Haier Washer HWM75-7288 User's Manual
Contents
1. 1 Close the water faucet Locking lever 2 Press the locking lever Push down the slider Then pull off the water inlet hose Slider If the machine is used frequently the jointer of the water inlet hose can be kept on the faucet to prevent damaging the fixing screw How to change the direction of the drain hose 1 Dismantle the back cover of the washing machine 2 Press the spring lamination lightly and pull the top segment of the drain hose decumbent then put Back cover down the drain hose from the drain hose frame Drain hose frame 3 Put down the drain hose squeeze the drain hose lightly and take off the hook put the drain hose into R the cabinet Take off the small baffle which installed on the other drain outlet and install it on the side Spring lamination which won t install the drain hose 4 Extend the drain hose from the other side and install it on the base by the drain hose frame 5 Install the back cover Remark In order to make sure of the correct of installation it is suggested to change the direction of the drain hose with our company serviceman Usage of the drain hose The drain hose shall drain smoothly 1 The height of the drain hose shall be less 2 Do not trample or press the drain hose than 10cm or the drainage will not be smooth and cost such long time that the machine may stop at mid way 4 If extra drain hose is needed please make separate purchase The inner 3 diameter2. Confirm the operation of reserve program When the RESERVE function is activated the indicator light of the program you have set will be off The RESERVE HOURS and REMAIN MINUTES indicator lights will be on During reserve procedure push the RESERVE button to display the reserve mode To change the running program or cancel the reserve setting you need to switch off the power and make new selection The washing will finish about 18 hours later D Push bil button close the top lid Ifthe top cover is opened when the machine is spinning the machine will stop running and alarm 6 Finish washing After Finishing washing it will switch off power automatically 12 Disposal after washing Please first pull off the power plug from the receptacle before cleaning After using please clean the lint and foreign materials of the lint filter and overflow filter in time Otherwise it may influence your using the machine Clean the detergent box and set it onthe control panel seat 1 The method of 2 The method of install dismantle Push it up install it upwards and aslant and gently aslant and push it in Ny Dismantle Install Cleaning the lint filter 1 Push down the spring 5 Up 2 Pull the back of the lint The back v cS l Ba Be Install a of lint filter i ie pa lint ee Pa D w and a heen eter ey o make the claws out o Sante get down it off the fron ce Sf
3. Open and close The top Lid Once Close the top lid clear the E2 alarm please close the top cover and press the START PAUSE button Then E2 alarm will be cleared Reorder the laundries Close the top lid The machine will start running after 10 seconds of being placed horizontally Open the water tap Push the start Pause button once Clean the water inlet valve then push the start Pause button once Use after the water pressure is normal Please contact the after sales service department Please use it when there s power supply Insert the power plug tightly Fill water to the preset position Insert the power plug tightly Close the top lid Set the laundries flat Adjust the machine to be even Reorder the laundries and close the top lid Remove the foreign materials Fasten the jointer properly Common phenomena Phenomena The spinning is intermittent when it starts Push the spin button to select Spin but it doesn t work The final spinning is finished it becomes rinsing and begins to inlet water When the power plug is inserted computer board indicator is switched on and the machine starts working Specification Rated voltage Frequency Water level Water quantity about Injection pressure Washing Spinning capacity Explanation Balance the laundries to avoid slanting The program is setting the drain time Some time is needed before it starts
4. the filter cover and then i cover of the lint filter notes Install pull out the lint filter to AN P Sweep the rubbish in the The font cover get it down lint filter of lint filter Put the back of the lint filter into the front cover 3 Put the lint filter into filter 4 Make sure the lint filter cover and make it tight well installed or it can influence your use The filter screen of the water inlet valve is likely to be blocked by foreign materials and influence the water inlet Please clean it with brush every two months If the cabinet is dirty wipe it with wet cloth Do not flush it directly with water Wipe it with neutral detergent Do not wipe it with thinner petrol alcohol etc After washing close the water faucet If needed you can dismantle the water inlet hose Do not store water in the washing machine for a long period Drain the water completely after each using Be sure to pull off the power plug before maintenance Hang up the power cord Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid 13 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale
5. After installation the threading is 2mm above the upper surface of the nut See to Figure 6 Figure 5 Figure 6 About 4mm before twisting About less than 2mm after twisting Connection between the water inlet hose and the washer 1 Do not take off the water absorption cushion Please check if the cushion is dropped or damaged before nut of the water each usage If it happens please contact our inlet hose after sale department immediately 2 Put the nut of the water inlet hose on the valve Pam Ig jointer jointer of the water absorption water inlet valve Cushion 3 Fasten the nut Swing it gently to confirm if it s suitable Connection between the jointer of the water inlet hose and the water inlet hose WN 1 Push down the slider Insert the water inlet hose pase ee ees sa into the jointer 2 Hang the lock lever to the jointer Release the slider till a click sound is heard Check the connection between the jointer of the water inlet hose and the water faucet 1 Swing the hose gently to confirm if it is fastened stable 2 After installation open the faucet to check if it leaks 3 Do not bend the hose with overstrain 4 Before each usage please check if the connection between the jointer of the water inlet hose and the water faucet and 7 g the installation of the water inlet hose are firm so as to d 6 prevent dropping from improper installation position Dismantle the water inlet hose
6. fuzzy detection The computer will set the water level and wash time as per the cloth and quantity of the laundries The whole procedure is under automatic control POOH O SEH EEO E EEE ESET EOE EEE EEEEEEEEEEEE EEE EEEEHE EES OEEEHELETEEE DESEO EELEOESEDESELELELOCE Pe eee eee eres ee ee eee Ee OEE EEO LETHE LEECH EDEO EEE LOLOL ELEDELEE HELLO EEEEOLEEEELELEEEEELECOEEELOCS Posthaste wash of the laundry under 2 0 ikg with light soil The water level will automatically set 24L Just run the washing cycle without drainage cycle The detergent was left Remove the left detergent from the clothes and then rinse the clothes When the clothes are washed or the clothes are quite wet extra spin is needed TUB DRY The purpose is drying the inner tub and ithe outer tub which can avoid growing _ _ Steps of using the operation buttons 1 Push button to switch on the power 2 Push button to select suitable automatic program After the power is switched on SOAK is automatically set To select other fully auto program please push the PROGRAM button till the corresponding indicator is on Refer to the Program button on Page 8 When the soak is selected after the water start to jet the program wash rinse and spin will be implemented low water level soak for 25 minutes mid level 35 mins high level 45 mins Push PROGRAM button for 8 times and it will
7. hole Cabinet handle Screw cover right ae Drain entrance cover 2 pieces C Adjustable foot film 2 pieces Screw cover left Water inlet valve Back control board Power line a Si lt n A TN Back cover Drain hose Fixed foot 2 pieces Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the bottom plate After you open the package please lean the washing machine gently down on soft Front items like the towel cloth blanket ect Install the bottom plate to the bottom of the machine then lift the machine up Back gently See to the figure Soft items DA EERI E Bottom plate Two claws at the bottom cover shall p be inserted in two bar shaped holes in the stand Make sure the claws are firmly in place Section enlarging Fasten the bottom plate to base frame with one screw Adjust the Installation position The washing machine away from wall should be overrun 20mm The largest allowable slope of the shank base of the machine is 2 The slanting or rough ground will result in unstable running or stoppage of the machine Please adjust it with following methods Confirm it s horizontal Hang the lead line to check if it is horizontal Adjust the adjustable foot To twist the adjustable foot please first lift up the si
8. of the extra hose shall not If the drain hose is too long cut it at mid less than 30mm and the length shall point To make smooth drainage cut the front not exceed 1 5m end of the hose slantingly 5 If the extra hose is too long cut it either at A or at B point Preparation before washing Connect the water inlet hose Open the water faucet Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle The earth terminal shall not link to gas pipeline and faucet water pipeline Put down the drain hose Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention to followings before washing the laundries Confirm if there is special requirement for the laundries E Clear the pocket Take out the coins sand hairpins etc Pi _ Tie the long strips fasten the buttons close zippers The quantity of the laundries shall not be too large Stretch and loosen the lt gt laundries before putting them in the tub RR When the pulsator is running the buttons of the laundries may cause noise 3 For the sake of discretion please put the laundries with buttons into other ES laundries Check if the laundries are applicable for washing with machine e Please repair the damaged cloth before washing in order to avoid the situation worse Divide the laundries that are not colorfast from other
9. resume the intial mode It will circulate sequence Water pressure and water level influence the wash time Even there s no water in the tub the spinning will start after a certain period Wash and spin after putting the damageable clothes into tuck net to avoid scathe Wash the laundries that are prone to lose colors separately from other laundries When washing start or opening cover intermitting the washing machine will begin to work after a period time this is normal phenomenon Only select RINSE program If there s water inside the tub the machine will spin before rinsing If there s no water the machine will rinse directly 3 Push G button select suitable water level After switching on the power the washing machine will execute fuzzy program automatically to detect the cloth during the standard program After defection it can set the water level automatically To select other water level first push the START PAUSE button then push the WATER LEVEL button to set the water level The pulsator will not rotate unless the water is filled to selected water level 4 Push button to select suitable reserve wash program After switching on the power the reserve program is set to off mode automatically If you need to set the washing procedure to be finished at reserved time please push the RESERVE button to set the reserve wash program Refer to reserve button in Page 8 for selection
10. spinning Because the washing clothes lean to one side the safety switch acts After water filling and running eliminating the eccentricity of washing clothes then beginning to spin It is the special resume function In the case of power failure or the power plug is loose during washing the machine can save the running program and resume the program afterthe power supply is recobered You do not need to set the program again 220 240V 50Hz 1 12L 2 18L 3 24L 4 30L 5 35L 6 40L 7 45L 8 50L 0 03 MPa 1 0 MPa 7 5kg 7 5kg Haier 15
11. During operation of wash and rinse program you can push down the water level button to add water When you release the button or it reaches the overflow water level the machine will stop adding water The water level decided may be different from actual value because of the different moisture level of the laundries e After the and g REMAIN MINUTES FLASH 451 O 50L 351 O 40L 241 O 30L RESERVE HOURS 12 Ous RO ue a RESERVE Program Push the On Off button to switch on the power When the power is on push it again to switch off the power Push the On Off button to switch on the power If the start pause button is not pushed the washing machine will automatically switch off the power after 5 minutes the machine During working push it to pause During pause push this button to restart WATER LEVEL EE EE EE EE E E E e e e eeeeeaeneneeeneeneeenen7eeee eee eG 8 Oe Applicable situation Washing the relatively big thick or very Description of the function of buttons Off On indicate the program about to run or indicate the selected mode or indicate the water level O Flashing indicate the running program power is switched on press it to start o on working LIGHT wasHO Beye I an STANDARD ruzzv 2 CO sort POWER ON OFF PROGRAM dirty laundries STANDARD Common washing If STANDARD program is set the machine will execute
12. Haier User s Manual Fully Automatic Washing Machine Index e Safety precautions o Packing list e Names of the parts e Installation and adjustment e Preparation before WaShing aicnsspencemacciearenine cane e Use the operation buttons e Disposal after washing e Trouble shooting Answer to GUC SHON iicncreaaceanacnanaaananeea This manual is for Specification HWM75 7288 Please read this manual carefully before using Retain it for future reference Safety precautions Meaning and description of the symbols Contents marked with that symbol are related to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user WARNING Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of the user FORBIDDING Please check if power receptacle has good earthing condition before using to guarantee your safety Please check if the water faucet is open and if the connection of the water inlet pipe is proper itis suggested to use foamless washing powder Please don t use the washer in the environment below 0 C if the washer has been stored below 0 C please be sure to ensure the washer is plac
13. de of the foot slightly and then you can twist the two adjustable feet Please make sure to keep the washing machine in balance High Low T CL 14 a The adjustable foot Install the water inlet hose Confirm the water faucet It is required that the front end shall be longer than 10mm The exit end face of the faucet shall be flat and smooth If not please file it to avoid leakage water faucet suitable water faucet not suitable The exit end face of the faucet Connection between the water inlet hose jointer and the water faucet water inlet hose jointer 1 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 Slider 2 Loosen the screw till the water faucet can be accessed Put the jointer of the water inlet hose on the faucet See to Figure 2 If the faucet is too large and the jointer can not be set on the water faucet please loosen the four screws and take out the bushing in the jointer The front end of the faucet must be smooth otherwise it may leak water See to Figure 3 peace oot i te 3 Fasten the four screws evenly See to Figure 4 4 Take off the nameplate Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet See to Figure 5 Remark Before installation the threading is 4mm above the upper surface of the nut
14. ed under the room temperature more than 2 hours and then use otherwise the washing effects may be lowered or the washer may be damaged Please insert the power cord into special receptacle with rated voltage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector The washing machine must be positioned so that the plug is accessible Be sure to pull the plug off and close the water faucet in following cases power failure delivering the machine setting the machine idle or cleaning the machine Do not plug or pull the power plug with wet hand Do not bend extend twist bind by force Do not press or nip it with weight Keep the pin of the power plug clean if the power plug is polluted with dust please wipe with dry cloth carefully If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard Do not let the machine share one receptacle with other electric appliances If the plugging into the receptacles loose do not use the plug any more O O O O O O O O O O In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet Ensure carpet does not obstruct the opening in the bases Do not put the machine at damp place like the bathroom Never wash it with water Do not put
15. laundries e Put those laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil For those laundries that may get lint ball and those with long fur turn it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly e The foreign materials will result in damage of the machine 10 Put in the laundries Putin the laundries J T The capacity of washing and spinning of he machine refer to the largest weight ofthe standard laundries under dry conditionthat can be washed or spinned in one time One time washing quantity shall be lower than the rated capacity The thickness size type of the cloth will influence the actual washing capacity It is suitable for one time washing to put in reasonable amount of laundries and the laundries can be turned round in washing Do not select the high water level for laundries less than 1 0kg so as to avoid splashing of water Usage of the detergent How to use the washing powder and Softner Directly dissolved in the machine not applicable for fuzzy program 1 Fill small quantity of water 2 Add the powder Run for 30 seconds to dissolve it completely 3 Put it in the laundries Select suitable water level The instant dissol
16. or the usage and quantity of the whitener For powder whitener please dissolve it before using Use the operation buttons Coeeeeeee 0080080088088 88 0080 0 a O It displays during detecting It displays total remained time during the running program min It displays remained reserved time during reserve program hour It displays abnormal symbol in abnormal situation See to Page 11 The digitron displays the time remained in minute before the washing is finished Push down the reserve button The reserve indicator light is on the digitron displays the reserve time of finishing washing in hour When the machine is started the reserve indicator light is on indicating that the reserve function is running The washing machine can detect the laundries automatically during After detection it will set the water level to suitable value among 30L 40L 50L automatically during the STANDARD program You can also set water level by yourself After the machine is started it will not set water level automatically You shall push the start pause button to make new setting If there s water inside the tub the machine cannot detect the laundries and will display water level 40L If wet laundries are put in it may display water level 50L You must set suitable water level by yourself If quick program is selected it will display water level 24L If tub dry program is selected the water level will not respond
17. service department of our company Do not repair it by yourself Close the top lid Phenomenan 14 The digitron displays EO The drainage cannot work or is too slow The digitron displays E1 It stops running in midway The digitron displays E2 The safety switch acts and the spinning cannot work The digitron displays E3 The water filling does not work or is slow the digital displays E4 The digitron displays E6 The Not wash machine does not act Not spin There s abnormal sound inside the machine The water tap leaks The top lid is opened during reserve procedure Is the drain hose blocked The top lid is not closed When using the child lock function if the top cover is opened the machine will stop and display E2 alarm After 15 minutes the machine will automatic drainage Are the laundries put slantingly Is the machine slanting Is the water tap opened or is there water supply failure Is the water inlet valve blocked Is the water pressure too low The water level sensor is bad Is there power failure Is the power plug inserted tightly Is the water level reached preset position Is the power plug inserted tightly Is the top lid closed reliably Are the laundries set flat Is the machine slanting Are the laundries put slantingly in spinning Are there any foreign materials Is the jointer of water inlet hose loose or awry Clean the foreign material
18. ving of the washing powder 1 Prepare warm water of 30 C and a container 2 Add the powder while stirring to fully dissolve it The super quick program it is suggested to adopt liquid detergent instead of washing powder to guarantee the washing effect Put in the proper quantities detergent according to the water level and the laundries quantities It is suggested not to use high sudsing detergent Washing powder with poor quality or long time storage maybe caked Please pay attention to cleaning the detergent box in time Access for detergent How to use the softener Detergent box The usage and dose of the softener as per the specifications of softener Turn the inner tub you will find a softener inlet as the figure 1 open Rowe the cover put the softener into the inlet as the figure 2 Before washing close the cover and the softener will drop into the inner tub during the last time rinsing Control panel seat Figure 1 lt Liquid whitener inlet After the softener is put in please don t place for a long time otherwise softener may solidify and cause Figure 2 flowing not smooth Open Close How to use the whitener Fill water to decided level Dilute the whitener with container Pour it slowly into thewashing tub Avoid using whitener on laundries with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly Refer to the user s manual f
19. wet laundries on the control panel Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning Wash the clothes that can float on the water surface easily please be careful especially for fear damage Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials Such as thinner petrol etc The children shall not approach the working washing machine Keep the machine away from direct sunlight and heat source like the heater Do not decompose repair or alter the machine by yourself Do not use water hotter than 50 C Packing list Fully automatic washing machine Water inlet hose A M E Bottom plate Tapping screws User s manual One Package Warranty card Names of the parts Top lid Detergent box Control panel seat Outer tub cover Lint filter 2 pieces Balance ring Inner tub Filter cover 2 pieces Pulsator Control panel film Cabinet Adjustable foot 2 pieces Water absorption cushion All illustrations in this Manual are given for reference only Your products and accessories may show differences from these illustrations due to our continuous improvement Liquid whitener inlet Hanging
Download Pdf Manuals
Related Search