Home
Haier HWM90DD User's Manual
Contents
1. They can easilyslide in tothe tub andmay damage thetub e Pre treat all stains and heavily soiled areas for bestresults Do not overload your washer When loading wetitems keep water levelhigh enough soitems can float easilyin the water e Close the door properly after loading the clothes if you keep the lid up the washerwill not start Proper Use of Detergent e It is good washing practice toadd the detergentto the water before you addthe clothes sothat the detergentcan work effectively on yourclothes Notes Youcan less ormore detergent dependingon the size of the load water typein your living area whether it is soft or hard andwhether the clothesare heavily soiled or lightly soiled Bleach Dispenser e Bleach dispenser islocated on frontcorner under theloading door e Pour in recommendedamount of bleachinto dispenser during the first washfill Note Use only liquidbleach in dispenser Warning Be careful notto spill undiluted bleach on the washer cabinet or yourclothes As it isa storng chemical it maydamage some ofyour clothes or the finish ofthe washer if notproperly diluted Use the manufacturers chart on productcontainer for recommended use of liquid or powder bleach Softener inlet SOFTENER Softener inlet Please follow softener instructions for dose usage Before washing put the softener into the filling entrance can be found on the balancing ring by rotating the inner tub as illustrat
2. the wash 13 Do not try to remove clothes while the tub is moving Let it come toa complete stop 14 The lid must be closed when bowl is spinning 15 Do not operate your appliance when parts are missing or broken 16 Do not use this appliance for commercial clothes washing 17 Do not operate this appliance unless all enclosure panels are properly in place 18 Do not tamper with controls 19 The appliance is not instruct for use of young children of infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance 20 This appliance must be connected to a proper electrical outlet with the correct electrical supply 2 Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user repair instructions Make sure that you understand and have the skills to carry out 22 To reduce the risk of electric shock or fire do not use extension cords or adapters to connect the unit to electrical power source 23 If the washing machine is connected to a cord extension set or electrical portable outlet device make sure it is not in a position where it is subject to splashing or ingress of moisture 24 Ensure carpet does not obstruct the opening in the bases 25 Use the new hose provided The old hose should not be reused TABLE OF CONTENTS PAGE IMPORTANT SAFETY INSTRUCTIONS 1 2 OPERATI
3. Haier Haier Washing Machine HWM90DD IMPORTANT SAFETY INSTRUCTIONS Warning To reduce therisk of fire electric shock or injury when using your appliance follow basic precautions including the following 1 Read allinstructions before usingthe appliance 2 Use this appliance only for its intended purpose as described in this user and care guide 3 Use only detergents or softeners recommended for use in this appliance and keep them out of the reach of children 4 This appliance must be properly installed in accordance with the installation instructions before it is used 5 Never unplug your appliance by pulling on the power cord Always grasp the plug firmly and pull straight out from the outlet 6 Replace worn power cords loose plugs and power outlets immediately 7 Unplug your appliance before cleaning or before making any repairs 8 Do not operate your appliance in the presence of explosive fumes 9 Do not use hot water that exceeds 60 C in temperature 10 Do not use this appliance to wash clothes soaked spotted or washed in gasoline dry cleaning solvents or any other explosive or flammable substances that could ignite and explode 11 Clothes or rags used to clean flammable or explosive materials should not be washed in this appliance till all traces of this material has been removed to avoid an accident 12 Do not add or mix any flammable or explosive substances to
4. NG INSTRUCTIONS 4 Pants and Feature Sindra orrara rta bust 4 OPErFATIONS ERREUR AR a aon 5 Normal Operating SOUNGS ss xssurssncmnenrermmenemmentes 8 Lint LCR Eee 9 Install the liNNer COVE inining 9 CARE AND CLEANING GUIDE 10 Cleaning and Maintenance 10 Moving amp Vacationing 10 Storage of Your Washer in Cold Environment 11 TROUBLE SHOOTING 12 INSTALLATION INSTRUCTIONS 14 Tools and Materials Required 14 Unpacking Your Washer 15 Leveling Your Washer 15 Steps for Installations semaines 16 ELECTRICAL REQUIREMENTS 18 Power Interruptions 18 SPECIFICATION nirai Back Cover OPERATING INSTRUCTIONS Parts and Features Medium Cold Cold Start ause Delay Time Estimated Time Light ig Warm Warm xtra sh Spin Water Soil Rinse Speed Speed Delay Lever Signal Level LD CD Top lid Door switch 43 Inner tub Control panel Bleach injection inlet 4 Paddle Control panel seat Front door 5 Pulsator Cabinet Filter Filter Cover 6 Drain hose joint Leveling legs O Outer tub cover Inner cover 2 Bal
5. ance ring 4 Operations Heavy Duly HandWash Soak Stain Wash Hot Cold Normal e Quick Wash Wash Heavy Warm Cold Whites Delicate Casual Rinse Medium Cold Cold Start ause Colors Wrinkle Control e Spin Light Warm Warm Delay Time Estimated Time Exa Mesh Spin Water soil Cycles Process Ringe Speed speed Delay eyel Saal Level Delay e When not activated the display shows cycle remaining time through the washprocess e When delay is selected the indicatorlight will displaya minimum delay of 2hours Push button once for every additional1 hour delay for upto 24 hours Number of hourswill reduce until program starts Cycles e Heavy Duty For washing bigger thicker and heavier dirty laundries e Normal For washing cottons and linens Loadsthat are moderately or heavily soiled Whites For washing the clothes that isnot easy towash and need good rinseeffection such as underwearand children s clothes e Colors For washing colorfabrics Hand Wash To have hand wash effect onclothes e Quick Wash For quick washing oflight dirty laundries It need 24 30 minutes withoutextra rinse e Delicate Casual For washing of delicate fabrics e Wrinkle Control Helps to reduce wrinkles andeasy ironing Process This is toselect washing process e Soak will notwork in the Cycles Hand Wash Quick Wash Delicate Casual andWrinkle Control 5 e Water levelindicator will shutoff if o
6. ash tub If moving washer disconnect drain hose Turn the leveling legs clockwise all the way in Move and store your washer in upright position only To prevent mold or mildew leave lid open so moisture inside machine can evaporate 10 Storage of Your Washer e The washer must be stored at room temperature e If you just got delivery of a washer when outside temperature is below freezing do not operate until washer has warmed to room temperature Do not install or operate your washer where room temperature is below freezing 11 TROUBLE SHOOTING e Washer does not operate Check if unit is plugged in The plug may have come loose Check if the electrical wall receptacle is of proper voltage Check if the circuit breaker needs to be reset or if the fuse need to be replaced Check if the washer is overloaded load may need to be re balanced and clothes may need to be redistributed Check if the lid is open You may have to close the lid properly The washer pauses in some cycles This is normal in delicate or hand wash cycle which has short period of time You will not hear washer operation for a short period of time When the soak time is over it will start automatically Problems with water Not enough water coming out Water faucet may need to be turned on fully water Hoses may be tangled or wrinkled up Straighten out hoses Check water level selection it may need to be readjusted Water temperature i
7. ed in the drawing Try to avoid adding softener in if you do not intend to wash immediately The softener may harden and may cause a poor flow Please do not use softener in the following cases Selected rinsing times more than two Choosing rinse spin two in one program Normal Operating Sounds The following sounds are normally heard during the operation Of the washer e Tumbling sounds This is normalas the heavywet clothes in The washer arecontinuously being lossedaround e Air rushing noise This happenswhen the washertub spins at Very highspining speed e Wash andRinse cycles goingon and offwill also makeclicking Sounds Lint Filter e The lint filter must be used during washing It must be cleaned after each wash F IT Install 1 Take off the lint filter SA nO 2 Clean out thelint in thefilter Take off 3 Install the lintfilter Take of r Install the inner cover Install To prevent water spillage from tub 2 1 Open the top lid of the washing machine 2 Put the inner cover component on the outer tub cover lining up the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove 3 Firstly insert the inner cover shaft of one side into the corresponding outer tub cover shaft groove then push the other inner cover shaft into the corresponding outer tub cover shaft groove Please install in the designated position to guarantee there is no abnormal sound in openin
8. g The plug must be inserted into an outlet that is properly installed and grounded Consult a qualified electrician or service person if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded T Improper use of the plug can result in a risk of electric shock Wiring Requirements The washer must be plugged into at least 10AMP 220 240 VOL T 50 HZ GROUNDED OUTLET Note Where a standard two prong outlet is encountered it is the personal responsibility C and obligation of the consumer to have it replaced with a properly grounded three prong outlet Extension Cords We do not recommend that you use an extension cord Power Interruptions Occasionally there may be power interruptions due to thunderstorms or other causes Remove the power cord from AC outlet when a power outage occurs When power has been restored re plug power cord to AC outlet If outage is for a prolonged period clean washer before using it again 18 SPECIFICATION Rated voltage frequency 220 240V 50Hz Rated washing spinning capacity 9 0kg Spin speed max 700rpm Water level Water quantity about L 1 28 2 36 3 49 4 54 5 61 6 67 7 73 8 79 9 89 10 95 Max water consumption About 122L Normal program Injection pressure 0 03MPa 1 0MPa Weight approx 79kg
9. g Your Washer Remove all packing materials This Includes the foam base and all adhesive tape holding the washer accessories inside and outside Open the top lid to remove the styrofoam drum brace Pull to remove l Before using this washing machine please remove this shipping bar by pulling handle and dispose it properly otherwise the washing machine will be damaged Shipping bar Your washer has 4 leveling legs which are located on the bottom corners After properly placing your washer in its final position you canlevel your washer e Leveling legs can be adjusted by turning them counter clockwise to raise your washer or turning them clockwise to lower your washer A Adjustable foot High Low Warning Leveling of washeris very importantto prevent vibration during spin 15 Steps for Installation Select a away suitable location for the washer on a hard even surface from direct sunlight or heat source e g radiators base board heaters cooking appliances etc Any floor unevenness should be corrected with the leveling legs located on the bottom corners of the washer The washer must be placed at room temperature You must not place washer where the temperature is at below freezing Installing Your Washer Read through these instructions carefully before installation 1 Connect the hot and cold water inlet hoses to the hot and cold water faucet 2 Connect the other end to the corresponding washe
10. g and closing of the inner cover and the operation shall be smooth Do not remove the inner cover component after washing Outer tub cover Section enlarging _ Outer tub cover shaft groove Inner cover shaft Inner cover CARE AND CLEANING GUIDE Warning Always unplug your washer to avoid electric shock before cleaning Ignoring this warning may result in injury Before using cleaning products always read and follow manufacturer warnings to avoid personal Injury or product damage Cleaning and Maintenance Use only damp or sudsy cloth for cleaning control panel To avoid any kind of damage to cabinet finish wipe washer cabinet as needed If you spill liquid powdered softener bleach or detergent on the cabinet wipe cabinet immediately because it can damage the finish Do not use any abrasive harsh chemicals ammonia chlorine bleach concentrated detergent solvents or metal scouring pads Some of these chemicals may dissolve damage and or discolor your washer Remove pins or other sharp objects from clothes to prevent scratching of interior parts Leave lid open after you are done washing to allow inside of washer to dry and prevent bad odors Moving amp Vacationing Turn off water supply faucet s and disconnect hoses Drain water from all hoses This will prevent from damaging due to water leakage if the hoses accidentally get ruptured or they become loose Disconnect electrical plug Dry inner w
11. g in water Check water temperature or you need to add detergent as wash tub is being filled with water Spots or stains on your clothes this is due to incorrect use of fabric softener You may need to read proper instructions on the container and follow proper directions when using the softener Clothes are grayed or yellowed this is due to not pouring enough detergent for large loads You may have to add more detergent to the load Clothes are ripped amp have holes excessive wear amp tear this is due to sharp objects such as pins and belt buckles left in pockets You will need to remove small loose sharp objects Fasten belts zippers metal snaps etc Check if you are using undiluted bleach Never add undiluted bleach to wash Note Trouble Codes Reason EO Top lid not closed during delay start sequence E1 Blockage of drain hose E2 Top lid not closed during wash operation E4 The water inlet time exceeds the preset time 30minutes E7 The communication is bad F2 The protection ofwater overflow 13 INSTALLATION INSTRUCTIONS Tools and Materials Required Youwill need to have following tools to help you with theinstallation of yourwasher e Pliers e Wrench e Tape Measure e Gloves e Level Accessories Supplied Quantity 1 Hot amp Cold inlet hoses 2 2 Drain Hose Hook 3 Pipe Hoop 4 Inner Tub Cover ss ee fo ES 5 Outer Drain Hose 14 Leveling Your Washer Unpackin
12. nly Spin is selected Extra Rinse Once a programis selected pressthis button tohave a extra rinse The washer willadd a extrarinse Wash Speed Spin Speed e For selecting the speed of washingor spinning Water level Water levels may be setat the beginningof the washor at pause e During Soak Wash or Rinse press this buttonto manually replenish water Release to stop Function automatically is inactive when waterreaches the overflow protection level Signal e Signal volume canbe adjusted softer louder or off Soil Level e According toclothes soil level press this buttonto change washing time e Wash cycleincreases 2minutes for every soil level Temp e Toselect inlet water temperature for washand rinse Power On Off e Push the Power On Off button to switchthe machine on or off Start Pause e Once washer is powered and selections are chosen pushthis button once tostart washing e While unit isworking push this button once to pause it e If unit isin Pause mode push this buttononce to resume operation Delay Start and Estimated Time Indicator e Indicates remaining minutes when cycle isin progress e Indicates remaining hours during delay process e Indicates fault codesor conditions thatare not normal Loading the Washer e Load each itemloosely e Separate the whiteand colored clothes Separate heavy clothes from light clothes e Carefully check all pockets and cuffs for small items
13. r inlet located at the back of machine Cold water inlet hose Hot water inlet hose Note You may have to use pliers to tighten the coupling Do not over tighten because you may cause damage to the valve You should use the new hose sets supplied with the washer Old hose sets should not be reused 16 Install the drain hose to the side of the washer using the drain hose damp provided The drain hose must be placed into a drain pipe or sink at least 1 1 2inches in diameter Use the goose neck to the hose in place To avoid possible water back up the drain hose must reacha minimum height of 1000mm and a maximum height of 1500mm A Water Inlet Water Supply Hose Goose Neck Hose Bend Drain Hose 5 Plug the washer into a regular 220 240Volt 50Hz 10Amps outlet Note Carefully inspect all around the machine and at the back for any leaks and tighten any loose connections Caution If after completing these steps you are unsure that unit is properly installed contact a qualified installer To ensure that your washer is properly installed it is recommended that it be installed by a certified installer ae ELECTRICAL REQUIREMENTS Grounding Instructions This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with a grounded plu
14. s incorrect Check your water heater temperature Hot water needs to be at a temperature of at least 120 F 140 F 49 C 60 ee to make sure the inlet hoses are properly connected E g Hot to hot amp cold to cold Water leaks This is due to not properly installing drain hose or fill hoses Your home drain may be clogged You may need to tighten hoses check the plumbing or call a plumber Water will not drain This is due to not installing your drain hose properly Check theposition of the drain hose In order to drain properly make sure that top of drain outlet is less than 5 ft 1 5 m above the floor Washer is making noise Washer may need to be reinstalled Check washer installation section 12 Washer load may need to be re balanced as the load may be uneven Coins loose change buttons or other heavy objects could make noise read Operating Guide Normal Operating Sounds Squealing sound Due to overloaded wash tub Vibration Noise Due to not leveling washer properly on the floor and uneven distribution of clothes in the tub Problems with clothes Clothes are too wrinkled this is due to improper sorting overloading and washing in too hot water repeatedly Avoid overloading and resort your load Do not mix heavy clothes such as work clothes with light clothes such as blouses light shirts and delicate items You may need to wash in warm or cold water e Have soap residue detergent may not be dissolvin
Download Pdf Manuals
Related Search
Related Contents
取扱説明書・追加分(MacOS Xでの利用方法) E-MANUAL - Voelkner 認証表明の方法 Philips Ledino Suspension light 40746/17/16 Canon IR1600 Copier User Manual OActive® - VQ OrthoCare Mode d`emploi Cell Invasion & Detection Assay Kit Protocol & Instructions Dialogic D4PCIUFWEU Manual do Utilizador do Nokia 6170 Copyright © All rights reserved.
Failed to retrieve file