Graco 3A2090C User's Manual
Contents
1. 4 3A2090C Operation Warnings PRESSURIZED ALUMINUM PARTS HAZARD Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture Failure to follow this warning can result in death serious injury or property damage e Do not use 1 1 1 trichloroethane methylene chloride other halogenated hydrocarbon solvents or fluids con taining such solvents e Many other fluids may contain chemicals that can react with aluminum Contact your material supplier for com patibility ENTANGLEMENT HAZARD Rotating parts can cause serious injury e Keep clear of moving parts e Do not operate equipment with protective guards or covers removed e Do not wear loose clothing jewelry or long hair while operating equipment e Equipment can start without warning Before checking moving or servicing equipment follow the Pressure Relief Procedure and disconnect all power sources MOVING PARTS HAZARD Moving parts can pinch cut or amputate fingers and other body parts Keep clear of moving parts Do not operate equipment with protective guards or covers removed Do not wear loose clothing jewelry or long hair while operating equipment Pressurized equipment can start without warning Before checking moving or servicing equipment follow the Pressure Relief Procedure and disconnect all power sources EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury Do2. 3A2090C Operation 5 Warnings BATTERY HAZARD The battery may leak explode cause burns or cause an explosion if mishandled Contents of an open battery can cause severe irritation and or chemical burns If on skin wash with soap and water If in eyes flush with water for at least 15 minutes and get immediate medical attention Only use the battery type specified for use with the equipment See Technical Data Battery maintenance must only be performed or supervised by personnel knowledgeable of batteries and the required precautions Keep unauthorized personnel away from battery Do not dispose of battery in fire The battery is capable of exploding Follow local ordinances and or regulations for disposal Do not open or mutilate the battery Released electrolyte has been known to be harmful to the skin and eyes and to be toxic Remove watches rings or other metal objects Only use tools with insulated handles Do not lay tools or metal parts on top of battery BURN HAZARD af Equipment surfaces and fluid that s heated can become very hot during operation To avoid severe burns e Do not touch hot fluid or equipment PERSONAL PROTECTIVE EQUIPMENT Wear appropriate protective equipment when in the work area to help prevent serious injury including eye injury hearing loss inhalation of toxic fumes and burns This protective equipment includes but is not limited to e Protective eyewear and hearing protection e Respirators prot
3. gasket contacts base 2 Fill with five quarts of Graco hydraulic oil 169236 5 gallon 20 liter or 207428 1 gallon 3 8 liter 3 Check oil level 3A2090C Operation 22 Hydraulic Oil Filter Change N NAS lt NG ti2271a 33 Technical Specifications Non PBS Technical Specifications Non PBS LineLazer IV 250SPS Models 24F307 24K960 24K961 24K962 24M608 Height with handle bar down Unpackaged 47 25 in Unpackaged 120 0 cm Packaged 54 25 in Packaged 137 8 cm Width Unpackaged 33 0 in Unpackaged 83 8 cm Packaged 40 0 in Packaged 101 6 cm Length with platform down Unpackaged 73 5 in Unpackaged 186 7 cm Packaged 78 0 in Packaged 198 1 cm Weight dry no paint Unpackaged 666 Ib Unpackaged 302 1 kg Packaged 769 Ib Packaged 348 8 kg Noise dBa Sound Power per ISO 3744 103 1 Sound Pressure measured at 3 1 feet 1m Vibration m s 8 hours daily exposure Whole Body per ISO 2631 Power Rating Horse Power Power Rating Horse Power per SAE J1349 11 9 HP 3600 rpm 8 8 KWO 3600 rpm Maximum Delivery 2 5 gpm 9 5 lpm Maximum Tip Size 1 gun 055 in tip 2 gun 039 in tip 3 gun 033 in tip Wetted Parts PTFE Nylon polyurethane V Max UHMWPE fluoroelastomer acetal leather tungsten carbide stainless steel chrome plating nickel plated carbon steel ceramic 00 gt Ae 34 3A2090C Operation Technical Specifications PBS T
4. Attach ground wire to true earth ground Perform Startup steps 1 6 see page 10 to flush out paint in sprayer Use water to flush water base paint and mineral spirits solvent also called white spirit to flush oil base paint Hold gun against paint bucket and pull trigger until water or solvent appears Move gun to solvent or water bucket Hold gun against bucket and pull trigger until the system is thoroughly flushed Y 7 h f o NY Fill pump with Pump Armor and reassemble filter guard and SwitchTip Each time you spray and store fill throat packing nut with TSL to decrease packing wear 3A2090C Operation Hydraulic Oil Filter Change Removal Di 1 i Alb H This equipment stays pressurized until pressure is manually relieved To help prevent serious injury from pressurized fluid such as skin injection splashing fluid and moving parts follow the Pressure Relief Procedure when you stop spraying and before cleaning checking or servicing the equipment ME LO od EE AKA e 1 Relieve pressure page 9 2 Place drip pan or rags under sprayer to catch hydraulic oil that drains out 3 Remove drain plug Allow hydraulic oil to drain 4 Unscrew filter 227 slowly oil runs into groove and drains out rear Installation 1 Apply a light film of oil on filter gasket Install drain plug and oil filter 227 Tighten oil filter 3 4 turn after
5. Control Overview Smart Control Overview Quick Guide MANUAL MODE s AUTO MODE CYCLE 40 0 0 mph psi 0 DISTANCE 0 GALLONS reset gt PAINT 10 0 JOB MIL 4 LINE gt SPACE 30 0 MEASURE AUTO MODE e to start gt gt PAINT SPACE lt lt measuring 10 0 30 0 hold to 8 0 24 0 apply dot 5 0 15 0 SELECT gt 3 0 12 0 CLEAR ALL gt 3 0 9 0 CALIBRATION amp UNITS to start TRAVEL DISTANCE 25 gt CHANGE UNITS gt ENGINE HOURS LIFE MILES LIFE GALLONS SOFTWARE REV NO STORED ERROR CODE MORE DATA 22 e PARKING LAYOUT MODE e psi 0 mph STALL SIZE 9 0 DOT SIZE PARKING CALC MEASURE to start measuring CALC STALLS STALL SIZE ANGLE CALC to change angle offset STALL DEPTH dot spacing STALL SIZE MARKER SELECT gt EDIT gt 3A2090C Operation Smart Control Operation Initial Setup 1 Select appropriate language gt gt ENG lt lt SPA FRE DEU OO ti19024a ENG English SPA Spanish FRE French DEU German NOTE Languages can also be changed later 2 Select appropriate units of measure gt gt US UNITS S I UNITS ti19025a US Units Pressure psi Volume gallons Distance feet Line Thickness mil Speed mph SI Units Pressure bar MPa available Volume liters Distance meters Line thickness micron g m available Speed Kph Paint Specific Gravity Use UP and
6. desired actuator rod ti18998a 5 Route cable around unit and up through cable holes behind hose mount 1 Select cable end with adjuster 2 Install exposed cable through cable bracket slot eS lt 6 Route cable end loop through rectangular hole in bracket and insert plastic cable retainer into the actuator bracket Install cable end onto actuator rod and install clip 16 3A2090C Operation Change Trigger Position Removal 1 Remove both hand grips from handle bar spraying 1 compressed air into end of handle grip works well for this ti18988a 2 Usean allen wrench to loosen bolt on trigger mount ing clamp ti18989a 3 Remove trigger assembly from handle bar ti18990a 3A2090C Operation Gun Placement Installation Route trigger wire to other side of handle bar Make sure wire is routed behind steering column through wire slot on steering plate and into wire clamp on handle bar ti18993a 2 Install trigger assembly onto desired handle bar clamp ti18992a 4 Replace hand grips ti19254a 17 18 Gun Placement Gun Positions Chart mls PS z PTE hes Epa sl One line up to 24 in 61 cm wide KAL o one guna Sem IS GN JA aly mall al rs A Par TI amica a 3 p ti18553a 3A2090C Operation Driving Instructions Drivi ng Instructions To turn ri
7. 2 Yes 2Tanks LLIV 250 SPS North America Latin America Asia Pacific 3A2090C Operation 3 Warnings Warnings The following warnings are for the setup use grounding maintenance and repair of this equipment The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure specific risks When these sym bols appear in the body of this manual or on warning labels refer back to these Warnings Product specific hazard sym bols and warnings not covered in this section may appear throughout the body of this manual where applicable o TRAFFIC HAZARD Va Being struck by other vehicles may result in serious injury or death NO e Do not operate in traffic e Use appropriate traffic control in all traffic areas e Follow local highway and transportation regulations for traffic control for example Manual on Uniform Traffic Control Devices U S Department of Transportation FIRE AND EXPLOSION HAZARD Flammable fumes such as solvent and paint fumes in work area can ignite or explode To help prevent fire and explosion Use equipment only in well ventilated area Do not fill fuel tank while engine is running or hot shut off engine and let it cool Fuel is flammable and can ignite or explode if spilled on hot surface Eliminate all ignition sources such as pilot lights cigarettes portable electric lamps and plastic drop cloths potential static arc Keep work area free of debris including solven
8. 5 lt lt eto start a measuring CLEAR ALL gt ti9942b ti18564a NOTE The last measured length is also saved as the length in PARKING CALC display NOTE Press and hold Gun Trigger Control at any time to apply a dot 3A2090C Operation Smart Control Operation Machine Information 1 Press SETUP button three times from Manual Mode display ti19107a t119108a ti19106a ENGINE HOURS LIFE DISTANCE LIFE GALLONS SOFTWARE REV NO STORED ERROR CODE MORE DATA 5 ti9918b 2 Press arrow keys to toggle between more data screens MORE DATA MODEL NUMBER ENGINE RPM 0 ENGINE HOURS 0 LIFE GALLONS 0 SOFTWARE REV 0 NO STORED ERROR CODE MORE DATA gt ti9933b ti9934b 31 Cleanup Cleanup AA Dina 2 This equipment stays pressurized until pressure is manually relieved To help prevent serious injury from pressurized fluid such as skin injection splashing fluid and moving parts follow the Pressure Relief Procedure when you stop spraying and before cleaning checking or servicing the equipment 1 Perform Pressure Relief Procedure page 9 2 Remove guard and SwitchTip from all guns TI3371A 3 Unscrew cap remove filter Assemble without filter 32 4 Clean filter guard and SwitchTip in flushing fluid Q TI3375A FLUSH Place siphon tube set in grounded metal pail par tially filled with flushing fluid
9. 5 ft 7 6 m distance ll 11 Push gun trigger control to complete calibration 26 Hana ti10022a ti18564a 12 NEW CALIBRATION STORED displays Press EXIT Calibration is now complete 13 Go to MEASURE mode and verify accuracy by measuring the tape see MEASURE MODE Calibration Error Displays This message is displayed if striper has rolled beyond calibration length when gun trigger control is pressed to end calibration CALIBRATION amp UNITS CALIBRATION FAILED COUNT TOO HIGH START AGAIN t19927a This message is displayed if striper has rolled less than calibration length when gun trigger control is pressed to end calibration CALIBRATION amp UNITS CALIBRATION FAILED COUNT TOO LOW START AGAIN EXIT ti9928a 3A2090C Operation Change Units or Language 1 Press SETUP twice to move to CALIBRATION amp UNITS display Select CHANGE UNITS ti19107a CALIBRATION amp UNITS e to start TRAVEL DISTANCE 25 gt CHANGE UNITS gt ti9926b 3A2090C Operation Smart Control Operation 2 While in CHANGE UNITS display press CHANGE to change units or NEXT to move to the next unit of measure Press SETUP to exit CHANGE UNITS mode CHANGE UNITS SETUP to exit ENGLISH QO CHANGE UNITS SETUP to exit PRESSURE po pal ct bar MPa CHANGE UNITS SETUP to exit VOLUME CHANGE UNITS SETUP to exit DISTA NCE CHANG
10. ARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise Graco Information For the latest information
11. DOWN arrows to set specific gravity Required to determine paint thickness NOTE All units can be changed individually at any time 3A2090C Operation Smart Control Operation Calibration 1 Check rear tire pressure 55 5 psi 379 34 Kpa and fill if necessary 2 Rotate calibration bar S J x oe gt e SF ti18713a 3 Insert calibration bar face down ti18714a ti18715a NJ 5 Extend steel tape to distance greater than 26 ft 8 SS tit8716a 25 tt 1 23 Smart Control Operation 6 Press SETUP twice to move to CALIBRATION amp UNITS display Set TRAVEL DISTANCE to 25 ft 7 6 m or longer Longer distances ensure better accuracy depending on conditions ti9915b t110296a CALIBRATION amp UNITS e to start TRAVEL DISTANCE CHANGE UNITS gt ti9926b 7 Align calibration bar rear edge with 1 foot 30 5 cm on steel tape FT Hobie ti10021a 1 la uhh 8 Push gun trigger control to start calibration ti18564a 9 Move striper forward Keep calibration bar over steel tape 24 10 Stop when calibration bar rear edge aligns with 26 ft 8 m on steel tape 2
12. E UNITS SETUP to exit METRIC LINE THICKNESS gt gt micron lt lt g sq meter ti18508a CHANGE UNITS SETUP to exit PAINT SPECIFIC GRAVITY CHANGE 5 ti18509a 25 Smart Control Operation Operation in Manual Mode Operation in Automatic Mode po Manual Mode 00 0 DISTANCE job 0 GALLONS reset gt JOB MIL 4 LINE ti9915b 1 Make sure engine is running and engine clutch switch is on 2 ti25622a 2 Use Gun Selector Switches to select guns and place switch in continuous line position Programmed line pattern 3 OFF position disengages gun 4 Continuous line ti18969a 3 Press and hold Gun Trigger Control button to spray a line Release button to stop spraying NOTE Selected guns will spray even if the striper is not 9 moving 26 i Preset Skip Patterns In the AUTOMATIC MODE the striper is equipped with Preset Skip Patterns To select a preset skip pattern press MODE button to move to AUTO MATIC MODE ti9915b Press SETUP button to view preset skip patterns ti9942b Use SELECT arrows to mark desired pattern Press SETUP key to save and return to AUTOMATIC MODE display Use Gun Selector Switches to select guns and line type Programmed line pattern OFF position disengages gun Continuous line ti18969a NOTE Striper must be moving for guns to activate With the striper moving faster than 0 3 mph 0 5 kph press Gun Trigger Control Button t
13. E t118548a NOTE Adjust screw for more or less braking force 3A2090C Operation 19 Driving Instructions Drive Engagement 3 If striper arcs to the left turn adjuster screw counter clockwise The wheel motor bypass valve allows the operator to disengage the wheel tension and push the unit around Rotate one complete turn counter clockwise to disengage 4 Test drive the striper Repeat steps 2 and 3 until striper drives straight Tighten two bolts on wheel alignment plate to lock the new wheel setting ti18576a Straight Line Adjustment The front wheel is set to center the unit and allow the Handle Bar Height Adjustment operator to form straight lines Over time the wheel may become misaligned and will need to be readjusted To re center the front wheel perform the following steps 1 Loosen handlebar height adjuster lock 1 Loosen two bolts on the wheel alignment plate ti18586a 2 l striper arcs to the right turn adjuster screw clockwise 3 Tighten handlebar height adjuster lock ti18585a ti18573a 20 3A2090C Operation Platform Storage Position 1 Raise stand and pin self locks ti18560a 2 To lower stand pull pin and lower stand ti18566a 3A2090C Operation Driving Instructions Front Pad Adjustment 1 Loosen four bolts 2 Slide pad up or down to desired position ti19006a 3 Tighten four bolts 21 Smart
14. Operation ES y GRACO LineLazer IV 250sps Self Propelled Line Striper 3A2090C For the application of line striping materials For professional use only For outdoor use only Not for use in hazardous locations or explosive atmospheres For Models see Page 3 Maximum Operating Speed 10 mph 16 kph Maximum Operating Pressure 3300 psi 22 8 MPa 228 bar Read all warnings and instructions in this manual and the engine manual Be familiar with the controls and the proper usage of the equipment Save these instructions B IMPORTANT SAFETY INSTRUCTIONS Related Manuals E AA PROVEN QUALITY LEADING TECHNOLOGY Table of Contents MOGEIS yess tee A da i 3 NVALIIINGS 6 2 Bsc cs ce nes tard dio AA A 4 Component Identification Sprayer 7 Component Identification Controls 8 Grounding Procedure For Flammable Materials Only 9 Pressure Relief Procedure 9 SeLUP SlaMUpP sitas E 10 SwitchTip and Guard Assembly 12 Gun Placement 0000 eee e eens 13 Install GUM e tercios ras NGA dia 13 Position GUN iks segera par Loge ee 13 Gun Arm Mounts o o oococoooooo o 14 Change Gun Position Front and Back 14 Change Gun Position Left and Right 14 Gun Cable Adjustment 16 Change Trigger Position 17 Gun Positions Chart o oo oooo o 18 Drivi
15. about Graco products visit www graco com For patent information see www graco com patents TO PLACE AN ORDER contact your Graco distributor or call 1 800 690 2894 to identify the nearest distributor All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice For patent information see www graco com patents Original instructions This manual contains English MM 3A2090 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 Copyright 2010 Graco Inc is registered to ISO 9001 www graco com Revision C January 2015
16. aco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS W
17. and moving parts follow the Pressure Relief Procedure when you stop spraying and before cleaning checking or servicing the equipment 1 Perform Grounding Procedure For Flammable Materials Only page 9 2 Fill throat packing nut with Throat Seal Liquid TSL to decrease packing wear 3 Check engine oil level Add SAE 10W 30 Summer or 5W 30 winter See engine manual ti3308a gt ti6470a 10 If removed install strainer G ti3430a Turn prime valve down Turn pressure control coun terclockwise to lowest pressure N iaraa ti3441a NOTE Minimum hose size allowable for proper sprayer operation is 3 8 in x 11 ft 9 5mm x 3 3m Place siphon tube set in grounded metal pail par tially filled with flushing fluid Attach ground wire to true earth ground Use water to flush water base paint and mineral spirits to flush oil base paint and storage oil ti18550a 3A2090C Operation Setup Startup 10 Start engine e After engine starts move choke to open a Move fuel valve to open LA 3312 ti18563a b Move choke to closed 11 Set engine clutch switch to ON ti25622a ti18561a c Set throttle to fast 12 Set pump valve ON pump is now active ti6471a 13 Set throttle to desired setting E START ti18568a 3A2090C Operation 11 Setup Startup 14 Increase pressure control enough to start pump 19 Trigger gun again into flushin
18. echnical Specifications PBS LineLazer IV 250SPS with Pressurized Bead System Models 16V470 16V471 16V473 16V474 24U561 Height with handle bar down Unpackaged 55 7 in Unpackaged 141 5 cm Packaged 63 5 in Packaged 161 3 cm Width Unpackaged 33 0 in Unpackaged 83 8 cm Packaged 45 0 in Packaged 114 3 cm Length with platform down Unpackaged 73 5 in Unpackaged 186 7 cm Packaged 78 0 in Packaged 198 1 cm Weight dry no paint Unpackaged 778 lb Unpackaged 352 9 kg Packaged 916 Ib Packaged 415 5 kg Noise dBa Sound Power per ISO 3744 105 9 Sound Pressure measured at 89 1 3 3 feet 1m Vibration m s 8 hours daily exposure Whole Body per ISO 2631 Power Rating Horse Power Power Rating Horse Power per SAE J1349 11 9 HP 3600 rpm 8 8 KWO 3600 rpm Maximum Delivery 2 5 gpm 9 5 lpm Maximum Tip Size 1 gun 055 in tip 1 gun 039 in tip 3 gun 033 in tip Wetted Parts PTFE Nylon polyurethane V Max UHMWPE fluoroelastomer acetal leather tungsten carbide stainless steel chrome plating nickel plated carbon steel ceramic 3A2090C Operation 35 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Gr
19. ective clothing and gloves as recommended by the fluid and solvent manufacturer CALIFORNIA PROPOSITION 65 The engine exhaust from this product contains a chemical known to the State of California to cause cancer birth defects or other reproductive harm This product contains a chemical known to the State of California to cause cancer birth defects or other reproductive harm Wash hands after handling 6 3A2090C Operation Component Identification Sprayer Component Identification Sprayer SERIAL PARINO aaa Operator Platform Paint Filter Prime Drain Valve Displacement Pump Rear Gun Arm Mount both sides Serial Label under operator platform Gun Trigger Lock 8 Front gun mount both sides Ez Wheel Motor Bypass Valve 3A2090C Operation Straight Line Adjuster 10 StaightLine Adjuster ooo Brake Steering Handle Adjustable Pad Component Identification Controls Component Identification Controls Engine Key Switch OFF ON START 2 Display 3 Forward Reverse Lever 4 Gun Trigger Control Engine Throttle KI Engine Choke 7 Gun 1 2 Selector Engine Clutch KI 12V Accessory Jack both sides Pressure Control Hydraulic Pump Valve 8 3A2090C Operation Grounding Procedure For Flammable Materials Only Awe This equipment must be grounded to reduce the risk of static sparking Static sparking can cause fum
20. es to ignite or explode Grounding provides an escape wire for the electric current 1 Position striper so that the tires are not on pave ment 2 Ground sprayer with grounding clamp Grounding clamp must attach to grounded object e g metal sign post ra I bo ka i ml a Ak e A fe oT CDN P ARMIN 1 C AFS EE MF lt o ti23146a 3A2090C Operation Grounding Procedure For Flammable Materials Only Pressure Relief Procedure Y E al AA Dina 2 This equipment stays pressurized until pressure is manually relieved To help prevent serious injury from pressurized fluid such as skin injection splashing fluid and moving parts follow the Pressure Relief Procedure when you stop spraying and before cleaning checking or servicing the equipment 1 Perform Grounding Procedure if using flammable materials 2 Set pump valve OFF Turn engine OFF ti6740a 3 Turn pressure control to lowest setting Trigger gun to relieve pressure gli ti3305a ti344ta GT PAINT 4 Engage gun trigger lock Turn prime valve down gt N SN NS ti6473a a ti3324a Setup Startup Setup Startup AA Dina 2 This equipment stays pressurized until pressure is manually relieved To help prevent serious injury from pressurized fluid such as skin injection splashing fluid
21. g fluid pail until paint Allow fluid to circulate for 15 seconds appears Assemble tip and guard 15 SEC ti3442a 15 Turn pressure down turn prime valve horizontal Disengage gun trigger lock ti6472a N 5 w 20 Repeat step 19 on second gun for 2 gun models yy soa SwitchTip and Guard Assembly ti344ia TS 16 Hold gun against grounded metal flushing pail Trig ger gun and increase fluid pressure slowly until pump runs smoothly Engage trigger lock Use end of SwitchTip A to press OneSeal B into tip guard D with curve matching tip bore C a LI gt ti3442a Pp eA 0 Nah Bi S E s R em ti3324a 2 Insert SwitchTip in tip bore and firmly thread assem bly onto gun 2 NG To avoid skin injection injury do not stop leaks with ng your hand or a rag ML o SS l 17 Inspect fittings for leaks If leaks occur turn sprayer ioana x OFF immediately Perform Pressure Relief Proce dure Tighten leaky fittings Repeat Startup steps 10 17 If no leaks continue to trigger gun until sys tem is thoroughly flushed Proceed to step 18 ti3327a 18 Place siphon tube in paint pail PAINT ti3316a 12 3A2090C Operation Gun Placement Gun Placement Install Gun 3 Use the 2 Gun Selector Switches to determine which guns are active Each gun selector switch has 3 positions programmed line pattern OFF and 1 Insert gun
22. g nut and remove gun 2 Install gun mount onto gun arm assembly and mount tighten gun mount wing nut a Pat Ng ti18978a ti18979a a SS ti18984a AG oe 3 Install guns into gun mounts ti18985a 4 Slide gun arm assembly out from gun arm mounting slot ti18976a ti18983a 4 Installation 1 Slide gun arm assembly into gun arm mounting slot oe UND e e Nr st Pat B A a Bb o x NOTE Make sure all hoses cables and wires are properly routed through brackets 3A2090C Operation 15 Gun Placement Gun Cable Adjustment 3 Insert plastic cable retainer into cable bracket hole Adjusting the gun cable will increase or decrease the gap between the trigger plate and the gun trigger To 7 aa ens Ds adjust trigger gap perform the steps below IX gt NG Y as gt E D S NG Y ON as 4 Install cable end onto trigger plate pin and install Clip 1 Use wrench to loosen locking nut on cable adjuster 2 Loosen or tighten adjuster until desired result is achieved NOTE More thread exposed means less aga gap between gun trigger and trigger plate 3 Use wrench to tighten locking nut on tie adjuster Adding Gun Cable This line striper is equipped with two gun actuators Each gun actuator is capable of operating two cables For additional 2 to 4 guns gun installation attach cable to the
23. gger Control to start measuring press Gun Trigger Con trol again to stop measuring You can change STALL SIZE wider or narrower or CALC STALLS total number of stalls PARKING CALC MEASURE to start measuring CALC STALLS ti9920b Press SETUP three times to return to PARKING LAYOUT MODE Press Gun Trigger Control button move forward and start to mark dots Press Gun Trigger Control button again to end dots e Parking Layout Mode STALL SIZE DOT SIZE ti9919b 3A2090C Operation Smart Control Operation Angle Stalls 4 Measure and mark the offset distance for the first stall 1 Angle stalls require the operator to input stall angle and depth The Auto Layout System calculates the offset distance based on this input erm DEPTH J dot spacing on ti10059a dot spacing on crm DEPTH A 5 Press SETUP two times to save angled stall dot 1100592 spacing to PARKING LAYOUT MODE 2 From PARKING LAYOUT MODE press SETUP two ANGIE CATE times for ANGLE CALC e Parking Layout Mode STALL SIZE 00 O DOT SIZE e Parking Layout Mode psi STALL SIZE DOT SIZE ti9919b ti9921b 3 ANGLE Press and hold Gun Trigger Control button to change stall angle Angle increases up to 90 and wraps around and starts over at 45 STALL DEPTH Press down arrow to decrease or up arrow to increase stall depth STALL SIZE Press down arrow to decrease or up arrow to
24. ght and left Turn the handle bar right or left to steer the LineStriper ral ran Perform Startup page 10 Use the handle bars of the LineStriper to control all motion during operation In addition to steering the pas LineStriper the handle bars also control forward and co t117518a reverse movement by pulling the forward reverse con pa trol lever NOTE Make sure wheel motor bypass valve is engaged see page 20 To move forward Disengage brake and slowly pull control lever on right side of handlebar i ROSAS 117519 po iang i a P20 02020202070 Lo Parking Emergency Brake This unit is equipped with a parking brake Always engage parking brake when not in operation Brake may also be used to stop machine in an emergency situation JN ti17516a To move in reverse Slowly pull control lever on left side of handlebar 1 Step down on the brake lever to engage parking brake n al ti18550a 5 ti17517a o a 2 Lift brake lever up with foot to disengage parking To stop Release control lever and allow it to return to brake center ti18565a
25. increase stall size 3A2090C Operation 29 Smart Control Operation Marker Mode 3 30 Press the MODE key to select Parking Layout Mode Press SETUP three times to select Marker Layout Mode e PARKING LAYOUT MODE e STALL SIZE 0 GIO DOT SIZE PARKING CALC MEASURE e to start measuring CALC STALLS STALL SIZE ANGLE CALC e to change angle offset Ss 1 ti18507a Use SELECT and EDIT keys to set up reflective marker pattern 48 00 ft 4 01 OOO 8 00 ft p Automatic marker layout example shows typical lane line layout for reflective markers Set space sizes up to 8 consecutive measurements By leaving zeros in any space AutoLayout will skip to the next measurement in a continuous loop OTHER USES e Multiple spaced handicap stall layout e Double line stalls Press gun trigger control and move striper forward to mark dots Press gun trigger control again to stop marking dots t118564a 3A2090C Operation Measure Mode 1 Press SETUP once from Manual Mode display e to start measuring CLEAR ALL gt ti9942a 2 Press Gun Trigger Control and move striper forward or backward back ward is a negative distance ti18564a 3 Press Gun Trigger Control to end measured length Up to six lengths are viewable MEASURE MODE 12
26. into gun holder Tighten clamp ES ne OFF position Programmed disengages Continuous line pattern gun line ti23814a so 4 Use the Gun Trigger Control to actuate guns 2 Examples Position Gun 2 Position gun up down forward reverse left right See Gun Positions Chart page 18 for examples ti18574a Gun 1 HN Gun 2 ti18551a ti18575a Gun IE Gun 2 eN ti6549a ti18572a 3A2090C Operation 13 Gun Placement Gun Arm Mounts 3 Slide gun arm assembly into desired gun arm mounting slot This unit is equipped with front and rear gun arm mounts ti18980a ti18974a Di NOTICE ti18555a Make sure all hoses cables and wires are properly routed through brackets and do NOT rub on tire Contact with tire will result in damaged hoses cables and wires Change Gun Position Front and Back Change Gun Position 1 Loosen gun arm knob and remove from gun arm Left and Right mounting slot S R 5 N i lt NS emova YLA A f 1 Loosen gun arm knob on gun arm mounting slot NIA 2 7 Ni SA PIN ti18972a a A3 lt BAE 2 Slide gun arm assembly including gun and hoses out from gun arm mounting slot N Hee lt ti18975a 2 Remove guns from gun mounts be sure to keep track of which gun is 1 and which gun is 2 ti18973a 14 3A2090C Operation Gun Placement 3 Loosen gun mounting win
27. ng Instructions 0 o o ooo o eee 19 Parking Emergency Brake 19 Drive Engagement 20 Straight Line Adjustment 20 Handle Bar Height Adjustment 20 Platform Storage Position 21 Front Pad Adjustment 21 2 Smart Control Overview 0 0005 22 Quick Guide fsi0cd0e senro sede ob DANNY 22 Smart Control Operation 23 Initial SetU xs rr oa bac dara 23 CalbratOM raise aa 23 Change Units or Language 25 Operation in Manual Mode 26 Operation in Automatic Mode 26 Parking Layout Mode 28 Parking Mode cuca dida Se ka eee MANG 28 Marker MOOG waaa NOR aed nes 30 Measure Mode 202000 e eee 31 Machine Information 31 CIGANUD aia daa ee 32 Hydraulic Oil Filter Change 33 REMOVAL birra da Kan ME RAS 33 Installation 0 0 20 aa 33 Technical Specifications Non PBS 34 Technical Specifications PBS 35 Graco Standard Warranty 36 3A2090C Operation Models Models oss Sees Guns Pressures est Sen Pa oO pose o 2 We Juvasosrs eee JC a 1 pn e 1 ves tan LV 250SPS Lain America Asa Paio every B 1 Yost Tank sse over e 2 ves tran LLV2S0SPS Nonn America Lain Areca Asa Pcie ever B 2 vit woss 2auset B
28. not operate the unit when fatigued or under the influence of drugs or alcohol Do not exceed the maximum working pressure or temperature rating of the lowest rated system component See Technical Data in all equipment manuals Use fluids and solvents that are compatible with equipment wetted parts See Technical Data in all equipment manuals Read fluid and solvent manufacturer s warnings For complete information about your material request MSDS from distributor or retailer Do not leave the work area while equipment is energized or under pressure Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use Check equipment daily Repair or replace worn or damaged parts immediately with genuine manufacturer s replacement parts only Do not alter or modify equipment Alterations or modifications may void agency approvals and create safety hazards Make sure all equipment is rated and approved for the environment in which you are using it Use equipment only for its intended purpose Call your distributor for information Route hoses and cables away from traffic areas sharp edges moving parts and hot surfaces Do not kink or over bend hoses or use hoses to pull equipment Keep children and animals away from work area Comply with all applicable safety regulations Do not carry passengers Check work area for reduced overhead clearance e g doorways tree branches parking ramp ceilings and avoid contacting them
29. o stripe Press button again to stop striping or reduce speed to below 0 3 mph 0 5 kph 3A2090C Operation Advanced Preset Skip Patterns 1 A Preset Skip Pattern can be modified for a custom pattern From AUTO MODE press SETUP key to get preset patterns Automatic Mode CYCLE 40 00 0 mph PAINT 10 00 gt SPACE 30 00 gt ROAD PRE SETS SPACE lt lt 00 30 00 00 SELECT gt 00 ti9936b 2 Use SELECT arrow keys to choose which preset pattern you wish to modify Use EDIT arrow keys to get PAINT and HOSE lengths ROAD PRE SETS gt gt PAINT SPACE lt lt 10 00 30 00 8 00 24 00 5 00 15 00 SELECT gt 3 00 12 00 3 00 9 00 ti9936b 3A2090C Operation Smart Control Operation Use EDIT arrows to change the PAINT line length Use SELECT arrows to scroll down to SPACE length Use EDIT arrows to change the SPACE length Press SETUP key to save and return to AUTOMATIC MODE display ROAD PRE SETS gt gt PAINT 10 0 lt lt SPACE 30 0 SELECT gt NOTE When travel speeds exceed 0 3 mph 0 5 Kph in MANUAL or AUTOMATIC modes the dis play will change to large speed display format Manual Mode Km h Automatic Mode Km h MILS INSTANT AVERAGE MILS INSTANT AVERAGE ti19026a ti19027a 27 Smart Control Operation Parking Layout Mode NOTE For best performance set pressure to 1000 psi 68 9 bar 6 89 MPa and reverse ti
30. p Parking Mode Basic Stalls From MANUAL MODE press MODE button twice for PARKING LAYOUT MODE This display allows you to change stall size and dot size It also shows speed The two dots before and after PARKING MODE flash alter nately when Gun Trigger Control is pressed to signal mode is active o o JOB MIL 1 28 psi Manual Mode e PARKING LAYOUT MODE e 43 DISTANCE GALLONS STALL SIZE job reset gt 4 LINE DOT SIZE Press down arrow opposite DOT SIZE to decrease dot size Press up arrow to increase dot size e Parking Layout Mode psi STALL SIZE sediaan ti9919b Press down arrow opposite STALL SIZE to decrease stall width Press up arrow to increase stall width e Parking Layout Mode psi STALL SIZE DEN Set ti9919b Press Gun Trigger Control button and move striper forward Striper marks dots every 9 0 ft or stall size you have set until Gun Trigger Control button is pressed again ti18564a Advanced Parking Calc 1 Press SETUP and move to PARKING CALC The striper divides the stall size into the measurement taken here to determine the number of stalls that can be striped in this space e Parking Layout Mode STALL SIZE DOT SIZE ti9919b PARKING CALC MEASURE to start measuring CALC STALLS ti9920b The last length measured in the MEASURE MODE is transmitted to this display or press Gun Tri
31. t rags and gasoline Do not plug ot unplug power cords or turn power or light switches on or off when flammable fumes are present Ground all equipment in the work area See Grounding instructions Use only grounded hoses Hold gun firmly to side of grounded pail when triggering into pail Do not use pail liners unless they are anti static or conductive Stop operation immediately if static sparking occurs or you feel a shock Do not use equipment until you identify and correct the problem Keep a working fire extinguisher in the work area INJECTION HAZARD High pressure fluid from gun hose leaks or ruptured components will pierce skin This may look like just a cut but it is a serious injury that can result in amputation Get immediate surgical treatment Do not spray without tip guard and trigger guard installed Engage trigger lock when not spraying Do not point gun at anyone or at any part of the body Do not put your hand over the spray tip Do not stop or deflect leaks with your hand body glove or rag Follow the Pressure Relief Procedure when you stop spraying and before cleaning checking or servicing equipment Tighten all fluid connections before operating the equipment Check hoses and couplings daily Replace worn or damaged parts immediately CARBON MONOXIDE HAZARD Exhaust contains poisonous carbon monoxide which is colorless and odorless Breathing carbon monoxide can cause death e Do not operate in an enclosed area
Download Pdf Manuals
Related Search