could cause injury Damage caused by improper treatment will not be covered by our warranty Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe Inc Hansgrohe This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1 1996 and installed in either the United States or Canada WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only WHAT IS COVERED BY THE WARRANTY This warranty covers only your Hansgrohe manufactured product Hansgrohe warrants this product against defects in material or workmanship as follows Hansgrohe will repair at no charge for parts only or at its option replace any product or part of the product which proves defective because of imp
4. do not twist For proper operation of the faucet hot should be on the left and cold should be on the right Install the drain Re set the high temperature limit stop if desired Install the handle Turn on the water and check for leaks at all connections Install the pop up drain Remove the plunger assembly Hai Unscrew the drain outlet flange from the tee plunger Unscrew the tailpiece from the tee Wrap height adjuster the threads with two layers of Teflon tape and replace flange Install the white flexible sealing gasket to the flange Place it in the sink outlet From under the sink install the black mack gasket white friction ring and retainer nut BERN to the flange Do not tighten the nut against 99 the bottom of the sink at this time MES k gasket QQ Thread the tee and tailpiece to the flange eee 9 The pivot must face the faucet If necessary turn the drain assembly ama ted fiction ring Tighten the retainer nut PI he ol bl hed retainer nut ace the plunger assembly in the drain Install the horizontal rod so that the end goes te through the loop in the bottom of the height adjuster Install and hand tighten the pivot ball nut Attach the swivel connector to the end of the horizontal rod Attach the swivel connector to the end of the vertical rod Position as desired and tighten with a small flathead screwdriver tailpiece orizontal rod swivel connector Re
5. ion of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from State to State You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson Moss Warranty Act PRODUCT INSTRUCTIONS AND QUESTIONS Upon purchase or prior to installation please carefully inspect your Hansgrohe product for any damage or visible defect Prior to installing always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product If you have questions at any time about the use installation or performance of your Hansgrohe product or this warranty please call or write to us at the toll free number and address printed above ansgrohe Hansgrohe Inc e 1490 Bluegrass Lakes Parkway e Alpharetta GA 30004 Tel 770 360 9880 Fax 770 360 9887 www hansgrohe USA com US Installation Instructions e Part No 90957101 01 e Revised 03 2007
6. n or return of the product for warranty service or for installation or reinstallation of the product D Accessories or related products not manufactured by Hansgrohe TO OBTAIN WARRANTY SERVICE Contact your Hansgrohe retailer or write to Technical Service at Hansgrohe Inc 1492 Bluegrass Lakes Parkway Alpharetta GA 30004 Or call Hansgrohe toll free at 800 334 0455 In requesting warranty service you will need to provide 1 The sales receipt or other evidence of the date and place of purchase 2 A description of the problem 3 Delivery of the product or the defective part postage prepaid and carefully packed and insured to Hansgrohe Inc 1492 Bluegrass Lakes Parkway Alpharetta Georgia 30004 Attention Technical Service if required by Hansgrohe When warranty service is completed any repaired or replacement product or part will be returned to you postage prepaid EXCLUSIONS AND LIMITATIONS REPAIR OR REPLACEMENT OR IN LIMITED CIRCUMSTANCES REFUND OF THE PURCHASE PRICE AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY INCLUDING MERCHANTABILITY Some States do not allow the exclusion or limitat
7. roper workmanship and or material under normal installation use service and maintenance If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made Hansgrohe may elect to refund the purchase price in exchange for the return of the product LENGTH OF WARRANTY Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences If you are a consumer who purchased the product for use primarily for personal family or household purposes this warranty extends for as long as you own the product and the home in which the product is installed If you purchased the product for use primarily for any other purpose including without 7 limitation a commercial purpose this warranty extends only i for 1 year with respect to Interaktiv and Retroaktiv products and ii for 5 years with respect to AXOR ShowerPower and Pharo products THIS WARRANTY DOES NOT COVER AND HANSGROHE WILL NOT PAY FOR A Conditions malfunctions or damage not resulting from defects in material or workmanship B Conditions malfunctions or damage resulting from 1 improper installation improper maintenance misuse abuse negligence accident or alteration or 2 the use of abrasive or caustic cleaning agents or no rinse cleaning products or the use of the product in any manner contrary to the product instructions C Labor or other expenses for the disconnectio
8. set the High Temperature Limit Stop optional Use a 4 mm Allen wrench to push the screw cover into the handle Retrieve the screw cover when the handle is removed Close the drain OR cover it with a wash cloth 4 Use the 4mm Allen wrench to loosen the handle screw 4 complete revolutions Remove the handle and put it in a safe place Remove the decorative nut cover and put it in a safe place Remove the handle screw from the stem of the E gt cartridge Remove the high temperature limit stop Ss Replace the high temperature limit stop so that the pin on the cartridge is in the desired slot on the limit stop Note the temperatures given in the diagram assume a water heater temperature of 140 F a cold water temperature of 50 F and a water pressure of 45 PSI Replace the decorative nut cover Replace the handle screw Use the Allen wrench to turn the screw 4 revolutions Replace the handle Finish tightening the handle screw Turn on the water and test the faucet User Instructions e Push the handle up to turn the water on e Pivot the handle to the left for hotter water to the right for cooler water e Push the handle down to turn the water off Troubleshooting Problem Possible Cause Solution too little water remove and clean aerator handle hard to turn debris in cartridge remove and flush cartridge replace if necessar debris in cartridge remove and flush cartridge replace if necessar
Download Pdf Manuals
Related Search