Global Machinery Company HD1400K User's Manual
Contents
1. spindle lock button 9 pressed with the other hand WARNING Do not attempt to tighten the chuck by gnpping the front part and turning the dnll on Damage to the tool and personal injury may result Be sure to tighten the chuck with the spindle lock button held pressed to achieve maximum tightness anti clockwise to loosen the collar and slip it over the chuck onto the drill 2 Insert the depth gauge 3 in the hole at the top of the handle 2 3 The auxiliary handle 2 can swivel 360 for the most comfortable position and easiest operation 4 The depth gauge 3 helps keep an accurate depth when drilling holes to a set depth 5 To change the position of the depth gauge 3 turn the handle 2 gnp anti clockwise until the depth gauge is loose enough to slide through the hole 6 Set the depth checking the depth with a steel rule for most accurate measurement and then tum the handle gnp clockwise to tighten both the depth stop and the auxiliary handle in the required position Operation Starting and stopping Operational controls 1 Ensure that the tool is in good condition 2 Plug the cordset into the mains socket 3 Depress the tngger switch 7 to start the drill and release the trigger when you wish to stop 4 Press the lock on button 5 whilst the trigger is depressed if you require continuous operation To disengage the lock on switch press the tngger then release it Va2. the bit from slipping off the starting point Increase the speed as the drill bit bites into the material e When drilling through holes place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole e Do not lock the tngger in the on position when the drill may need to be stopped suddenly Metal drilling e For maximum performance use high speed steel bits for metal or steel drilling e Move dnlling hammer mode selector to drilling mode S e Use a centre punch to mark the hole location on the workpiece e Begin drilling at a very low speed to prevent the bit from slipping off the starting point e Maintain a speed and pressure which allows cutting without overheating the bit Applying too much pressure will Overheat the drill Wear the bearings Bend or burn bits Produce off centre or irregular shaped holes e When drilling large holes in metal it is recommended to drill with a small bit at first then finish with a larger bit Also lubricate the bit with oil to improve drilling action and increase bit life Masonry drilling e For maximum performance use tungsten carbide tipped masonry impact bits when drilling holes in brick tile concrete etc e Move dnilling hammer mode selector to hammer mode T e Apply light pressure and medium speed for best results in brick e Apply additional pressure and high speed for hard matenals such as concrete e When dnlling in
3. tile practice on a scrap piece to determine the best speed and pressure Cleaning 1 Keep your machine and its cord clean The outside of the machine can be cleaned using a damp soft cloth with a mild detergent if required 2 Some maintenance products and solvents may damage the plastic parts these include products containing benzene trichloroethylene chlonde and ammonia 3 Excessive sparking generally indicates the presence of dirt in the motor or abnormal wear on the carbon brushes 4 Take special care to keep the ventilation inlets outlets free from obstruction cleaning with a soft brush followed by a compressed air jet will usually be sufficient to ensure acceptable internal cleanliness 5 Wear eye protection when carrying out cleaning CAUTION Do not use cleaning agents to clean the plastic parts of the dnl Power cord maintenance If the supply cord needs replacing the task must be carried out by the manufacturer the manufacturer s agent or an authorised service centre in order to avoid a safety hazard Carefully read the entire Instruction Manual before using this product Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 Australia or 0800 445 721 New Zealand When you make your call please have the following information at hand e GMC Product Type GMC Product Code A GMC Service Engineer will take your call and in most cases will be able to solv
4. 9 u GLOBAL MACHINERY COMPAN INSTRUCTION MANUAL L200 VW wmm Hammer Drill 30 REPLACEMENT SATISFACTION WARRANTY GUARANTEE Melbourne Perth Auckland Hong Kong Shanghai H D 1 4 o o K e Taipei New York Verona London Paris 040413 HD1400K EDS Contents Warranty Introduction Environmental protection Description of symbols Specifications Safety instructions Additional safety rules for drills Know your product Unpacking Auxiliary handle and depth gauge Inserting and removing bits Operation Variable speed trigger switch Speed adjustment Reversing the direction of rotation Drilling hammer mode selector Chuck replacement Hints for use Drilling Wood Metal Masonry Cleaning Power cord maintenance REPL ACEW ANTY Wo W r 6 GO WO Do CO CIN GD KR ba amp bai bai D bal Ral Ra Ra k mim b i CO O Full 2 Years Home Use Warranty Whilst every effort is made to ensure your complete satisfaction with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domestic use from the date of the onginal purchase If found to be defective in matenals or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item
5. A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the nght to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use It also does not cover any bonus accessones unless the tool is a GMC Platinum Professional model Please ensure that you store your receipt in a safe place Conditions apply to the above warranty If you need direction of what constitutes a free of charge warranty claim please review the guide given on the rear of the Receipt Holder An indication is given as to the types of claim that are permissible and those that are not Dear Customer If you require any help with your product whether it is a Warranty claim spare part or user information please phone our Help Line for an immediate response Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand Introduction Your new GMC power tool will more than satisfy your expectations It has been manufactured under stringent GMC Quality Standards to meet supenor performance criteria You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service Caution Carefully read through this ent
6. e drill use safety equipment including safety glasses or shield ear defenders and protective clothing including safety gloves Wear a dust mask if the drilling operation creates dust If in doubt do not plug in the tool Using a power source with a voltage less than the nameplate rating is harmful to the motor The tool must be used only for its prescnbed purpose Any use other than those mentioned in this Manual will be considered a case of misuse The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse To use this tool properly you must observe the safety regulations the assembly instructions and the operating instructions to be found in this Manual All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards Children and frail people must not use this tool Children should be supervised at all times if they are in the area in which the tool is being used It is also imperative that you observe the accident prevention regulations in force in your area The same applies for general rules of occupational health and safety The manufacturer shall not be lable for any changes made to the tool nor for any damage resulting from such changes Even when the tool is used as prescribed it is not possible to eliminate all residual nsk factors The following hazards may arise in connection with the tools const
7. e of action only when the drill has come to a complete standstill NOTE Hammer action drilling should only be preformed in the forward direction Chuck replacement Chuck removal Always wear eye protection Tighten the chuck around the shorter end of a hex key not supplied of 5mm or greater size Using a wooden mallet or similar object strike the longer end in the clockwise direction This will loosen the screw inside the chuck 1 Open chuck jaws fully 2 Insert a phillips head screwdnver into front of chuck between jaws to engage screw head Remove screw by tuming clockwise 3 Place the hex key in chuck and tighten Using a wooden mallet or similar object strike key sharply in the anti clockwise direction This will loosen the chuck so that it can be unscrewed by hand Chuck installation 1 Screw the chuck on by hand as far as it will go and insert screw LH thread 2 Tighten the chuck around the shorter end of a 1 4 or large hex key not supplied stnke the longer end in the clockwise direction with a wooden mallet 3 Remove the hex key and open the jaws fully Tighten the screw in the centre of the chuck firmly Hints for use Note When drilling into masonry the drilling rate is fast and burnout of the tip will occur if the drill bit is not constantly cleared e Use only correctly sharpened drill bits which are suitable for the material being drilled e To drill hard materials firm p
8. e your problem over the phone You are welcome to use this phone in service to make suggestions or give comments about any GMC product GMC GLOBAL MACHINERY COMPANY 45 55 South Centre Road Melbourne Airport Victona Australia 3045 Tel 03 8346 1100 Fax 03 8346 1200 With continuing product development changes may have occurred which render the product received slightly different to that shown in this instruction manual The manufacturer reserves the nght to change specifications without notice Note Specifications may differ from country to country 7 DAYS A WEEK 7AM 7 PM ven The GMC 777 Helpline operates from 7am to 7pm 7 days a week EST This allows you to contact GMC directly with any queries and technical questions you have regarding our products Save this Manual for future reference
9. ed by a qualified repair personnel using only identical replacement parts This will ensure that the safety of the power tool is maintained Additional safety rules for drills e Wear ear protectors with impact drills Exposure to noise can cause hearing loss e Use auxiliary handles supplied with the tool Loss of control can cause personal injury e If possible always use clamps or a vice to hold your work e Always switch off before you put the drill down e Ensure that the lighting is adequate e Do not put pressure on the drill such that it slows the motor down Allow the drill bit to cut without pressure You will get better results and you will be taking better care of your tool e Keep the area free of tnpping hazards e Do not let anyone under 18 years operate this tool e Only use accessory bits in good condition e Before drilling check that there is sufficient clearance for the drill bit under the workpiece e Do not touch the bit after operation It will be very hot e Keep your hands away from under the workpiece e Never use your hands to remove sawdust chips or waste close by the bit e Rags cloths cord string and the like should never be left around the work area e Support the work properly e If you are interrupted when operating the drill complete the process and switch off before looking up e Periodically check that all nuts bolts and other fixings are properly tightened e When using th
10. ire Instruction Manual before using your new GMC Power Tool Take special care to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate Environmental protection a Recycle unwanted matenals instead of disposing of them as waste All tools hoses G and packaging should be sorted taken to the local recycling centre and disposed of in an environmentally safe way Description of symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use Wear hearing protection Wear eye protection Wear breathing protection OO Double insulated for additional protection Conforms to relevant standards for electromagnetic compatibility N380 Specifications Voltage 230 240V 50Hz Input power 1400W No load speed 0 2800 min Number of impacts 0 33000 min Chuck size 13mm Maximum drilling capacity Wood 32mm Steel 13mm Masonry 16mm Net weight 3 4kg Safety instructions WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the wamings below refers to your mains operated corded power tool o
11. ommon sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use safety equipment Always wear eye protection Safety equipment such as a dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the tool on A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations e Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure that these are connected and properly used Use of these devices can reduce dust related hazards Power tool use and care e Do not force the power tool Use the correct power tool for your application The correct po
12. r battery operated cordless power tool Save these instructions Work area e Keep work area clean and well lit Cluttered and dark areas invite accidents e Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes e Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety e Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock e Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refngerators There is an increased nsk of electric shock if your body is earthed or grounded e Do not expose power tools to rain or wet conditions Water entering a power tool will increase the nsk of electric shock e Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the nsk of electnc shock Personal safety e Stay alert watch what you are doing and use c
13. ressure is required on the power tool However excessive pressure does not improve performance and places unnecessary pressure on the tool and its bit When screw dnving always use a pilot hole and set the speed dial to low Press firmly on the screw head and pull the tngger gradually increasing the speed It is always wiser to test the screw dnving on a scrap piece of the same material you are using Larger diameter holes in hard wood steel and concrete have to be drilled at slower speeds However the motor must not be struggling with the operation If the motor is struggling DO NOT continue working pull the drill clear of the workpiece and run it on fast speed for a minute or so allowing the motor time to cool down before you continue with the task If the job is too hard for the drill do not continue otherwise you could permanently damage the motor e Concrete drilling should De cared out on the highest speed DO NOT overload motor when drilling concrete DO NOT use too much pressure as the hammer action relies on the drill bit being able to move back and forward in the hole being drilled Always clear the flutes of the drill bit by removing it from the hole regularly Wood Drilling e For maximum performance use high speed steel bits for wood drilling e Move dniling hammer mode selector to drilling mode S e Secure the workpiece to prevent it from turning when drilling e Begin drilling at a very low speed to prevent
14. riable speed trigger switch 1 You can adjust the speed of the drill between zero and maximum by varying the pressure on the tngger The harder you press on the tngger the faster the dnll will operate Speed adjustment 1 You can change the maximum speed setting by turning the speed dial 8 located on the tngger switch 7 To increase the speed tum the dial so that the thickest part of the line is above the arrow on the trigger as shown in Fig 1 Ty The forward reverse switch 6 Reversing the direction of rotation protrudes from one side of the dnll to the other 2 The arrow head symbol on each side of the switch indicates the direction of drilling when the switch is pushed from that side The forward direction is selected when the arrow head symbol points to the front of the dnl The reverse direction is selected when the arrow head symbol points to the rear of the drill CAUTION Any attempt to reverse the direction of rotation whilst the drill is turning is likely to permanently damage the motor gearing or both Drilling hammer mode selector You can use the drill for both hammer action and normal drilling 1 Use the drilling hammer mode selector 4 to select hammer or drill action The type of drilling selected is indicated by the symbol on each side of the drill 2 Push the selector to T for hammer action 3 Push the selector to for drill action CAUTION Change the mod
15. ruction and design e Damage to the lungs if an effective dust mask is not worm e Damage to hearing if effective ear defenders are not worn Know your product 1 13mm Single sleeve keyless metal chuck 2 Over moulded auxiliary handle 3 Depth gauge 4 Dnlling hammer mode selector 5 Lock on button 6 Forward Reverse switch 7 Variable speed trigger switch 8 Speed dial 9 Spindle lock button 10 Metal gear box cover Unpacking Installing and removing bits Due to modern mass production techniques it is unlikely CAUTION Always ensure that the drill is switched off and that your GMC Power Tool is faulty or that a part is plug is removed from the power point before making any missing If you find anything wrong do not operate the adjustments tool until the parts have been replaced or the fault has 1 The drill features a keyless chuck 1 and spindle lock been rectified Failure to do so could result in senous button 9 for greater convenience of use e SE gury 2 To insert a drill bit or other Auxiliary handle and depth gauge accessory press the spindle 1 Tum the auxiliary handle 2 lock button 9 with one hand and use your other hand to rotate the chuck 1 anti clockwise Rotate it sufficiently for the chuck to open far enough to accept the bit or accessory 3 Fully insert the bit or accessory into the chuck 1 and tighten securely by rotating the chuck clockwise with one hand whilst holding the
16. wer tool will do the job better and safer at the rate for which it was designed e Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the nsk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessones and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation Service e Have your power tool servic
Download Pdf Manuals
Related Search