Haier Washer HW70-B1486-F User's Manual
Contents
1. AUTOMATIC DRUM WASHING MACHINE USER MANUAL HW O B 406 F HW 0 B1206 F HW80 B 1486 F HW80 B1286 F ABLE OF CONTENTS BEFORE USE USING THE APPLIANCE gt COMPONENTS 03 gt PROGRAM SELECTION 10 gt DISPLAY CODES gt PREPARATION wow 04 gt CONSUMPTION AND TECHNICAL DATA 11 gt SAFETY INSTRUCTIONS 05 gt WASHING METHODS 12 PINSTALLATION 06 CLEANING amp CARE 16 gt CONTROL PANEL 08 LEGEND lV Yes A No Optional AN For your safety any instructions in this manual with this Warning sign must be followed strictly COMPONENTS THANKS FOR PURCHASING A HAIER PRODUCT Please read these instructions caretully before using this appliance The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation use and maintenance Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance If you sell the appliance give it away or leave it behind when you move house make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings ACCESSORIES Check the accessories and literature in accordance with this list 1x Inlet hose assembly 1x Bottom Cover 1x User manual 1x D2. C i HDI Z mon MOA Aw a Optional 2 Detergent compartment Recommended Laundry Cotton fabrics Woolen fabrics Cotton fabrics Cotton or synthetic Chemical fiber fabrics Cotton fabrics Cotton fabrics Sports wear Cotton or synthetic Jeans Cotton or synthetic None 1 Detergent compartment for prewash mode 3 Compartment for softener and other additives Preset spin speed 800 rpm 600 rpm 800 rpm 1000 rpm 1000 rpm 1000 rpm 1000 rpm 800 rpm 800 rpm 1000 rpm 1000 rpm 1000 rpm CONSUMPTION TABLE MAX LOAD PROGRAM HW70 86 F HW80 86 F Hand Wash 2kg 2 kg Wool 2kg 2 kg Delicate 2kg 2 kg Mix 5kg 5 kg Synthetic 3 5kg 4 kg Cotton 7kg 8 kg Daily Wash 3 5kg 4 kg Sport 25 3 5kg 4 kg Express 15 2kg 2 kg Jeans 3 5kg 4 kg Baby Care 3 5kg 4 kg Spin Drain SPIN DRYING PERFORMANCE TEMPERATURE WASHING TIME vi vocc 11486 30 C 0 38 30 C 0 35 30 C 0 38 40 C Auto 40 C Auto 2 60 C Auto 53 51 40 C 0 4 30 C 0 25 c 0 15 40 C 0 58 2 30 C F33 0 08 The standard 60 C and 40 C cotton programmes are suitable to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined energy and water consumptions for washing that type of cotton laundry The actual water temperature may differ from the declared cycle temperature TECHNICAL DATA Power source Max working current A Water pressure
3. a sink unit In the event of a water leak allow the machine to dry naturally Place the washing machine directly on a carpet or close to a wall or furniture DO NOT VA Touch the washer door during the washing process it ets hot ya Place heavy objects or sources of heat or damp on top of the appliance Hot wash foam rubber or sponge like materials Open the detergent distribution drawer during the wash cycle a Force the washer door open The door is fitted with a self lock device and will open shortly after the washing procedure is ended Open the washer door if the water level is visibly over the porthole y Cover the washing machine with plastic cover so that inside dampness cannot be kept in INSTALLATION ADJUSTING THE BOTTOM COVER Before removing the transportation bolts please fix the bottom cover to the bottom of the washing machine Lay down the machine tig 1 screw off the teet and adjust the bottom cover with the four holes corresponding the screw holes of the feet Then screw the feet back on through the cover and fix it thus securely to the bottom of the machine fig 2 It keeps out the dampness and reduces the noise DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti vibration components inside of the washing machine during the transportation process Remove the back cover 2
4. drain hose is not in water The drain hose is in water Err Motor error Contact the maintenance personnel Err8 Water exceeds protective level Contact the maintenance personnel Er10 The signal of Water level sensor is wrong _ Contact the maintenance personnel EuAr The PBC and the motor cant t communicate _ Contact the maintenance personnel End End of wash cycle 1 25 he remaining time is hour 25 minutes 19 30 Status information Preset time for delayed operation UNb After the last rinsing cycle finishes spinning fails completely due to unbalance of the laundry Control panel lock function Press the Delay and the Start Pause buttons simultaneously for 3 seconds after starting a program It can no longer be changed by operating buttons or knobs To unlock press the Delay and Start Pause buttons again for 3 seconds Power off memory function In case of abrupt power failure or the need to cut off the power during a program cycle the present settings will be saved and the preset operation will resume when the power is on again To cancel a program Press the Start Pause button then switch off the power and the program is automatically cancelled Turn the program selector again to choose another program Note During the spin process if too much foam is inspected in order to protect the motor the washing machine will eliminate the foam automatically the motor will stop and the drain pump will drai
5. than normal 2 The foam may overflow from the detergent drawer because of the increasing pressure of the foam 3 It may remain foam without cleaning out after the final spinning cycle Recommendation 1 Clean the detergent drawer once a week 2 When using the prewashing program please add half of the rating dosage 3 Please follow the dosage recommendation on the powder or liquid detergent package ADDING DETERGENT Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments Push back the drawer gently Refer to the instructions on the drawer Caution For prewashing program detergent should be added to both compartments 1 and 2 For other programs do not add detergent to compartment 1 3 Add liquid detergent to the main drawer and dilute it first if it is concentrated Do not overuse detergent otherwise it will damage the artificial fibers so please follow the instructions on the detergent package Do not use liquid detergent if the pre wash mode or End delay is selected Do not overuse softener otherwise it will damage the artificial fibers SELECTING PROGRAM To get the best washing results an appropriate washing program should be 3 ES n selected according to the laundry type Please turn the program knob to 9 EM ie Es 9 Wool om FY Care select the right program EM 86 ZEE a OOOO O SELECTING FUNCTIONAL Select the req
6. the main washing stage of selected program This feature is applicable for dirty clothes The illuminated icon indicates the strong wash function is selected This additional function applies to cotton memory synthetic Silent heavy and Sport wash programs only This button is effective before starting a program Press the Delay button and the illuminated icon indicates that the delay function is selected The delay time 0 5 24h increases by 30 minutes each press of Delay button The time will change continuously if you press and hold this button until you release it The delay time is the end time of washing For example 6 00 means the washing ends after 6 hours the delay time must be longer than the program s running time The Delay function is not available for Spin and Self clean programs Note The delay time must be longer than the program time otherwise the washing machine will start the wash program directly Press the Pre wash button to select or cancel the prewash program The prewash program can be selected for washing heavily soiled clothes Press the Prewash button the Pre wash icon will illuminate Press the Pre wash again the prewash function will be cancelled and the Pre wash icon will go out When selecting the prewash function add a proper amount of detergent into the prewash box otherwise do not add any detergent into the prewash box This additional func
7. MPa Nominal load kg Spinning speed r min Washing programs Max power W Dimensions HxDxW mm Net weight kg Power consumption of the off mode W Power consumption of the left on mode W HW70 B1286 F HW70 B1486 F 220 240V S0Hz 10 0 03 lt P lt 1200 1400 12 2000 850 X 600 X 595 70 0 39 0 39 HW80 B1286 F HW80 B1486 F 220 240V S0Hz 10 0 03 lt P lt 8 1200 1400 12 2000 850 X 650 X 595 74 0 37 0 37 ASHING METHODS This washing machine is tor domestic use only If the machine is use for commercial purpose the guarantee will not be valid anymore Do not use it for purposes other than that for which it was designed Follow the instructions given on the label of each garment and wash only machine washable garments POWER SUPPLY Connect the washing machine to the power supply 220V to 240V 50Hz WATER CONNECTION Turn on the tap The water must be clean and clear Note Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap PREPARING THE LAUNDRY Sort out clothes according to fabric cotton synthetics wool or silk and to how dirty they are Separate white clothes trom coloured ones Wash them first by hand to check if they fade or run Empty pockets clips coins keys etc and remove the harder decorative objects e g brooches to avoid them entrying the drain pump and blocking Attention Small parts like button
8. Remove the four bolts on the rear side and take out the synthetic stabilisers from within the machine 3 Replace the back cover 4 Fill the holes left by the bolts with blanking plugs Note 1 When you replace the back cover the convexity must face to outside and you have to insert the back cover from the two gaps as shown in fig 5 2 Keep the transportation bolts and synthetic stabilisers in a safe place for later use ADJUSTING THE WASHING MACHINE There are adjustable feet under the bottom of the washing machine Before use they should be adjusted so that the machine is level This will minimise vibrations and thus noise during use It will also reduce wear and tear We recommend using a spirit level to level the appliance The floor should be as stable and flat as possible INLET HOSE 1 Connect the nut on the inlet hose to the connector on the water valve 2 Apply inlet hose to a water tap with cold fresh water Note Use the hose set supplied with the appliance Old hose sets should not be reused DRAIN HOSE 1 Use the drain hose bracket to keep the end of the drain hose retained and prevent the outtlow of water Don t extend the length of the drain hose if an extended hose is required please consult a serviceman 80 100cm 2 The height of the drainage outlet must be 80 100 cm Fix the drain hose to the clip at the back of the washing machine to prevent it trom dropping oft Boe ae aa a nn Not
9. add clothes during washing or want to remove clothes due to extended power failure make sure Pull pol that the water level in the drum is properly below the lower edge of sight glass the water temperature is below 50 C and the inner drum is not running then remove the drain pipe from its support and lower it until no water is drained from the drain pipe replace the drain pipe Open the filter door at the bottom Em of the washer and you will see a pull pole Take out the pull wire and gently pull it downwards until you hear a low sound the door will open now you can add or remove the clothes Afterwards reset the pull pole and filter door CARE CHART VY Resistant material X27 Delicate fabric Washable at 95 C Washable at 60 C Washable at 40 C Washable at 30 C d Hand wash IF Dry clean only Wool Seal LOAD REFERENCE Bed sheet single Blanket Blended fabric clothes Jackets Jeans Overalls Ladies Pyjamas Shirts Socks T Shirts Underwear eO Bi BI BID PP Cotton Wool Cotton Cotton Blended fabrics Cotton Blended fabrics Bleachable in cold water Do not bleach X Don t dry clean Dry flat Iron at 200 C m Hung to dry Iron at 150 C Dry on clothes hanger Iron at 100 C C Tumble dry normal heat Don t iron Tumble dry reduced heat Dry cleaning with any solvent Dry cleaning with pericloride Dry cleaning with aviation fuel Don t tumble dry Approxima
10. e The drain hose should not be submerged in water and should be securely fixed and leak free If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm the washing machine will continuously drain while being filled self siphoning CONNECTING TO THE POWER SUPPLY Before connecting to the power supply check The socket is adequate for the maximum power of the washing machine For safety fuses in the power circuit should be rated for no less than 154 The voltage should meet the requirement The power outlet should be capable of accepting the washing machine plug Connect the machine to an earthed socket outlet CONTROL PANEL A Power Switch F Display screen K intense washing button B Program knob G Washing time L End Delay Button C Memo button H Times of rinse M Pre wash button D Spinning Speed Setting button Spinning time N Rinse Hold button E Washing temperature button J Detergent distribution drawer 0 Start Pause button OPERATIONAL FUNCTIONS A Power _ Press this button to switch on the washing machine Press it again to switch it off Press On Off button gently for Switch 2 seconds to switch off the machine as buttons are soft touch sensitive The End sign will appear on the display after finishing the program It will change to power off station if there is no operation on the button and none will be shown B Program _By turning the knob clockwise counterclockwise the re
11. e 4 Fax 49 0 6172 94 54 499 D 61352 Bad Homburg Mail into de haiereurope com Haier
12. he water inlet valve and inlet valve filter regularly MOVING THE MACHINE If the machine is to be moved to a distant location replace the transportation bolts removed before installation to prevent damage as shown below Remove the back cover Remove the blanking plugs Insert the synthetic stabilisers and the transportation bolts Tighten the bolts with a spanner Replace the back cover vo N LONG PERIODS OF DISUSE If the washing machine is left idle for a long period pull out the electrical plug and turn oft the water supply Open the washer door to prevent formation of moisture and odours Let the door open while not used DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Err Door is not properly shut _ Shut the door properly and then press the Start Pause button Err2 Drainage error water not emptied within 6 Clean the filter and check the drain hose for blockage If error minutes still exists please contact the maintenance personnel Err3 Temperature sensor not properly connected or _ Contact the maintenance personnel damaged Err4 Heater error Appears at the end of a cycle Contact the maintenance personnel Err5 Water level not met in 8 minutes Make sure that tap is turned on and water pressure is normal If problem still exists please contact the maintenance personnel e e _ Install drain hose within 80 100 cm of height D Make sure the
13. ly The inlet hose filter is blocked Unblock the inlet hose filter The height of the drain hose is below 80 cm Install drain hose within 80 100 cm of height The drain hose is in water Make sure the drain hose is not in water Drain hose is blocked Unblock the drain hose Drain hose end is higher than 100 cm above Make sure the drain hose end is lower than the floor level 100 cm above floor level The filter is blocked Unblock the filter Not all transportation bolts have been removed _ Remove all transportation bolts Washing machine is located on an uneven _ Make sure the washing machine is on surtace or is not level an even surtace and levelled Machine load is over Max load Reduce amount of laundry in the drum Water or electricity failure _ Check the power supply Washing machine gives an error message Check display codes Washing machine is in soaking cycle _ Press the rinse hood button or the Start pause button again to cancel it The detergent is not a low foaming type or for __ Check if your detergent is appropriate manual wash _ Reduce amount of detergent in the distribution Excessive use of detergent drawer The washing program duration will be adjusted _ This is normal and doesn t affect the functionality Unbalance of the laundry _ Add clothes or run a spinning program again Haier Deutschland GmbH Tel 49 0 6172 94 54 0 Hewlett Packard Stra
14. n the water continuously for 90 seconds If it happens more than 3 times the motor will stop until the end of cycle without spinning TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems Do not contact the Service Center until the problem has been contirmed PROBLEM Washing machine fails to operate Washing machine cannot be filled with water Machine is draining while being filled Drainage failure Strong vibration while spinning Operation stops before completing wash cycle Operation stops for a period of time Excessive foam in the drum which is spilled to the distribution drawer Automatic adjustment of the washing time Spinning fails CAUSES SOLUTIONS Poor connection to the power supply _ Check connection to the power supply Power failure Check the power supply The washer door is not properly closed lose the washer door properly Machine has not been switched on _ Make sure the machine is switched on The Start Pause button is not pressed _ press the Start Pause button Water tap is not turned on _ Turn on the water tap Water pressure is less than 0 03 Mpa _ Check water pressure The inlet hose is kinked Check the inlet hose Water supply failure Ensure the water supply The program knob is not properly set _ Set the program knob properly The washer door is not properly closed lose the washer door proper
15. o select heating temperature 30 40 50 60 90 The maximum allowable temperature heating temperature varies with programs button Note in the temperature display indicates non heated washing F Display screen G Washing time H Times of rinse Spinning time Detergent distribution drawer K Intense wash ing button L End Delay Button M Pre wash button N Rinse Hold button 0 Start Pause Button Display washing time remaining time times of rinsing spinning time temperature setting value speed setting value child lock state door lock state washing progress and alarm message etc Press the Wash button to set washing time Press and hold this button to change the time continuously Click this button up until the end Note This function is not applicable to Spin Drain process Press the Rinse button to select the times of rinsing and the maximum allowable times of rinsing is 8 Press the Spin button to select spinning time The maximum allowable spinning time varies with programs Open the drawer three compartments can be seen Compartment 1 Prewash detergent Compartment 2 Detergent for programs 1 to 10 Compartment 3 Softener conditioning agent perfume etc The recommendation on the type of detergents is suitable for the various washing temperatures please refer to the manual of detergent Press Strong wash button to increase the washing time during
16. quired program can be selected There are 12 programs knob available After a program is selected the corresponding light will go on a Om This function could be used under the programmes cotton Synthetic Mix After choosing one of these the user can set washing time washing temperature rinse times spin speed spin time and choose some additional function such as Intense Delay Prewash Rinse hold according as her need or habit Finish them then keep pressing memo button for 2 seconds the display screen will show the corresponding number 1 stands for the programme have been setting under cotton 2 stands for the programme having been setting under synthetic 3 stands for the programme having been setting under Mix It means the programme choosing by users have been saved Next time when user choose one of these Cotton Synthetic Mix then press Memo the corresponding programme having been saved will be called out press Start pause button to perform this programme Also the setting programme can be used many times until the user set a new one the previous programme will be covered D Spinning _ Press the Speed button to select spinning speed The maximum allowable spinning speed varies with Speed Set programs ting Button Note Different water temperatures and spinning speeds can be set for different laundries Wash using the default settings if there is no special requirement E Washing _ Press the Temp button t
17. rain hose bracket 4x Blanking plugs PREPARATION PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness including the polystyrene base Upon opening the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water tests in the factory DESCRIPTION This diagram may be slightly different from the layout of the washing machine you have just purchased due to technical improvements Control panel Drain hose Power Water inlet valve Work top Washer door Power cord Door handle Back cover screws Detergent distribution drawer Back cover Filter cover Transportation bolts SAFETY INSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME DO V Make sure that the transport bolt are removed M Usea separate earthed socket for the power supply V Make sure that the plug is accessible V Hold the plug and not the electric cable when unplugging the power supply Make sure that the fuses in the power circuit are rated for 15A Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging Make sure that the power cord is not caught under or in the appliance and avoid damage to the power cable Check that hose joints and connections are firm and no water can leak If joints are loose or there is leakage turn off the wa
18. s etc may lead to repair work which user has to pay by themselves and can cause damage in the machine Garments without hems underwear finely woven textile such as fine curtains are to be put into wash bag it is better not to wash them in a washing machine lose zippers and hooks make sure the buttons are sewn on tightly and place small items such as socks belts bras etc in the wash bag Untold large pieces of fabric such as bed sheets bedspreads etc Turn shirts inside out LOADING THE MACHINE Open the washer door put in the laundry piece by piece Close the door tightly When first using the washing machine let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine Before washing you should run the machine without laundry but with detergent with 60 C programm Do not overload the washing machine SELECTING DETERGENT 3 a The washing efficiency and the performance is determined by the quality of detergent used Special non foaming detergent produces good washing results Use specific detergents for synthetic and woollen goods Do not use dry cleaning agents such as trichloroethylene and similar products Note Do not add more detergent than needed otherwise it may cause the situations as following and wash ing machine malfunction impacting washing machine s life 1 Due to the increasing foam the rinse time will be longer
19. tely 800g Approximately 3000g Approximately 800g Approximately 800g Approximately 800g Approximately 950g Approximately 200g Approximately 300g Approximately 50g Approximately 300g Approximately 70g CLEANING amp CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash Open the washer door to prevent formation of moisture and odours If the washing machine is left idle for a long period drain the water in the machine and replace the drain hose CLEANING THE DETERGENT DRAWER Clean the detergent distribution drawer regularly Swing out the drawer flush it clean with water and then replace it CLEANING THE MACHINE Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soap liquid to clean the machine case and rubber components Do not use organic chemicals or corrosive solvents CLEANING THE FILTER Clean the filter once a month 1 Open the bottom cover 2 Remove the filter by turning counterclockwise 3 Flush the filter clean with running water 4 Replace the filter by turning clockwise and remount the cover Caution 1 The filter must be in place or it may lead to leakage 2 Place a container under the drain pump filter to collect any excess water that may come out of the drain pump when the filter is removed WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of foreign substances clean t
20. ter supply and refix Do not use the washing machine until the hoses are properly fixed DURING DAILY USE OF THE APPLIANCE DO V Pul up zips and fix loose threads to prevent the items from being entangled If necessary put small items into a net bag or pillow V Tum off the machine after each wash program and switch it otf at the mains to save electricity and for satety Wipe clean the lower part of the porthole Keep the door slightly open when the washing machine is not in use to prevent formation of odours Let the power cord be replaced by the manutacturer his service agent or other accordingly qualified persons in case it is damaged V Ensure that the appliance is not used by persons with reduced physical sensory or mental capabilities lack of experience and knowledge without supervision or instruction by a person responsible for their safety MI Supervise children to ensure that they do not play with the appliance DO NOT VA louch or use the appliance when barefoot or with wet or damp hands or feet Use flammable detergent or dry cleaning agent Use any flammable sprays in dose vicinity to the appliance Remove or insert the plug in the presence of flammable as VA Allow children or infirm persons to play with the appliance or packing materials Z Install the appliance outdoors in a damp place or in an area which may be prone to water leaks such as under or near
21. tion applies to cotton memory synthetic and Sport wash programs only Press Rinse Hold button to startup shutdown the crease resistant and soak function When the process runs to the last rinse the washing machine is not going to drain clothes will be soaked in water and the soak icon flashes the remain time not decreasing If you need to continue the process you can press Rinse Hold button or start pause button then the icon will be off to cancel this function and the washing machine continue to work This feature and the End Delay button can not be chose at the same time Also this feature is only effective in the cotton synthetic Delicate Sport 25 Jeans process _ Press the Start pause button the washer will start and the indicator light remains on If this button is pressed when the washer is in operation the washer will pause and the indicator light will flash PROGRAM SELECTION PROGRAM MODES Program 2 Hand Wash Wool Delicate Mix Synthetic Cotton Daily Wash 3 Sport 25 Express 15 Jeans Baby Care Spin Drain V Yes lemperature Maximum to 40 C to 40 C 10 40 C to 40 C to 60 C to 90 C to 60 C to 40 C 10 40 C to 60 C to 90 C IV No Preset 2 93 x MO mon x MO 40 C lV C C 40 C lV u u mon 40 C v V 30 C lV
22. uired options Refer to the Control panel pages 08 and 09 SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected See Opera tional functions on the Control panel pages 08 and 09 for selecting temperature and spin speed It is advisable to select the recommended value WASHING Press the Start Pause button The washing machine will operate according to the preset programs The washing machine will stop operation automatically when a washing cycle ends The End sign will appear on the display Open the washer door and take out the laundry AFTER WASHING Turn off the water supply and unplug the power cord Open the washer door to prevent formation of moisture and odours Let the door open while not used TIPS FOR SAVING ENERGY Collect clothes for one full wash load Avoid overloading the washing machine Prewash only heavily soiled clothes Reduce the amount of detergent or choose standard or delicate wash programs for slightly soiled clothes Choose a proper washing temperature Modern detergents can wash with very good result already in lower temperature than 60 C Only use higher temperature than 60 C for heavily soiled laundry 6 Follow the dosage recommendation on the detergent package to avoid using too much detergent WARM TIPS vr gt om To
Download Pdf Manuals
Related Search