Greenheck Fan CSP-B User's Manual
Contents
1. Refrigeration and Air Conditioning proper height is determined shown in arranged to adapt Engineers ASHRAE and the local code authorities Fig 5 For fan and fan light combination to most mounting ba diti When cutting or drilling into wall or ceiling do not opening cut a 14 4 by 11 inch holein oS damage electrical wiring or other hidden utilities the ceiling For fan CRD combination gS Acceptable for use over a bathtub or shower when opening cut a 14 by 12 inch hole in the installed in a GFCI protected branch circuit Up ceiling Fig 5 through size SP A390 Never place a switch where it can be reached from a Fig 6 2 Tighten For Frame Construction Position unit tub or shower E a between joists Position brackets such am Ducted fans must always be vented to the outdoors l Ceiling that bottom edge of housing will be flush with finished ceiling and tighten the These fans are not recommended for cooking exhaust adiustable applications They are designed primarily for low 1 Adjust to be flush J temperature clean air applications only The diagram with finished ceiling mounting brackets shows the minimum distance these fans should be shown in Fig 6 placed in relation to cooking equipment Fan Light combination not to be installed in a ceiling For Hanging Installations Use Greenheck s thermally insulated to a value greater than R40 optional vibration isolator kit Part Number VI CAUTION Kit Using the f2. which have an oil hole provided A few drops of all purpose oil SAE 20 will be sufficient Warranty Greenheck warrants this equipment to be free from defects in material and workmanship for a period of three years from the purchase date Any units or parts which prove to be defective during the warranty period will be replaced at our option when returned to our factory transportation prepaid Greenheck will not be responsible for any installation or removal costs GREENHECK SP CSP models shown are SP B amp CSP B IOM FS PRO BOX 410 EGET 54476 0410 C UL US UL and cUL listed E 33599 Rev 8 March 2004 www greenheck com Copyright 2004 Greenheck Fan Corp
3. READ AND SAVE THESE INSTRUCTIONS A GREENHECK Model SPB Building Value in Air Ceiling Exhaust and Inline Fans Installation Operation and Maintenance Manual Prepare the Fan 1 If power assembly motor and wheel is not installed in housing insert ae the electrical plug into fan socket then slide wheel end of power J es 4 assembly into fan housing and rotate clockwise until it is positioned ey under tabs Align the holes and attach by using two sheet metal a screws provided shown in Fig 1 3 A gs D KOSS Ceiling Radiation Damper CRD VW NNN 1 If fan is to be used in a fire resistive membrane ceiling a ceiling 5 radiation damper must be used Otherwise proceede to Install the Fan Fig F 2 If the ceiling radiation damper is already mounted to the fan from the factory Attachment Tabs proceed to Install the Fan 3 To mount the ceiling radiation damper to fan make sure grille WARNING attachment tabs are facing down Then place the inlet part of the z fan into the ceiling radiation damper collar and use self tapping To reduce the risk of fire electric shock or injury to sheet metal screws 10x 2 in by persons observe the following others to screw through the damper Suitable for use with solid state speed controls collar and into the fan housing shown in Use this unit only in the manner intended by the Fig 2 If the fan light combination is being manufacturer If you ha
4. an s standard adjustable mounting brackets and 10 by 32 threaded For general ventilating use only Do not use to exhaust ea 9 2 y rod by others hang unit as shown in Fig 7 hazardous or explosive materials and vapors Installation Recommendations Install the Fan continued 3 Slide ductwork over the fan s discharge collar and securely attach it with sheet metal screws Make sure the screws do not interfere with damper operation Check damper to make sure it opens freely Wire the Fan 1 Remove wiring cover If fan light combination is being used make sure the fan plug is connected to the fan receptacle and the light plug is connected to the light receptacle shown in Fig 8 Using proper wire connectors wire the fan as shown in Fig 9a For wiring of light proceed to Fig 9b 115 amp 277 Volt Black wire is Hot White wire is Neutral Green wire is Ground 220 240 Volt Black wire is Hot White wire is Hot 2 Push all wiring into the unit s cover and replace wiring cover Green wire is Neutral Ground Attach the Grille 1 If lighted grille is being used plug wire into fan socket If lighted grille and ceiling radiation damper are being used plug wire from lighted grille into ceiling radiation damper socket Do not plug wire directly into the fan socket Make sure the wire does not interfere with the ceiling radiation damper operation 2 Attach grille with two scr
5. ews provided Make sure not to over tighten over tightening will damage grille 3 Slide attachment screw covers over the attachment screws shown in Fig 10 4 If lighted grille is being used install light bulb s into light socket s For incandescent lights use maximum 100 watt bulb by others For fluorescent lights use only Greenheck s Part Number 382854 provided 13 watt flicker resistant light bulbs For replacement bulbs please contact Greenheck at phone number 1 800 355 5354 Squeeze tabsto JW Fig 11 insert remove lens 5 If lighted grille is being used snap lens into place by pushing on the outside edges of lens shown in Fig 11 To remove lens use small screw driver and pry on one side of lens 6 Turn on power and check fan and light operation General Maintenance Suggestions Model SP CSP ceiling exhaust fans require very little maintenance But since small problems over time left unchecked could lead to loss of performance or early motor failure we do recommend that the unit be inspected periodically once or twice a year The fan motor and wheel should be checked for dust and dirt accumulations Dirt buildup can lead to loss of performance and motor overheating Cleaning can be accomplished by brushing off any dust that may have accumulated Even filtered units can accumulate build up and should be checked when cleaning filters The motor should be checked for lubrication at this time Lubricate only those motors
6. ve questions contact the used make sure ceiling radiation damper Wires to ceiling fan manufacturer has an electrical plug in it The electrical Before servicing or cleaning unit switch power off at plug must be inserted into the fan Make We service panel and lock service disconnecting means to sure the electrical wire will not interfere with A prevent power from being switched on accidentally damper operation shown in Fig 3 i f this area When the service disconnecting means cannot be Wires from lighted grille locked securely fasten a prominent warning device such as a tag to the service panel Install the Fan Installation work and electrical wiring must be done by 1 For best performance choose a Veeco li accordo ne wiin eil abellcane location with the shortest possible duct codes and standards including fire rated construction one i el See aren en 4 run and minimum number of elbows Do ufficient air is needed for proper combustion an not mount near cooking equipment shown NRY exhausting of gases through the flue chimney of fuel in Fig 4 g equip a burning equipment to prevent back drafting Follow the g 4 Fig 4 heating equipment manufacturer s guideline and safety standards such as those published by the National Fire 2 Attach adjustable mounting brackets to Protection Association NFPA and the American fan but leave the screws loose until Brackets can be Society for Heating
Download Pdf Manuals
Related Search