Go-Video T2040 User's Manual
Contents
1. You can also use the buttons on top of the unit for basic TV functions including INPUT EXIT CHANNEL a v VOL 4 gt e MENU ENTER POWER CHANNEL VOLUME O O O GDGD AUTO INPUT EXT UP DOWN MENU ENTER These buttons have the same functions as the corresponding buttons on the remote control see page 7 NOTE If you have a PC connected to the LCD TV press the AUTO button to automatically adjust the PC display to fit the LCD screen 2 Getting Started Step 1 Insert Remote Control Batteries Install the supplied batteries as shown below paying attention to the correct polarities Point the remote control directly at the IR sensor located on the front of the TV A Caution Do not expose the remote control to severe shock or vibration Do not expose the remote control to liquids or in an area with high humidity Do not place the remote control in direct sunlight The heat may damage the unit The remote control may not work properly if the IR sensor is exposed to direct sunlight or other strong lighting If this is the case change the angle of the lighting or LCD TV or operate the remote control closer to the IR sensor Ifthe remote control fails to operate replace the batteries in the remote control Improper use of batteries can result in a leakage of chemicals and or explosion e Place batteries with their terminals corresponding to the correct polarities an2. then press 4 to select from the following options e TV Rating Press lt gt to set the maximum allowed TV rating Movie Rating Press 4 to set the maximum allowed Movie rating e New Password Use the number keys to enter a new 4 digit PIN Enter the password again to confirm Enable Press 4 to select Yes enable V Chip or No disable V Chip Closed Caption e Press 4 gt to set Closed Captions to CC1 CC2 TT1 TT2 or Off Clean Memory Erases all stored TV channels Reset e Restores factory settings 3 Advanced Settings cont Video Settings If you have connected an audio video device such as a DVD player or VCR to the AV inputs you can use the Video menu to adjust picture settings V Chip ratings closed captions and more 1 Press INPUT until AV appears in the upper right hand corner If you do not have an AV device connected to the AV Inputs you cannot view the Video settings menu 2 Press MENU ENTER to display the main menu 3 Press 4 to select Video and press MENU ENTER 4 Press to select from the following options VID amp PICTURE E SLEEP TIMER ma V CHIP ES CLOSED CAP t f RESET PRESS Picture Press MENU ENTER to display the Picture Menu then press to select from the following options TY MENU amp PICTURE MODE al TINT VIDEO N R FAVORITE Picture Mode Press 4 to select Standard norm
3. are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio and television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This equipment has been certified to comply with the limits for a Class B computing device pursuant to part 15 of the FCC rules Only peripherals computer input output devices terminals printers etc certified to comply to the Class B limits may be attached to this computer Operation with non certified peripherals is likely to result in interference to radio and TV reception Remarks To meet FCC requirement shielded cables are required to connect the device to a personal computer or other Class B certified dev
4. DPMS standard 4 Help cont Power Saving Mode PC only The LCD TV is equipped with a power management function which automatically reduces power consumption in three power saving modes when not in use Horizontal Green lt 70W REM DBY E lt n Amber lt lt aw Compatible PC Video Mode Case or Fee pana wamm ot vesa oo xen asro on Te vesascoxsoo ion rene ES MRC seqer ran 4 Help cont Limited Warranty Who Provides the Limited Warranty During the warranty period the GoVideo Warranty Administrator will honor service for 90 days labor 1 year parts from the original date of consumer purchase See 9 days ber below for Commercial Industrial or Educational use coverage Remote controls are warrantied for 90 days from the date of purchase year D Whois Protected a rts This warranty protects the original consumer owner of this GoVideo product What is Covered and How Long This warranty covers internal operating parts and service labor to repair or replace covered parts in this GoVideo product for 90 days labor 1 year parts from the date of purchase defined as follows 1 Original Consumer Retail Purchase 2 First Rental Purchase Agreement or 3 First Lease Purchase Agreement the Warranty Period Labor and replacement parts supplied during the Warranty Period are covered only for the remaining portion of the original Warranty Period The Go
5. OUDNESS A Volume e Press 4 gt to set volume level Balance e Press lt gt to set the balance between the TV s left and right speakers Bass e Press 4 to set the bass level Treble e Press 4 to set the treble level Loudness e Press 4 to select Yes boost the overall audio level or No keep the standard audio level Troubleshooting Symptom Solution __________ No picture or sound Ensure power cable is properly inserted in power outlet Ensure power is on Ensure correct input is selected Ensure volume is turned up Ensure sound is muted Ensure headphones are not connected Ensure input source is connected Noisy picture and sound Ensure antenna cable is properly connected Ensure input source is properly connected Picture is not clear Ensure antenna is properly oriented TV signals may be weak for some channels Picture is light or poorly tinted Check Color setting Check Tint setting Picture is too dark Check Brightness setting Fluorescent lamp may have reached end of serviceable life Remote control does not work Check remote control battery Keep IR sensor away from strong fluorescent lighting Picture is not sharp Broadcast reception may be weak Ensure antenna is properly oriented Check Sharpness setting Picture is doubled or tripled Ensure antenna is properly oriented Broadcast signals may be effect
6. RIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT Important Safety Instructions Read instructions All operating instructions must be read and understood before the product is operated Keep this manual in a safe place These safety and operating instructions must be kept in a safe place for future reference Observe warnings All warnings on the product and in the instructions must be observed closely Follow instructions All operating instructions must be followed Attachments Do not use attachments that are not recommended by the manufacturer Use of inadequate attachments can result in accidents Entering of objects and liquids Never insert an object into the product through vents or openings High voltage exists in the product inserting an object can cause electric shock and or short internal parts For the same reason do not spill water or liquid on the product Servicing Do not attempt to service the product 7 by yourself Removing covers can expose you to high voltage and other dangerous conditions Request a qualified service person to perform servicing Repair If any of the following conditions unplug the power cord from the AC outlet and request a qualified service person to perform repairs a When a liquid was spilled on the product or when objects have fallen into the product b When the product has been exposed to rain or water Cleaning Unplug the powe
7. STEM OVERVIOW s s d uac nll scie d k ladn milka kek ence dar n k id e n s dadaa s ae Bad da da ke aya s 13 nea ne DD nr dns ie este et ete destin data essaie est ent ares TV Settings 2 25 yan kab kanada anda dan x n RN aya wu Na la da xe EY ARAN n k v y KK era u K a Eu a GEME ka ina Video Settings OSD Settings Audio Settings 2004 GoVideo All rights reserved Printed in China GoVideo is a registered trademark All other brand and 4 N product names are trademarks or registered trademarks of IMPORTANT their respective companies To aid reporting in case of loss or theft please GoVideo shall not be liable for any errors contained herein record the TV s model and serial numbers in or for any damages arising out of or related to this document or the information contained herein even if GoVideo has the space provided been advised of the possibility of such damages This document is intended for informational and instructional Model No purposes only GoVideo reserves the right to make changes in the specifications and other information contained in this document without prior notification GoVideo disclaims any Serial No obligation to update the information contained herein Ne J FCC amp Safety Information FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits
8. T2040 LCD TV PC Monitor User s Guide www govideo com GO V DEO Table of Contents FCC amp Safety Information ss xi xkllslklli lala kall ainni kala k l ka k seke daka 3 Important Safety Instructions 4 1 Welcome en E RAA VER EKA n Ak ea wa d h e i bA Sal an EL b 5 Unpacking your LCD TVn tarretan a n ked ua y a elek n rey raz n ayni ed ran 5 Rear Panel OVERVIGW assez sisl kak hin me te a Nek azote va en Za dnd an ne Aku k n dada k n R zan E des a j ec 6 Remote Control OVervl W s nx cc pesse bkay dara d kan n banan Xak HERA wan W teers pect 7 TV Control Overview cx cccccec te tein cies wtni dct ayak tense rites sie xana Aue tent ac ee ee anak eet 8 2 Getting Started ss 9 Step 1 Insert Remote Control Batteries siisii iina 9 Step 2 Connect Power Cable Step3 Connect to Antenna Ca Dl i xs i l anm y na a liar lad al S N sa a HEK KERA ENEAN AN 10 Step SARI A ECO 19 TV errre EE seh esavednepdesalitanideest 11 Step 5 Search for Channels sister kla kalan kalana bk Kan n berek k vann tin ane eine 11 Step 6 Select Channel Siz sine bad Gani tn Geet E E E E antennes KEL ER DERE S 11 Step 7 Adjust Volume Step 8 Adjust Screen Angle 12 Step 9 Connect Optional Wall Mount 12 3 Advanced SettingS s x lt alal l dkskk aa k na k k ka lk kka bak kad eka aa kk ada y awed nek 13 Menu SY
9. Video Warranty Administrator shall have no liability for service under this warranty if non OEM Original Equipment Manufacturer replacement parts are used in the repair of your GoVideo product What the Owner Must Do If Service is Required Please contact our customer service department at 1 800 736 7679 to repair or replace your product at GoVideo s option if it proves to be defective in material or workmanship under normal use during the warranty period listed above effective from the date of original consumer purchase of the product Repaired or replacement units are warrantied for the remaining period of the original warranty Please retain dated sales receipt Within the warranty period the customer pays for inbound shipping charges and GoVideo pays return shipping charges Other Warranty Coverage Commercial Industrial or Educational use has the same warranty coverage as stated in this warranty What are the Exceptions This warranty does not cover 1 Normal maintenance service such as cleaning 2 Damage from misuse abuse neglect or accident natural disasters or Acts of God 3 Cabinetry decorative parts A C adapters knobs or buttons 4 The foreign country use of this product 5 GoVideo product which has been electronically or mechanically modified in any way or incorporated into other products 6 Installation and setup service adjustments 7 Owner instruction Your Owner s Guide provides information regarding operat
10. al viewing conditions Vivid brighter viewing conditions or Custom personalized setting e Brightness Press 4 to set the brightness level e Contrast Press 4 to set the contrast level Sharpness Press 4 gt set the picture sharpness e Color Press 4 to set the color saturation e Tint Press lt gt to set the hue Video N R Noise Reduction Press 4 to select Off Low minimum noise reduction Med moderate noise reduction or High maximum noise reduction Sleep Timer e Press 4 to have the TV turn off automatically in 30 60 or 90 minutes e Select Off to cancel the Timer feature V Chip Use the number keys to enter a 4 digit PIN Personal Identification Number then press a v to select from the following options e TV Rating Press 4 to set the maximum allowed TV rating Movie Rating Press 4 to set the maximum allowed Movie rating New Password Use the number keys to enter a new 4 digit PIN Enter the password again to confirm V Chip Press 4 to select Yes enable V Chip or No disable V Chip Closed Caption e Press 4 gt to set Closed Captions to OFF Cap1 Cap2 Text1 or Text2 Reset e Restores factory settings 3 Advanced Settings cont OSD Settings The OSD On Screen Display menu allows you to set the language position size and style of the on screen menu system 1 Press INPUT to select any active in
11. an enclosed place such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions are followed The LCD panel used in this product is made of glass Therefore it can break when the product is dropped or applied with impact Be careful not to be injured by broken glass pieces in case the LCD panel breaks Heat sources Keep the product away from heat sources such as radiators heaters stoves and other heat generating products including amplifiers The LCD panel is a very high technology product with many thin film transistors giving you fine picture details Occasionally a few non active pixels may appear on the screen as a fixed point of blue green or red Please note that this does not affect the performance of your product If an outside antenna is connected to the television equipment be sure the antenna system is grounded so as to provide enough protection against voltage surges and built up static charges Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode For added protection to this television equipment during a lightning storm or when it is left unattended and unused for long periods of time
12. d Different types of batteries have different characteristics Do not mix batteries of different types Remove batteries when they become weak The batteries supplied with the product may have a shorter life expectancy due to storage conditions Ifthe remote control is not used for an extended period of time remove the batteries from the remote control Objects between the remote control and IR sensor may prevent proper operation 2 Getting Started cont Step 2 Connect Power Cable 1 Connect the supplied power cable to the AC In jack on the back of the LCD TV 2 Plug the power cable into a standard AC outlet NL Caution Always turn the the LCD TV off when connecting the power cable e Always unplug the power cable from the LCD TV and power outlet when not using the TV for a long period of time The LCD TV has a universal power supply that allows operation with either 100 120V AC or 220 240VAC voltage No user adjustment is required Step 3 Connect to Antenna Cable Connect the TV to your antenna or cable satellite hookup or PC as shown E Sao I Connect to PC Connect to Antenna Connect to Cable Box or or Basic Cable Satellite Receiver OUTPUT our AUDIO VIDEO sveo 00 D Ww RF N o RF Cable 2 Getting Started cont Step 4 Turn on TV Press POWER on the remote control The Power indicator will turn green e Pre
13. ed by mountains buildings etc Picture is speckled May be interference from cars trains high voltage lines neon lights etc May be interference between antenna and power cable Try positioning them further apart Stripes on screen or colors fade May be interference from other devices Radio and cell phone transmission antennas may also cause interference Use the LCD TV as far away as possible from devices that may cause possible interference 4 Help cont Technical Specifications Front Panel Controls Remote control Audio System OSD Controls PC Mode selector PC TV Video S Video YCbCr Channel Search Input Return Ch Vol Menu Enter Power IR remote Stereo 3W 3W speakers Contrast Brightness H Position V Position Phase Pixel Adj Recall Defaults Auto Adjust Information Clock 6 Languages OSD Position OSD Timeout Volume Mute OSD Controls TV Video Dimension W x H x D Weight Operating Temperature Channel Edit Auto Scan Stereo 5 Languages Sharpness NR Reset Contrast Brightness Tint Color Timer Off OSD Transparent V Chip Closed Captions Loudness Balance Treble Bass 21 3 x 18 2 x 8 2 540 x 462 x 209 mm approximate 18 1 Ibs 8 2 kg approximate 41 F to 104 F 5 C to 40 C Humidity Altitude 10 to 80 non condensation Up to 12 000 ft Safety EMI Regulation Power Saving UL CSA FCC VESA
14. ice Information to Users The unit is for office equipment used Any change or modifications expressly approved by the party responsible for compliance could void the user s authority to operate this equipment DOC NOTICE This product conforms to Canadian Class B emissions regulations Ce produit est conforme aux r glements d mission Canadienne class B CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute risk of fire or electric shock This symbol is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying this product WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE NOTE DU DOC This product conforms to Canadian Class B emissions regulations Ce produit est conforme aux r glements canadiens relatifs aux missions pour les appareils de class B WARNING FCC regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user s authority to operate this equipment CAUTION TO PREVENT ELECT
15. ing instructions and user controls For additional information contact your authorized GoVideo dealer Go Video is not responsible for any shipping handling or insurance charges This Exclusive Limited Warranty excludes all incidental and consequential damages Some states do not allow the exclusion of incidental and consequential damages so the above exclusion may not apply to you ALL IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY PERIOD Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This Exclusive Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state GOVIDEO WARRANTY ADMINISTRATOR 7835 East McClain Drive Scottsdale Arizona 85260 1732 customersupport govideo com 1 800 736 7679 GO VIDEO
16. lable channels e Channel Edit Press 4 gt to Add or Erase the selected channel from your channel list Fine Tuning Press 4 gt to fine tune the selected station in 0 05MHz increments e Favorite Press 4 gt to select Normal or User and press MENU ENTER If you select User press to select one of the 20 placeholders for your favorite channels then enter the channel number directly using the 0 9 keys for each placeholder All channel numbers that are set to 0 will be disabled Picture Press MENU ENTER to display the Picture Menu then press to select from the following options VAIN PICTURE MENU PICTURE MOD e Picture Mode Press 4 to select Standard normal viewing conditions Vivid brighter viewing conditions or Custom personalized setting Brightness Press lt gt to set the brightness level e Contrast Press 4 gt to set the contrast level e Sharpness Press 4 gt set the picture sharpness e Color Press 4 to set the color saturation e Tint Press 4 to set the hue Video N R Noise Reduction Press 4 to select Off Low minimum noise reduction Med moderate noise reduction or High maximum noise reduction Sleep Timer e Press 4 to have the TV turn off automatically in 30 60 or 90 minutes Select Off to cancel the Timer feature V Chip Use the number keys to enter a 4 digit PIN Personal Identification Number
17. m the following options RCAMENU H SIZE a FINE H POSITION V POSITION AUTO ADJUST FER F e H Size Press 4 to set the width of the PC display e Fine Press 4 b to set the sharpness of the PC display e H Position Press 4 to set the horizontal position left right of the PC display e V Position Press lt gt to set the vertical position up down of the PC display Auto Adjust Press MENU ENTER to automatically adjust the PC display to fit the screen Information Displays the resolution e g 640 x 480 and refresh rate e g 60 Hz of the PC display Reset e Restores factory settings 3 Advanced Settings cont TV Settings The TV settings menu allows you to adjust channels picture settings timers V Chip ratings closed captions and more 1 Press INPUT until the current channel number appears in the upper right hand corner TV mode 2 Press MENU ENTER to display the main menu 3 Press lt gt to select TV and press MENU ENTER 4 Press to select from the following options tt RESET PRESS KEY Set Up Press MENU ENTER to display the Setup Menu then press to select from the following options TV MENU SETUP MENU amp ANT SOURCE AUTO SEARCH gt CHANNEL EDIT Ez FINE TUNING FAVORITE 4 gt ANTENNA e Antenna Source Press 4 to select Antenna or Cable e Auto Search Press gt to begin searching for all avai
18. onnects to the VGA Out of a PC using a VGA cable 9 Audio In Connects to the Audio Out of a PC using a 1 8 stereo mini plug 10 Line Out Connects to Headphones or to the Line In of a stereo receiver using a 1 8 stereo mini plug 1 Welcome cont Remote Control Overview 1 POWER Turns TV on and off 2 0 9 10 Selects channels directly 3 DISPLAY Displays TV status 4 CH Selects next or previous channel 5 VOL Adjusts volume 6 RETURN Returns to previous menu or exits menu system 7 ASPECT Sets TV aspect ratio to 4 3 standard or 16 9 widescreen 8 CHANNEL SEARCH Searches for all available channels in the selected tuner band 9 CAPTIONS Selects the desired Closed Caption mode 10 INPUT Changes on screen view to PC TV AV Video In SV S Video In or YCbCr Component Video In 11 JUMP Displays the previously viewed channel 12 FAVORITES Selects your favorite channels as set in the TV Settings menu see page 14 13 MENU ENTER Displays the on screen menu system Confirms settings in the menu ystem PICTURE ASPECT AUDIO CAPTIONS N OD GO VIDEO 14 MUTE Turns sound on and off 15 PICTURE MODE Sets picture brightness to standard normal viewing conditions demo brighter viewing conditions or favorite custom viewing as set in Picture menu 16 AUDIO Selects Stereo Mono or SAP 1 Welcome cont TV Control Overview
19. put The menu system will only display if there is a signal detected for the selected input 2 Press MENU ENTER to display the main menu 3 Press lt gt to select OSD and press MENU ENTER 4 Press to select from the following options LANGU H POSITION V POSITION E TIMEOUT II OSD SIZE OSD STYLE ENG FRA ITA DEU ESP Language e Press lt gt to set the menu language to English French Italian German or Spanish H Position e Press 4 gt to move the menu left and right V Position e Press 4 to move the menu up and down OSD Timeout e Press 4 to set how long the menu will be displayed before it times out disappears from the screen OSD Size Press lt gt to select Large magnify the size of the menu or Small keep the standard size OSD Style e Press 4 to select Normal display the menu normally or Dim dim the menu so you can see the TV behind it 3 Advanced Settings cont Audio Settings The Audio menu allows you to set the LCD TV volume level balance bass treble and loudness 1 Press INPUT to select any active input The menu system will only display if there is a signal detected for the selected input 2 Press MENU ENTER to display the main menu 3 Press 4 to select Audio and press MENU ENTER 4 Press a v to select from the following options AUDIO MENU J VOLUME 4 BALANCE lt BASS J TREBLE 4 L
20. r cord from the Ac outlet before cleaning the product Use a damp cloth to clean the product Do not use liquid cleaners or aerosol cleaners Water and moisture Do not use the product near water such as bathtub washbasin kitchen sink and laundry tub swimming pool and in a wet basement Stand Do not place the product on an unstable cart stand tripod or table Placing the product on an unstable base can cause the product e to fall resulting in serious personal injuries as well as damage to the product Use only a cart stand tripod bracket or table recommended by the manufacturer or sold with the product When mounting the product on a wall be sure to follow the manufacturer s instructions Use only the mounting hardware recommended by the manufacturer PORTABLE CART WARNING Symbol provided by RETAC When relocating the product placed on a cart it must be moved with utmost care Sudden stops excessive force and uneven floor surface can cause the product to fall from the cart Ventilation The vents and other openings in the cabinet are designed for ventilation Do not cover or block these vents and openings since insufficient ventilation can cause overheating and or shorten the life of the product Do not place the product on a bed sofa rug or other similar surface since they can block ventilation openings This product is not designed for built in installation do not place the product in
21. ss POWER again to turn off the TV Step 5 Search for Channels Press SEARCH on the remote control e The LCD TV will automatically search for all available channels To change the tuning band see TV setup To add or delete channels see TV setup Step 6 Select Channels To select a channel use the CH buttons or enter a 1 2 or 3 digit number as follows To select a 1 or 2 digit channel number e g channel 5 1 Press the 0 button 2 Press the 5 button or simply press the 5 button To select a 3 digit channel number e g channel 115 Complete the following procedure within 4 seconds 1 Press the 10 button 2 Press the 1 button 3 Press the 5 button To select another input Press INPUT to change the on screen view to PC TV AV Video In SV S Video In or YCbCr Component Video In Notes e With the Antenna Source set to Antenna you can select channels 1 69 e With the Antenna Source set to Cable you can select channels 1 125 channels To set or change the Antenna Source see page 14 Step 7 Adjust Volume Press the VOL buttons to adjust the volume To mute the sound press MUTE 2 Getting Started cont Step 8 Adjust Screen Angle To set the LCD TV to a comfortable viewing angle tilt the screen up to 5 degrees forward or 20 degrees backward Step 9 Connect Optional Wall Mount 1 Remove the supplied stand as shown 2 Attach the LCD TV to a s
22. tandard VESAArm wall mount 100 x 100 mm 3 Advanced Settings Menu System Overview Press the MENU ENTER button to view the five main menu categories PC Video OSD Audio TV OSD Audio Depending on the input you are viewing one or more of these options will be dimmed PC Settings If you are using the LCD TV as a PC monitor you can use the PC menu to adjust the brightness contrast color size and position of the PC display 1 Press INPUT until PC appears in the upper right hand corner If you do not have a PC connected to the VGA Input you cannot view the PC settings menu 2 Press MENU ENTER to display the main menu 3 Press 4 to select PC and press MENU ENTER 4 Press a v to select from the following options jU BRIGHTNESS CONTRAST COLOR IMAGE INFORMATION RESET Brightness Press 4 to set the brightness level Contrast e Press 4 to set the contrast level Color Press MENU ENTER to display the Color Menu then press to select from the following options PC MENU COLOR _ MENU 6500K 6500K 7500K 9300K Press to select the desired color temperature User For a custom color temperature press to select the individual RGB Red Green and Blue sliders Then use 4 to fine tune each color Image Press MENU ENTER to display the Image Menu then press to select fro
23. unplug it from the wall outlet and disconnect the antenna This will prevent damage to the equipment due to lightning and power line surges An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Unpacking your LCD TV 1 LCD TV 2 Remote Control 3 AAA Batteries 2 O Oo 0 re 5 VGA Cable 6 TV Tuner 7 AV Cable 8 RF Cable 9 User s Guide amp Registration Card 1 Welcome cont Rear Panel Overview Push arrow mark to open cover AC In Connects to the supplied power cable Video In Connects to the Video Out of a DVD player VCR or other AV equipment S Video In Connects to the S Video Out of a DVD player VCR or other AV equipment Audio In Connects to the Audio Out of your AV equipment when using the Video or S Video connections Component Video Y Cb Cr In Connects to the Component Video Out of a DVD player or other AV equipment VT 77 6 Audio In Connects to the Audio Out of your AV equipment when using the Component Video connections 7 RF In Connects to an Antenna Cable TV jack Cable Box or Satellite Receiver using an RF cable 8 VGAIn C
Download Pdf Manuals
Related Search