Haier Compact Air Conditioner User's Manual
Contents
1. 2 If the power supply cord is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person 3 If the fuse of indoor unit on PC board is broken please change it with the type of T 3 15A 250V If the fuse of outdoor unit is broken change it with the type of T 25A 250V 4 The wiring method should be in line with the local wiring standard 5 After installation the power plug should be easily reached 6 The waste battery should be disposed properly Haier Air Conditioner Cautions Safety Instruction e Please read the following Safety Instructions carefully prior to use e The instructions are classified into two levels WARNING and CAUTION according to the seriousness of possible risks and damages as follows Compliance to the instructions are strictly required for safety use Installation A WARNING Edition 2006 1 10 Please call Sales Service Shop for the Installation Do not attempt to install the air conditioner by yourself because improper works may cause electric shock fire water leakage Installation in a inadequate place may cause accidents Do not install in the following place A CAUTION Connect the earth Do not install in the place where there is any possibility of inflammable gas leakage around the unit S PROHIBITION 10 Do not get the unit exposed to vapor or oil steam S PROHIBITION Che2. Load the battery 5 v i Be sure that the loading is in line with the request as illustrated on the bottom of the case Put on the cover again Confirmation indicator After pressing power ON OFF if no display reload the batteries Note e Full display or unclear display during operation indicates the batteries have been used up Please change batteries Used two new same typed batteries when loading e f the remote controller can t run normally during operation please remove the batteries and reload several minutes later Hint Remove the batteries in case unit won t be in usage for a long period If there are any display after taking out just need to press reset key 14 il f a I e Air Conditioner Edition 2006 1 10 Operation HEALTH operation Remote controller 1 Unit start Press ON OFF on the remote controller unit starts Health function includes health anion function UV light degerming function 2 Health anion function Press HEALTH button For each press gg is displayed Air conditioner starts health anion function operation For twice press disappears the operation stops When indoor fan motor is running it has healthy process function It s available under any mode When the fan in the indoor unit does not work the health lamp lights up but the anion generator does not release anion BRIEF INTRODUCTION TO HEALTH ANION FUCTION The anion genera
3. PROHIBITION Do not pour water onto the unit for cleaning PROHIBITION Do not place flower vase or water containers on the top of the unit PROHIBITION il f a I e Air Conditioner Edition 2006 1 10 Parts and Functions Ga nonor anil D OPERATE COOL DRY HEAT TIMER HEALTH Display board seem ts ae RED GREEN YELLOW The conversion of pilot light s colors will be displayed as the figure under different operation models Display board net Air filter inside Anion generator inside Inlet grille Vertical flap Use remote controller to adjust up and down air flow Don t adjust it manually Horizontal louver adjust left and right air flow r unit gt Oueso aa OUTLET CONNECTING PIPING AND ELECTRICAL WIRING INLET 4 DRAIN HOSE 12 Haier Air Conditioner Edition 2006 1 10 Parts and Functions L 65 mO e ASBB MBBS 3 o CSO a O o c e TET o J 1 CODE Used to select CODE A or B with a press A or B will be displayed on LCD Please select A without special explanation 2 RESET When the remote controller appears abnormal use a sharp pointed article to press this button to rese
4. S SLEEP operation starts SLEEP operation stops Approx 6hrs Temp setting Unit stop In COOL DRY mode 2 In HEAT mode 1 hours after SLEEP mode starts temp will become 2 C lower than temp setting After another 1 hours temp decrease by 2 C further After more another 3 hours temp rises by 1 C further The unit will run for further 3 hours then stops Temp is lower than temp setting so that room temperature won t be too high for your sleep Temp setting SSRises 1 C SLEEP SLEEP operation starts operation stops In HEAT mode 3 In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode 4 In FAN mode It has no SLEEP function 5 Set the wind speed change when sleeping If the wind speed is high or middle before setting for the sleep set for lowing the wind speed after sleeping If it is low wind no change Note When TIMER function is set the sleeping function can t be set up After the sleeping function is set up if user resets TIMER function the sleeping function will be cancelled the machine will be in the state of timing on 22 il f a I e Air Conditioner Edition 2006 1 10 Operation Timer On Off Operation Set clock correctly before starting TIMER operation Remote Controller 1 After unit starts select your desired operation mode 2 Timer mode selection Press TIMER button to chang
5. e Incomplete earthing may cause an electric shock EARTHING HRA N D ID NO WET HAND 4 Plug in A Caution e After brush away dust at the plug insert the plug of the power supply cord into the outlet completely In case of suing exclusive circuit breaker switch on the circuit breaker 32
6. Operation Cool Operation p Ba Remote controller 1 Unit start _ Press ON OFF on the remote controller unit starts 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller k b 3 AUTO COOL DRY FAN HEAT Then Select COOL operation 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting increase 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decrease 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller peat eat eat tl LOW MED HI AUTO Air conditioner is running under displayed fan speed When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature 5 Unit stop Press ON OFF button the unit stops 17 il f a I e Air Conditioner Edition 2006 1 10 Operation Dry Operation Remote controller 1 Unit start Press ON OFF on the remote controller unit starts 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller gt kX T AUTO COOL DRY FAN HEAT Then Select DRY operation 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting in
7. as follows Remote controller III gt gt EN Waa BLANK e0G ien 200 TIMER ON TIMER OFF TIMER ON OFF Then select your desired TIMER mode TIMER ON OFF will flash 3 Time setting Press HOUR AV V button A Every time the button is pressed time setting increases 1 min if kept depressed it will increase rapidly V Every time the button is pressed time setting decreases 1 min if kept depressed it will decrease rapidly It can be adjusted within 24 hours 4 Timer confirming for TIMER ON After setting correct time press TIMER button to confirm EM on the remote controller stops flashing fi starts flashing Time displayed Unit starts or stops at x hour x min 5 Time setting for TIMER OFF Just press HOUR button follow the same procedure in Time setting for TIMER ON 6 Time confirming for TIMER OFF After time setting press SET button to confirm tga on the remote controller stops blinking Time displayed Unit stops at x hour x min To cancel TIMER mode Just press TIMER button several times until TIMER de disappears According to the Time setting sequence of TIMER ON or TIMER OFF either Start Stop or Stop Start can be achieved 24 Haier Air Conditioner Edition 2006 1 10 Operation POWERISOFT Operation Remote controller Ju at Oy POWER Operation When you need rapid heating or cooling you can use this function Selec
8. 1 Pos 2 al Pos 3 Pos 4 A A Pos 5 7 Pos 6 Auto swing z 2 Up and down air flow direction For each press of lt gt button air flow direction on remote controller displays as follows according to different operation modes COOL DRY FAN remote controller Pos 1 Pos 2 Pos 3 gt Pos 4 Pos 6 HEAT remote controller Pos 5 Pos 4 Pos 3 Pos 2 Pos 1 Pos 6 AUTO remote controller Pos 1 Pos 2 Pos 3 gt Pos 4 Pos 5 Pos 6 The vertical flap will swing according to the above positions Note When restart after remote turning off the remote controller will automatically memorize the previous set swing position 21 Haier Operation Sleep Operation Before going to bed you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep Use of SLEEP function After the unit starts set the operation status then press SLEEP button before which the clock must be adjusted and time being set Operation Mode 1 In COOL DRY mode 1 hours after SLEEP mode starts temp will become 1 C higher than temp setting After another 1 hours temp rises by 1 C further The unit will run for further 6 hours then stops Temp is higher than temp setting so that room temperature won t be too low for your sleep Remote Controller Air Conditioner Edition 2006 1 10
9. button of health airflow F appears on the display The nether inlet and outlet grills of the air condit ioner are closed and the airflow is blown horizontally from the above inlet and outlet grills Avoid the strong airflow blows direct to the body 2 Press the button of health airflow again appears on the display The above inlet and outlet grills of the air cond itioner are closed and the airflow is blown vertically from the nether inlet and outlet grills Avoid the strong airflow blows direct to the body 3 The cancel of the health airflow function Press the button of health airflow again both the inlet and outlet grills of the air conditioner are opened and the unit goes on working under the condition before the setting of health airflow function After stopping the outlet grille will close automatically Notice Cannot pull direct the outlet grille by hand Otherwise the grille will run incorrectly If the grille is not run correctly stop for a minute and then start adjusting by remote controller Note 1 After setting the health airflow function the position of inlet and outlet grills is fixed 2 In heating it is better to select the f mode 3 In cooling it is better to select the f mode 4 In cooling and dry using the air conditioner for a long time under the high air humidity a phenomenon falling drips of water occurs at the outlet grille 5 Select the appropriate fan direction according to the ac
10. ck proper installation of the drainage securely ENFORCEMENT Edition 2006 1 10 Haier Air Conditioner Cautions A WARNING When abnormality such as burnt small found immediately stop the operation button and Use an exclusive power source with a circuit breaker contact sales shop Connect power supply cord to the outlet completely STRICT ENFORCEMENT Do not use power supply cord in a bundle Do not start or stop the operation by disconnecting the power supply cord and so on o STRICT ENFORCEMENT Use the proper voltage STRICT ENFORCEMENT Take care not to damage the power supply cord PROHIBITION Do not channel the air flow directly at people especially at infants or AV ANN Do not use power supply cord extended or connected in halfway PROHIBITION Do not insert objects into the air inlet or outlet PROHIBITION Do not try to repair or reconstruct by yourself Do not use for the purpose of storage of food art work precise equipment breeding or cultivation c ti EP PROHIBITION Do not install the unit near a fireplace or other heating apparatus a 6 PROHIBITION Do not place animals or plants in the direct path of the air flow PROHIBITION STRICT Check good condition of the installation stand S PROHIBITION Do not place any objects on or climb on the unit PROHIBITION 11
11. crease 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decrease 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller peat eat atl ttl LOW MED HI AUTO Air conditioner is running under displayed fan speed In DRY mode when room temperature becomes Ultra low air flow 5 lower than temp setting 2 C unit will run intermittently Cee at LOW speed regardless of FAN setting 5 Unit stop On reaching temp setting ce Press ON OFF button the unit stops COOL operation starts when room temp is higher than temp setting Temp setting 2 C Temp setting unit will run in mild DRY mode il f a I e Air Conditioner Edition 2006 1 10 Operation Fan Operation 1 Unit start Press ON OFF on the remote controller unit starts Remote controller 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller i gt b 69 3 AUTO COOL DRY FAN HEAT Then Select FAN operation 3 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller ui suil sul ul LOW MED HI 4 Unit stop Press ON OFF button the unit stops About FAN operation In FAN operation mode the unit will not operate in COOL
12. e TIMER mode Every time the button is pressed display changes as follows Remote controller ego ienn 200 i TIMER ON TIMER OFF TIMER ON OFF Then select your desired TIMER mode TIMER ON or TIMER OFF EA or fd will flash 3 Time setting Press HOUR A V button A Every time the button is pressed time setting increases 1 min if kept depressed it will increase rapidly V Every time the button is pressed time setting decreases 1 min if kept depressed it will decrease rapidly It can be adjusted within 24 hours 4 Confirming your setting After setting correct time press SET button to confirm MH or Ed on the remote controller stops flashing Time displayed Unit starts or stops at x hour x min TIMER ON or TIMER OFF 5 Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears Hints After replacing batteries or a power failure happens time setting should be reset Remote controller possesses memory function when use TIMER mode next time just press SET button after mode selecting if time setting is the same as previous one 23 B Hi a e Air Conditioner Edition 2006 1 10 O tion Timer On Off Operation Set clock correctly before starting TIMER operation Remote Controller 1 After unit starts select your desired operation mode 2 Timer mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes
13. e by pulling it upward 2 Remove the filter Push up the filter s center tab slightly until it is released from the stopper and remove the filter downward 3 Clean the filter Use a vacuum cleaner to remove dust or wash the filter with water After washing dry the filter completely in the shade 4 Attach the filter Attach the filter correctly so that the FRONT indication is facing to the front Make sure that the filter is completely fixed behind the stopper lf the right and left filters are not attached correctly that may cause defects 5 Close the inlet grille 29 il f a I e Air Conditioner Edition 2006 1 10 Maintenance Replancement of Air Purifying Filter IER the Inlet Grille Open the inlet grille by pushing each ends of the inlet grille upward use thumbs to push up 2 Detach the standard air filter Slide the knob slightly upward to release the filter then withdraw it 3 Detach old Air Purifying Filter 4 Attach old Air Purifying Filter Put air purifying filter appliances into the right and left filter frames LION LN ar 5 Attach the standard air filter Necessary installation 6 Close the Inlet Grille Close the Grille surely NOTE e The air purifying filter of the bacteria killing medium and the electrostatic air purifying filter accessories with machine will be used based o
14. er Edition 2006 1 10 Maintenance For Smart Use of The Air Conditioner Setting of proper room Do not block the air inlet or outlet temperature P a E T5 a Close doors and windows Use the timer effectively during operation XII AAD ID During cooling operation prevent the penetration of direct sunlight with curtain or blind If the unit is not to be used for a long time turn off the power supply main switch L 28 il f a I e Air Conditioner Edition 2006 1 10 Maintenance For Smart Use of The Air Conditioner A WARNING Before maintenance be sure to turn off the system and the circuit breaker Indoor Body Remote Controller Wipe the air conditioner by using a soft and dry cloth For serious stains use a neutral detergent diluted with water Wring the water out of the cloth before wiping then wipe off the detergent completely Do not use water wipe the controller with a dry cloth Do not use glass cleaner or chemical cloth Hot water over 40 C 104 F may cause Gasoline benzine thinner or cleanser may A discoloring or deformation damage the coating of the unit Air Filter cleaning 1 Open the inlet grill
15. he name and address of the waste materials collecting centers and waste paper disposal services nearest to your house Air Conditioner Edition 2006 1 10 Safety Instructions and Warnings Before starting the air conditioner read the information given in the User s Guide caref ully The User s Guide contains very impor tant observations relating to the assembly operation and maintenance of the air conditioner The manufacturer does not accept respon sibility for any damages that may arise due to non observation of the following instruction e Damaged air conditioners are not to be put into operation In case of doubt consult your supplier e Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User s Guide e Installation shall be done by professional people don t install unit by yourself e For the purpose of the safety the air con ditioner must be properly grounded in acco rdance with specifications e Always remember to unplug the air conditioner before openning inlet grill Never unplug your air conditioner by pulling on the power cord Always grip plug firmly and pull straight out from the outlet e All electrical repairs must be carried out by qualified electricians Inadequate repairs may result in a major source of danger for the user of the air conditioner e Do not damage any parts of the air conditioner that carry refrigerant by pierc
16. il iml a i Air Conditioner Edition 2006 1 10 OPERRATION Haier Cautions Disposal of the old air conditioner Before disposing an old air conditioner that hoes out of use please make sure it s inop erative and safe Unplug the air conditioner in order to avoid the risk of child entrapment It must be noticed that air conditioner system contains refrigerants which require speciali zed waste disposal The valuable materials contained in an air conditioner can be recycled Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question Please ensure that the pipework of your air conditioner does not get damaged prior to being picked up by the relevant waste disposal center and contribute to environmental awareness by insisting on an appropriate anti pollution method of disposal Disposal of the packaging of your new air conditioner All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service The wrapping bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon All these valuable materials may be taken to a waste collecting center and used again after adequate recycling Consult your local authorities for t
17. ing or perforating the air conditioner s tubes with sharp or pointed items crushing or twisting any tubes or scraping the coatings off the surfaces If the refrigerant spurts out and gets into eyes it may result in serious eye injuries il f a I e Air Conditioner Edition 2006 1 10 Cautions Do not obstruct or cover the ventilation 7 The appliance is not intended for use grille of the air conditoner Do not put fingers by young children or infirm persons or any other things into the inlet outlet and without supervision swing louver 8 Young children should be supervised e Do not allow children to play with the air to ensure that they do not play with conditioner In no case should children be the applience allowed to sit on the outdoor unit 9 Please employ the proper power plug which fit into the power supply cord Specifications 10 The power plug and connecting cable e The refrigerating circuit is leak proof must have acquired the local attestation The machine is adaptive in following 11 In order to protect the units please turn Situation off the A C first and at least 30 seconds 1 Applicable ambient temperature range later cutting off the power Maximum D B W B 32 C 23 C Indoor Minimum D B W B 18 C 14 C Cooling Maximum D B W B 43 C 26 C Outdoor Maximum D B 18 C Maximum D B 27 C Maximum D B 15 C Maximum D B W B 24 C 18 C Minimum D B W B 15 C Indoor Heating Outdoor
18. n real situation e The bacteria killing medium air purifying filter is available for a long time and needn t to be changed But it must be noticed to use the vacuum cleaner frequently to adsorb the dusts covering the purifying filter lest the covering dusts effect the function of the bacteria killing medium air purifying filter It is strictly prohibited for the bacteria killing medium air purifying filter to be washed e The green aspect of the bacteria killing medium air purifying filter will face outside the white aspect will face to the machine and the white side of the electrostatic air purifying filter will face outside 30 a I e Air Conditioner Edition 2006 1 10 Maintenance To Keep Your Air conditioner in Good Condition after Season 1 Operate in cooling mode for 2 3 hours To prevent breeding mold or bad smell be sure to operate at the designated temperature or 30 C cooling mode and High speed fan mode for 2 3 hours 2 Put off the power supply cord 3 Cleaning the body 4 Take out the batteries from the wireless remote controller 31 il f a I e Air Conditioner Edition 2006 1 10 Maintenance Before Setting in High season 1 Cleaning the standard air filter Operation without filter may cause troubles Be sure to attach both right and left filters prior to the operation Each of them are of different shapes 2 Connecting the earthing cable A Caution
19. or HEAT mode but only in FAN mode AUTO is not available in FAN mode And temp setting is disabled In FAN mode SLEEP operation is not available 19 il f a I e Air Conditioner Edition 2006 1 10 Operation sui Operation ae 1 Unit start aa ma Press ON OFF on the remote controller unit starts q Kenii controller A 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN HEAT Then Select HEAT operation 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting increase 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decrease 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller F EET suil suil p LOW MED HI AUTO Air conditioner is running under displayed fan speed IN HEAT mode warm air will blow out after a short period of the time due to cold draft prevention function When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature 5 Unit stop Press ON OFF button the unit stops 20 il i a I e Air Conditioner Edition 2006 1 10 Operation Air Flow Direction Adjustment 1 Status display of air sending Vertical flap Pos
20. s Press it once again lock will be cancelled and lock condition display disappears NOTE The following functions and related displays are not available 13 il i a I e Air Conditioner Edition 2006 1 10 Parts and Functions E Clock Set When unit is started for the first time and after replacing batteries in SASE remote controller clock should be adjusted as follows es 1 Press CLOCK button AM or PM flashes 2 Press A or to set correct time Each press will increase or decrease CS wl 1 min If the button is kept depressed time will change quickly 3 After time setting is confirmed press SET AM or PM stop flashing oe Ha S while clock starts working E Remote controller s operation When in use put the signal transmission head directly to the receiver hole on the indoor unit eThe distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well Don t throw or knock the remoter controller When electronic started type fluorescent lamp or change over type fluorescent lamp or wireless telephone is installed in the room the receiver is apt to be disturbed in receiving the signals so the distance to the indoor unit should be shorter E Loading of the battery Load the batteries as illustrated right 2 R 03 7 batteries Remove the battery cover Slightly press area and push down the cover as illustrated
21. t the remote controller normal 3 LIGHT button Control the lightening and extinguishing of the indoor LED display board 4 TIMER button Used to select TIMER ON TIMER OFF TIMER ON OFF 5 CLOCK button Used to set correct time 6 HEALTH button Used to set healthy operation 7 MODE button Vk b O i AUTO COOL DRY FAN HEAT 8 HOUR button Used to set clock and timer setting 9 SWING button Used to select up or down air sending direction 10 ON OFF button Used for unit start and stop 11 TIMER ON display 12 FAN SPEED display gal sail all LOW MED HI AUTO 13 LOCK display 14 SWING UP DOWN display 15 SLEEP display 16 HEALTH display 17 Operation mode display Operation mode AUTO COOL DRY FAN HEAT Remote controller 7 3 3 18 Singal sending display 19 POWER SOFT display 20 Left right air flow display 21 TEMP display Remote controller to display the TEMP setting 22 TIMER OFF display 23 CLOCK display 24 TEMP button Used to select your desired temperature 25 FAN button Used to select fan speed LOW MED HI AUTO 26 HEALTH AIRFLOW button Used to set the health airflow mode 27 SLEEP button Used to select sleep mode 28 SET button Used to confirm timer and clock settings 29 POWER SOFT button Use to set power soft function 30 LOCK Used to lock buttons and LCD display If pressed the other buttons will be disabled and the lock condition display appear
22. ting of POWER operation Press POWER SOFT button Every time the button is pressed display changes as follows i f N BLANK POWER SOFT Stop the display at In POWER operation status In COOL mode wind speed automatically takes high wind of AUTO wind mode In HEAT mode wind speed automatically takes medial wind of AUTO wind mode To cancel POWER operation Press POWER SOFT button twice POWER SOFT disappears SOFT Operation You can use this function when silence is needed for rest or reading Selecting of SOFT operation Press POWER SOFT button Every time the button is pressed display changes as follows 9 7 N BLANK POWER SOFT Stop the display at In SOFT operation mode wind speed automatically takes low wind of AUTO wind mode To cancel SOFT operation Press POWER SOFT button again POWER SOFT disappears Hints During POWER operation in rapid HEAT or COOL mode the room will show inhomogeneous temperature distribution Long period SOFT operation will cause effect of not too cool or not too warm 25 igl am a i e Air Conditioner Edition 2006 1 10 Operation Health airflow Operation 1 Press ON OFF to starting Rem ntroller The liguid crystal will display the working state of last time Except timer sleeping power soft and health airflow Setting the comfort work conditions 2 The setting of health airflow function 1 Press the
23. tor in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room 15 il f a I e Air Conditioner Edition 2006 1 10 Operation Auto Operation R t fall 1 Unit start emete controll Press ON OFF on the remote controller unit starts 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller ioe a ered AUTO COOL DRY FAN HEAT Then Select Auto operation 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting increase 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decrease 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller EI BA I cast o Air conditioner is running under displayed fan speed When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature 5 Unit stop Press ON OFF button the unit stops About Auto Operation Under the mode of auto operation air conditioner will automatically select Cool or Heat operation according to room temperature 16 il f a I e Air Conditioner Edition 2006 1 10
24. tual conditions 26 il f a I e Air Conditioner Edition 2006 1 10 Operation Emergency and Test Operation Emergency operation e Use this operation only when the remote controller is defective or lost e When the emergency operation switch is pressed the Pi sound is heard once which means the start of this operation e In this operation the system automatically selects the operation modes cooling or heating according to the room temperature e When machine is running in emergency the set value of temperature and wind speed couldn t be altered meanwhile it can t operate for dehumidifying or under timing mode Test operation Test operation switch is the same as emergency switch e Use this switch in the test operation when the room temperature is below 160C do not use it in the normal operation J e Continue to press the test operation switch for more J than 5 seconds After you hear the Pi sound twice release your finger from the switch the cooling operation starts with the air flow speed Hi Removal of the restriction of emergency or test operation e Press the emergency operation switch once more or manipulate through the remote controller the Pi sound the emergency or test operation is terminated e When the remote controller is manipulated it gets the system back to the normal operation mode 2 il f a I e Air Condition
Download Pdf Manuals
Related Search