Global Machinery Company DEC001SI User's Manual
Contents
1. 4 Select a suitable Collet for the accessory to be used and insert it in the collet nut shaft 5 Turn the Collet nut in an anti clockwise direction to loosen and when the bit is in place turn the Collet nut in clockwise direction to lock it in place whilst depressing the spindle lock 6 Make sure that the bit is inserted as far as possible Having too much shaft exposed could cause it to damage or bend Locating a cutting sanding disc 1 Insert the disc holder into the Collet 7 whilst the Collet nut 6 is loosened 2 Remove the screw from the end of the disk holder with the 2 in 1 wrench provided and insert the screw through the cutting sanding disc 3 Replace the screw and tighten attaching the cutting or sanding disc onto the holder Do not over tighten Locating a sanding drum 1 Loosen the small screw in the top of the holder This allows the rubber to slacken 2 Slide the sanding drum onto the holder 3 Secure the sanding drum in place by tightening the screw causing the rubber drum to bulge and grip the drum Do not over tighten Attaching the flexible shaft WARNING Never bend the flexible shaft with a radius of less than 150 mm 6 when operating Please store the flexible shaft in the designated compartment of the carry case when not in use 1 Remove the collet cover 9 and loosen the collet nut 6 by turning them anti clockwise 2 Insert the inner cable of the flexible shaft i2. It is also imperative that you observe the accident prevention regulations in force in your area The same applies for general rules of occupational health and safety The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors The following hazards may arise in connection with the tool s construction and design e Damage to the lungs if an effective dust mask is not worn e Damage to hearing if effective earmuffs are not worn e Damage to eyes if effective goggles are not worn Risk of injury unless hands are kept well clear of cutting devices Unpacking Due to modern mass production techniques it is unlikely that your GMC Power Tool is faulty or that a part is missing If you find anything wrong do not operate the tool until the parts have been replaced or the fault has been rectified Failure to do so could result in serious personal injury Operation WARNING Before connecting a tool to a power source power point receptacle outlet etc be sure that the voltage supply is the same as that specified on the nameplate of the tool A power source with a voltage greater than that specified for the tool can result in serious injury to the user as well as damage to the tool If in doubt do not plug in the tool Using a power source with a voltage less than the nameplat
3. Power cord Environmental protection Recycle unwanted materials instead of a disposing of them as waste All tools hoses Va and packaging should be sorted taken to the local recycling centre and disposed of in an environmentally safe way Description of symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use Wear hearing protection Wear eye protection Wear breathing protection Double insulated for additional protection Conforms to relevant standards for naso electromagnetic compatibility ZN GRUON T Thoroughly read and understand all LI instructions before using this product S2 10 min Indicates operating time at no more than 10 minutes at rated load followed by a complete cool down of the tool Specifications Input power 13W Power supply 230 240V 50 Hz Engraving bit Tungsten Carbide Tipped steel Cord length 1 4 metres Tool Weight 0 4 kg Safety instructions WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings below refers to your mains operated corded power tool or battery operated cordless power tool Save these instructions Work area e Keep work area clean and well lit Cluttered and dark areas invite accidents Do not operate power tools in explosive atmos
4. alcohol or medication A moment of inattention while operating power tools may result in serious personal injury e Use safety equipment Always wear eye protection Safety equipment such as a dust mask non skid safety shoes hard hat or hearing protection use e Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents e Remove any adjusting key or wrench before turning the tool on A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts e If devices are provided for the connection of dust extraction and collection facilities ensure that these are connected and properly used Use of these devices can reduce dust related hazards Code DECOO7EN Date 060113 op DCR Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if t
5. apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use It also does not cover any bonus accessories unless the tool is a GMC Platinum Professional model Please ensure that you store your receipt in a safe place Conditions apply to the above warranty If you need direction of what constitutes a free of charge warranty claim please review the guide given on the rear of the Receipt Holder An indication is given as to the types of claim that are permissible and those that are not Dear customer If you require any help with your product whether it is a Warranty claim spare part or user information please phone our Help Line for an immediate response Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand Introduction Your new GMC power tool will more than satisfy your expectations It has been manufactured under stringent GMC Quality Standards to meet superior performance criteria You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service Caution Carefully read through this entire Instruction Manu
6. lit and well ventilated e Never leave the soldering iron plugged in and unattended e Be sure to always solder on a fire resistant surface e Never touch the soldering tip while the soldering iron is plugged in Solder contains lead which is a poisonous metal so always ensure your hands are washed after using solder To use this tool properly you must observe the safety regulations the assembly instructions and the operating instructions to be found in this Manual All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards Children and infirmed people must not use this tool Children should be supervised at all times if they are in the area in which the tool is being used It is also imperative that you observe the accident prevention regulations in force in your area The same applies for general rules of occupational health and safety The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors The following hazards may arise in connection with the tool s construction and design e Damage to the lungs if an effective dust mask is not worn e Damage to hearing if effective earmuffs are not worn Damage to eyes if effective goggles are not worn e Risk of injury unless hands are kept well clea
7. maintenance If the supply cord needs replacing the task must be carried out by the manufacturer the manufacturer s agent or an authorised service centre in order to avoid a safety hazard Please refer to your warranty card which is separate to these instructions Givi C Full 2 Year Warranty This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use Consistent with our product development programme improvements may have been made which render the contents of the tool s packaging or user instructions slightly different to the product received Phone 03 8346 1100 Facsimile 03 8346 1200 Email info gmca com au Website www gmcompany com Copyright Global Machinery Company Australia Proprietary Limited 2001 Dear customer if you require any help with your product whether it is a Warranty Cl
8. or resulting from abuse accidents alterations or commercial or business use Consistent with our product development programme improvements may have been made which render the contents of the tool s packaging or user instructions slightly different to the product received Phone 03 8346 1100 Facsimile 03 8346 1200 Email info gmca com au Website www gmcompany com Copyright Global Machinery Company Australia Proprietary Limited 2001 Dear customer if you require any help with your product whether it is a Warranty Claim spare part or user information please phone our Help Line 1300 880 001 Australia or 0800 445 721 New Zealand for an immediate response Product of China manufactured to exacting GMC quality standards ABN 68 093 174 808 The GMC 777 Helpline operates from 7am to 7pm 7 days a week EST This allows you to contact GMC directly with any queries and technical questions you have regarding our products Save this Manual for future reference PE YEAR REPLACEMENT WARRANTY GLOBAL MACHINERY COMPANY 45 55 South Centre Road Melbourne Airport Victoria Australia 3045 Tel 03 8346 1100 Fax 03 8346 1200 GLOBAL MACHINERY COMPANY 3 0 CORDLESS SLREWDRIVER DECOOZ50 1 Chuck 2 Forward Reverse switch 3 Handle adjusting switch 4 Charging socket 5 Charging indicator Full 2 years home use warranty Whilst every effort is made to ensure your complete satisfacti
9. our Help Line for an immediate response Phone 1300 880 0071 in Australia or 0800 445 721 in New Zealand Introduction Your new GMC power tool will more than satisfy your expectations It has been manufactured under stringent GMC Quality Standards to meet superior performance criteria You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service Caution Carefully read through this entire Instruction Manual before using your new GMC Power Tool Take special care to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate Environmental protection Recycle unwanted materials instead of disposing Qa of them as waste All tools hoses and packaging should be sorted taken to the local recycling 3 centre and disposed of in an environmentally safe way Description of symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use Wear hearing protection Wear eye protection Wear breathing protection 0 Double insulated for additional protection Conforms to relevant standards for electromagnetic compatibility N380 Specifications Screwdriver Battery voltage 3 6V DC Battery
10. rating 600mAh Ni Cd No load speed 200min Tool weight 0 4 kg Battery Charger Input voltage 230 240V 50 Hz Output voltage 5V DC 300mA Charging time 5 7 Hours Safety instructions WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings below refers to your mains operated corded power tool or battery operated cordless power tool Save these instructions Work area e Keep work area clean and well lit Cluttered and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes e Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety e Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock e Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock e
11. tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts e If devices are provided for the connection of dust extraction and collection facilities ensure that these are connected and properly used Use of these devices can reduce dust related hazards Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed e Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired e Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and
12. Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Code DEC002SD O e Use safety equipment Always wear eye protection Safety equipment such as a dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries e Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents e Remove any adjusting key or wrench before turning the tool on A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations e Dress p
13. E To turn the tool on press the small On Off Switch 1 upwards to the I position To turn the tool off push the on off Switch 1 down to the O position 3 Hold the engraver at an angle like you would hold a pen Do not press down hard while engraving use light pressure while guiding the point over the work to be completed Adjusting the depth of engraving 1 The stroke adjustment dial 3 located on the side of the engraver controls the stroke length and therefore the depth of engraving 2 For a fine mark turn the stroke adjustment dial 3 anti clockwise to position 1 3 For a deeper thicker mark turn the stroke adjustment dial 3 clockwise to position 5 NOTE It is recommended that you practice on scrap material before you start Maintenance WARNING Always ensure that the tool is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures 1 Use a soft brush to remove any accumulated dust Wear safety glasses to protect your eyes whilst cleaning 2 If the body of the tool needs cleaning wipe it with a soft damp cloth A mild detergent can be used but never alcohol petrol or other harsh cleaning agents 3 Never use caustic agents to clean plastic parts CAUTION Water must never come into contact with the tool General inspection Regularly check that all the fixing screws are tight They may vibrate loose over time Power cord
14. GMC GLOBAL MACHINERY COMPANY AUW SOLDERING RON DECOOIS A ae A batt m Full 2 years home use warranty Whilst every effort is made to ensure your complete satisfaction with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use It also does not cover any bonus accessories unless the tool is a GMC Platinum Professional model Please ensure that you store your receipt in a safe place Conditions apply to the above warranty If you need direction of what constitutes a free of charge warranty claim please review the guide given on the rear of the Receipt Holder An indication is given as to the types o
15. aim spare part or user information please phone our Help Line 1300 880 001 Australia or 0800 445 721 New Zealand for an immediate response Product of China manufactured to exacting GMC quality standards ABN 68 093 174 808 The GMC 777 Helpline operates from 7am to 7pm 7 days a week EST This allows you to contact GMC directly with any queries and technical questions you have regarding our products Save this Manual for future reference AR REPLACEMENT WARRANTY GLOBAL MACHINERY COMPANY 45 55 South Centre Road Melbourne Airport Victoria Australia 3045 Tel 03 8346 1100 Fax 03 8346 1200
16. al before using your new GMC Power Tool Take special care to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate Environmental protection Recycle unwanted materials instead of ay disposing of them as waste All tools hoses a d and packaging should be sorted taken to the local recycling centre and disposed of in an environmentally safe way Description of symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use M8 Spindle thread for Collet nut L Read instruction manual Wear hearing protection Wear eye protection Wear breathing protection Double insulated for additional protection Conforms to relevant standards for electromagnetic compatibility 4 Variable speed dial 5 Spindle lock button 1 Cord protector 2 Wire loop 3 On off switch 6 Collet nut 7 Collet 8 Brush caps 9 Collet cover Specifications Input power 135W Power supply 230 240V 50 Hz No load speed 15000 35000min Collet size 2 4mm and 3 2mm M8 spindle Max Drill 3 2mm Max Grinding disc 25x 2mm Cord length 1 8 metres Tool weight 0 7 kg Flexible shaft length 1 0m Sound pressure level 83 dB A Sound power level 96
17. any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools e Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control e Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation Code DECO01SI Date 060113 op DCR Service e Have your power tool serviced by a qualified repair personnel using only identical replacement parts This will ensure that the safety of the power tool is maintained When operating a power tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock Additional safety instructions for soldering irons WARNING This tool must be placed on it s stand when not in use e Ensure this product is always used on a mains circuit protected by an earth e Always wear safety glasses when operating the soldering iron as solder may spit e When the soldering iron is not in use always return it to its stand e Always ensure the work area is both well
18. chniques it is unlikely that your GMC Power Tool is faulty or that a part is missing If you find anything wrong do not operate the tool until the parts have been replaced or the fault has been rectified Failure to do so could result in serious personal injury Accessories The GMC DEC002SD comprises the following components 1 Instruction manual 1 Battery charger 1 Magnetic bit holder 2 Interchangeable screwdriver bits Fitting and removing bits NOTE The drill bit supplied with the DECO002SD is not designed for use with the magnetic bit holder 1 To use the short drill bit supplied insert the bit directly into the chuck 1 as far as possible The drill is now ready to be used 2 To use the magnetic bit holder push the bit into the chuck 1 as far as possible The magnetic bit holder is compatible for use with most standard sized drill bits Forward Reverse switch NOTE This switch allows the direction of rotation of the chuck to be changed forward for driving and reverse for removing screws and nuts 1 Press the top of the forward reverse switch 2 for driving and press the bottom of the forward reverse switch to engage the reverse direction Adjusting the handle The handle can be turned to one of two positions to suit the task at hand The tool can be used as a straight handled screwdriver or as a pistol grip screwdriver 1 To change the position of the handle push the handle adjusting switch 3 forwa
19. dB A Vibration 0 482 m s Safety instructions WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings below refers to your mains operated corded power tool or battery operated cordless power tool Save these instructions Work area e Keep work area clean and well lit Cluttered and dark areas invite accidents e Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes e Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety e If cordset is damaged have it replaced by an authorised service centre e Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock e Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded e Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulli
20. e used indoors Maintenance Cleaning 1 Remove dust and dirt regularly Cleaning is best done with a rag 2 Never use caustic agents to clean plastic parts A mild detergent on a damp cloth is recommended Water must never come into contact with the tool CAUTION Disconnect the charger from the mains supply before cleaning Repairs 1 There are no user serviceable parts in this tool Only an authorised service centre should carry out repairs Givi C Full 2 Year Warranty This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use Consistent with our product development programme improvements may have been made which render the contents of the tool s packaging or user instructions slightly different to the product received Phone 03 8346 1100 Facsimile 03 8346 1200 Email info gmca co
21. e rating is harmful to the motor Switch on 1 Set the variable speed dial 4 to 1 and push the on off switch 3 to I the machine is in continuous operation and will start at minimum speed Switch off 1 Reset the variable speed dial 4 to 1 and push the on off switch 3 to position 0 Varying the speed 1 You can use the variable speed dial 4 to alter the speed of the collet as follows e Position 1 Slow Position 3 Medium e Position 6 Fast Select the correct speed for the work and type of bit you are using In general lower speeds are best suited for large accessories and higher speed for smaller accessories Quick reference guide NO Operation Speed e Cutting metal 5 6 e Sanding wood 5 6 e Cutting hard metal 5 6 e Engraving metal 4 5 e De burring 4 5 e Drilling holes 4 5 e Removing rust 3 4 Sharpening 3 4 e Polishing 1 2 Holding the tool 1 For jobs such as milling or engraving where precision is required hold the tool like a pen 2 For heavier work like cutting or grinding hold the machine in the palm of your hand Changing accessories 1 Make sure that the machine is switched off and the plug removed from the power before you commence changeover 2 Loosen and tighten collet fully using the 2 in 1 wrench provided always ensure bits are tight before commencing any work with your tool 3 Press and hold down the spindle lock button 5 and unscrew the Collet nut 6
22. entre should replace the cordset or effect other repairs If the cordset is damaged or worn have it repaired or replaced by an authorised service centre 2 When the brushes are worn the tool may not work Have new brushes fitted by an authorised service centre Please refer to your warranty card which is separate to these instructions Accessories For DEC003AC Kit Sanding Sanding drums are perfect for detailed sanding jobs 5 Coarse sanding sheets 20 mm diameter 5 Fine sanding sheets 20 mm diameter 5 Sanding bands 15 mm diameter Mandrels 1 Mandrel for sanding band 3 2 mm Diameter shaft 1 Disc mandrel for cut off wheel 3 2 mm Diameter shaft 1 Polishing pad mandrel 3 2 mm Diameter shaft Grinding The perfect way to remove burs and sharpen tools 5 Grinding stones Various shapes amp sizes Cutting Various cutting wheels let you cut trim and shape metal glass and ceramics 1 Ball shaped high speed cutter 1 Corn shaped cutter 8 Cut off wheels Polishing amp cleaning Ideal for removing rust smoothing out imperfections or cleaning tools 1 Polishing pads Felt 1 Polishing pads Felt 1 Bristle Brush Brass 1 Wire brush wheel Drilling An extremely convenient way to drill holes with more detail and precision 1 High speed drill bit 1 2 in 1 Wrench 2 Collets 1 Stone for dressing grinding wheels 2 4 mm Diameter shaft 2 4 mm Diameter shaft 24 mm Diameter 13 x 9mm 25 x 5 mm 3 2 mm Diameter shaft 3 2
23. er tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock This will ensure that the safety of the power tool is maintained Additional safety instructions for engravers Always wear eye ear and breathing protection Do not apply too much pressure when engraving WARNING The use of an accessory or attachment other than those recommended in this Instruction Manual may present a risk of personal injury To use this tool properly you must observe the safety regulations the assembly instructions and the operating instructions to be found in this Manual All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards Children and infirmed people must not use this tool Children should be supervised at all times if they are in the area in which the tool is being used It is also imperative that you observe the accident prevention regulations in force in your area The same applies for general rules of occupational health and safety The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors The following hazards may arise in connection with the tool s construction and design Damage to the lungs if an effective d
24. f claim that are permissible and those that are not Dear customer If you require any help with your product whether it is a Warranty claim spare part or user information please phone our Help Line for an immediate response Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand Introduction Your new GMC power tool will more than satisfy your expectations It has been manufactured under stringent GMC Quality Standards to meet superior performance criteria You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service Caution Carefully read through this entire Instruction Manual before using your new GMC Power Tool Take special care to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate Environmental protection Recycle unwanted materials instead of Qqy disposing of them as waste All tools hoses and packaging should be sorted taken to the local recycling centre and disposed of in an environmentally safe way 1 Solder tip 2 Solder tip release screw 3 Shaft 4 Flange 5 Rubber grip 6 Cord protector Description of symbols The rating plate on your tool may show symbols These represent important information about the product
25. g iron allowing the solder to melt onto the joint 4 Once the solder has been applied to the joint hold the workpiece still while removing the solder and soldering iron simultaneously NOTE A good solder joint will appear smooth and shiny If this is not the case you will need to reheat the joint and re apply the solder Removing the tip WARNING Do not attempt to remove the tip while the soldering iron is still hot 1 To help prevent the tip from bonding to the shaft which may cause the heater element to burn out it is recommended that the tip 1 be removed after each use 2 To remove the tip 1 clamp the soldering iron and apply two phillips head screwdrivers to the screws just above the soldering tip 2 and turn anti clockwise until the screws are loose and remove the tip Givi C Full 2 Year Warranty This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by
26. he charger and battery packs supplied with it are specifically designed to work together Do not attempt to charge the battery pack with any other charger than the one supplied Do not place any object on top of the charger as it could cause overheating Do not place the charger near any heat source Do not pull on the lead of the charger to disconnect it from the power source e Make sure that the charger cable is positioned where it will not be stepped on tripped over or otherwise subjected to damage or stress e Do not use an extension cord unless it is absolutely necessary The use of an improper extension cord could cause the risk of fire electric shock or electrocution e Do not use the charger if it has been subjected to a heavy knock dropped or otherwise damaged in any way Take the charger to an authorised service centre for a check or repair e Do not disassemble the charger Take it to an authorised service centre when service or repair is required Incorrect re assembly may result in the risk of fire electric shock or electrocution e To reduce the risk of an electric shock unplug the charger from the power supply before attempting to clean it Removing the battery alone does not reduce the risk e Never attempt to connect two chargers together e Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 104 F 40 C such as alongside sheds or metal structures in
27. he switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired e Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools e Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation Service e Have your power tool serviced by a qualified repair personnel using only identical replacement parts When operating a pow
28. ikely to bind and are easier to control e Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation Service e Have your power tool serviced by a qualified repair personnel using only identical replacement parts This will ensure that the safety of the power tool is maintained Additional safety instructions for rotary tools e Do not use a disc marked with a lower RPM than that of the maximum no load speed shown on the rating label Always wear eye ear and breathing protection Do not apply too much pressure when grinding cutting etc e Keep your hands well clear of the cutting devices WARNING The use of an accessory or attachment other than those recommended in this Instruction Manual may present a risk of personal injury To use this tool properly you must observe the safety regulations the assembly instructions and the operating instructions to be found in this Manual All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards Children and infirmed people must not use this tool Children should be supervised at all times if they are in the area in which the tool is being used
29. m au Website www gmcompany com Copyright Global Machinery Company Australia Proprietary Limited 2001 Dear customer if you require any help with your product whether it is a Warranty Claim spare part or user information please phone our Help Line 1300 880 001 Australia or 0800 445 721 New Zealand for an immediate response Product of China manufactured to exacting GMC quality standards ABN 68 093 174 808 operates from 7am to This allows you to contact GMC directly with any queries and technical questions you have regarding our products Save this Manual for future reference The GMC 777 Helpline YEAR REPLACEMENT WARRANTY GLOBAL MACHINERY COMPANY 45 55 South Centre Road Melbourne Airport Victoria Australia 3045 Tel 03 8346 1100 Fax 03 8346 1200 GMC GLOBAL MACHINERY COMPANY lda W AL ROTARY TOOL DECGOOSALC Full 2 years home use warranty Whilst every effort is made to ensure your complete satisfaction with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may
30. mm Diameter shaft 3 2 mm diameter 2 4 mm and 3 2 mm 26 x 10 x 10 mm GiVi C Full 2 Year Warranty This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use Consistent with our product development programme improvements may have been made which render the contents of the tool s packaging or user instructions slightly different to the product received Phone 03 8346 1100 Facsimile 03 8346 1200 Email info gmca com au Website www gmcompany com Copyright Global Machinery Company Australia Proprietary Limited 2001 Dear customer if you require any help with your product whether it is a Warranty Claim spare part or user information please phone our Help Line 1300 880 001 Australia or 0800 445 721 New Zealand for an immediate response Product of China manufactured to exacting GMC
31. n force in your area The same applies for general rules of occupational health and safety The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors The following hazards may arise in connection with the tool s construction and design e Damage to the lungs if an effective dust mask is not worn e Damage to hearing if effective ear defenders are not worn Additional safety instructions for the charger e Before using the charger read all the instructions and cautionary markings on the charger and battery pack as well as the instructions on using the battery pack e Only charge your batteries indoors as the charger is designed for indoor use only e DANGER If the battery pack is cracked or damaged in any other way do not insert it in the charger There is a danger of electric shock or electrocution e WARNING Do not allow any liquid to come into contact with the charger There is a danger of electric shock e To allow the battery pack to cool down after charging do not place it in a hot environment such as a metal shed or open trailer left in the sun e The charger is not intended for any use other than charging the exact type of rechargeable battery pack as supplied with the charger Any other use may result in the risk of fire electric shock or electrocution e T
32. ng or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock Personal safety e Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury e Use safety equipment Always wear eye protection Safety equipment such as a dust mask non skid safety shoes hard hat or hearing protection use Code DEC003 Date 060113 Op DCR d Q e Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents e Remove any adjusting key or wrench before turning the tool on A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations e Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away f
33. nit For safety please ensure the unit is well minded until it has entirely cooled down Preparing to solder WARNING Always use safety glasses and ensure the work area is well ventilated to help avoid breathing in dangerous fumes The GMC Soldering Iron is typically used to melt and apply solder on various surfaces including circuit boards 1 Before beginning to solder secure the work piece so that it does not move and affect your accuracy 2 Prepare a damp sponge nearby to clean the tip when required 3 Melt a small amount of solder onto the tip of the iron 1 This process is known as tinning and will assist the heat in following from the soldering iron s tip to the solder joint It is important to do this immediately with new soldering tips 3 Ensure that the workpiece and soldering tip are clean The workpiece can be cleaned with the use of a small file or knife blade It is recommended that the user wipe clean the soldering tip with a damp sponge before during and after soldering This will help promote a cleaner and stronger solder joint Soldering 1 Hold the soldering iron close to the base of the handle 5 and just above the flange 4 like a pen WARNING Never touch the shaft 3 or tip 1 as temperatures can range up to 400 C 2 Hold the soldering iron with the tip pressed onto the workpiece for a few second to allow it to heat up 3 Slowly feed the solder onto the joint not the solderin
34. nto the collet 7 until the cable cannot go any further 3 Tighten the collet nut 6 with the wrench by turning the nut clockwise 4 Thread the flexible shaft collet cover onto the tool housing by turning it clockwise and finger tighten only WARNING Never tighten the collet nut with the use of pliers or a wrench as the thread will strip Changing the collet and accessories Note To change the collet or install a cutter or accessory into the flexible shaft follow the same general procedure as covered earlier under Changing accessories WARNING Do not attempt to loosen the collet nut without pulling the spindle lock back as far as possible Damage to the flexible shaft will result 1 To lock the spindle lock pull the lock back as far as possible 2 Use the wrench to loosen and tighten the collet nut Maintenance 1 Store the machine instruction manual and where necessary the accessories in the original packaging In this way you will always have all the information and parts ready to hand Cleaning 1 Keep the tool s air vents unclogged and clean at all times 2 Remove dust and dirt regularly Cleaning is best done with a rag 3 Never use caustic agents to clean plastic parts CAUTION Do not use cleaning agents to clean the plastic parts of the tool A mild detergent on a damp cloth is recommended Water must never come into contact with the tool Repairs 1 Only an authorised service c
35. on with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use It also does not cover any bonus accessories unless the tool is a GMC Platinum Professional model Please ensure that you store your receipt in a safe place Conditions apply to the above warranty If you need direction of what constitutes a free of charge warranty claim please review the guide given on the rear of the Receipt Holder An indication is given as to the types of claim that are permissible and those that are not Dear customer If you require any help with your product whether it is a Warranty claim spare part or user information please phone
36. or instructions on its use Wear hearing protection Wear eye protection Wear breathing protection Conforms to relevant standards for electromagnetic compatibility Specifications Input power 30W Power supply 230 240V 50 Hz Shaft material Stainless steel Solder tip Nickel coated Cord length 1 4 metres Tool weight 0 2 kg Safety instructions WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings below refers to your mains operated corded power tool or battery operated cordless power tool Save these instructions Work area e Keep work area clean and well lit Cluttered and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes e Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety e If cordset is damaged have it replaced by an authorised service centre e Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock e Avoid body contact with earthed or grounded surfaces s
37. ove sawdust chips or waste close by the bit e Rags cloths cord string and the like should never be left around the work area Support the work properly e If you are interrupted when operating the drill complete the process and switch off before looking up e Periodically check that all nuts bolts and other fixings are properly tightened When using the drill use safety equipment including safety glasses or shield ear defenders and protective clothing including safety gloves Wear a dust mask if the drilling operation creates dust If in doubt do not plug in the tool Using a power source with a voltage less than the nameplate rating is harmful to the motor The tool must be used only for its prescribed purpose Any use other than those mentioned in this Manual will be considered a case of misuse The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse To use this tool properly you must observe the safety regulations the assembly instructions and the operating instructions to be found in this Manual All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards Children and infirmed people must not use this tool Children should be supervised at all times if they are in the area in which the tool is being used It is also imperative that you observe the accident prevention regulations i
38. pheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes e Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety If cordset is damaged have it replaced by an authorised service centre e Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock e Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock e Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock Personal safety e Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs
39. quality standards ABN 68 093 174 808 operates from 7am to This allows you to contact GMC directly with any queries and technical questions you have regarding our products Save this Manual for future reference The GMC 777 Helpline AR REPLACEMENT WARRANTY GLOBAL MACHINERY COMPANY 45 55 South Centre Road Melbourne Airport Victoria Australia 3045 Tel 03 8346 1100 Fax 03 8346 1200 GMC ELECTRIG lt ENGRAVER DECOOEN 4 3 Stroke adjustment dial 4 Tip release screw Full 2 years home use warranty Whilst every effort is made to ensure your complete satisfaction with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accident
40. r of cutting devises Unpacking Due to modern mass production techniques it is unlikely that your GMC Power Tool is faulty or that a part is missing If you find anything wrong do not operate the tool until the parts have been replaced or the fault has been rectified Failure to do so could result in serious personal injury Operation WARNING Before connecting a tool to a power source be sure that the voltage supply is the same as that specified on the nameplate of the tool A power source with a voltage greater than that specified for the tool can result in serious injury to the user as well as damage to the tool If in doubt do not plug in the tool Using a power source with a voltage less than the nameplate rating is harmful to the motor Setting up the iron stand 1 By firmly holding the stand with both hands press the centre of the stand in so that it separates itself from the rest of the stand and bend to approximately 45 from the base Switch on 1 Ensure the soldering iron is resting securely on the iron stand before plugging in to the power 2 After switching on the power allow the tool a few minutes to heat up to its operating temperature Switch off 1 It is highly recommended that the soldering tip is wiped clean on a damp sponge not included after use to prolong service life and performance 2 Place the soldering iron securely on its stand Switch off the tool at the power switch and unplug the u
41. rd and twist the handle to the desired position 2 Release the switch 3 to lock the handle in the new position Recharging the screwdriver Your screwdriver is supplied to you partially charged and must be fully charged before use For the first charge we recommend charging for 10 to 12 hours 1 Connect the charger plug to the charging socket 4 2 Connect the mains plug of the charger to a suitable power point 3 The indicator light 5 illuminates to show that charging is taking place NOTE Whilst charging the charger and the screwdriver may become warm to touch This is normal and does not indicate a problem NOTE The charger will not automatically switch off when the battery is fully charged and the indicator will remain on WARNING It is important to unplug the charger from the screwdriver when the charging time has been completed DO NOT EXCEED 12 HOURS CHARGING TIME It will damage the battery 3 After the initial charge recharge the battery for 5 to 7 hours when the battery is completely discharged Do not top up the battery when it is partially discharged 4 Charging for 7 hours increases the length of time the tool can be used WARNING Do not leave your screwdriver on charge continuously This will damage the battery NOTE Avoid charging your screwdriver in temperatures below 4 C and over 40 C The ideal temperature at which to charge the tool is 20 C The battery charger should only b
42. rom moving parts Loose clothes jewellery or long hair can be caught in moving parts e If devices are provided for the connection of dust extraction and collection facilities ensure that these are connected and properly used Use of these devices can reduce dust related hazards Power tool use and care e Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired e Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally e Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools e Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less l
43. roperly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts e If devices are provided for the connection of dust extraction and collection facilities ensure that these are connected and properly used Use of these devices can reduce dust related hazards Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired e Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools e Keep cutting
44. s alterations or commercial or business use It also does not cover any bonus accessories unless the tool is a GMC Platinum Professional model Please ensure that you store your receipt in a safe place Conditions apply to the above warranty If you need direction of what constitutes a free of charge warranty claim please review the guide given on the rear of the Receipt Holder An indication is given as to the types of claim that are permissible and those that are not Dear customer If you require any help with your product whether it is a Warranty claim spare part or user information please phone our Help Line for an immediate response Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand Introduction Your new GMC power tool will more than satisfy your expectations It has been manufactured under stringent GMC Quality Standards to meet superior performance criteria You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service Caution Carefully read through this entire Instruction Manual before using your new GMC Power Tool Take special care to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate 1 On off switch 2 Engraving tip 5
45. the summer e The charger is designed for use from a standard household electrical supply 230 240 volts Do not attempt to connect the charger to a supply with a different supply e If you wish to charge a second battery pack unplug the charger from the mains supply and leave it for at least 15 minutes After this time you can charge a second battery pack Additional safety instructions for the battery pack e The battery pack for this tool has been shipped in a low charge condition You should charge the battery pack fully before use e To ensure the longest battery life and best battery performance always charge the battery when the air temperature is between 18 24 C Do not charge the battery pack when the temperature is below 4 C or above 40 C This is important Failure to observe this safety rule could cause serious damage to the battery pack e Do not incinerate the battery pack even if it is seriously damaged or can no longer hold a charge The battery pack can explode in a fire e Never attempt to open the battery pack for any reason If the plastic housing of the battery pack breaks open or cracks immediately discontinue its use and do not recharge it e The battery pack utilizes nickel cadmium cells Cadmium is considered to be a toxic material Use an environmentally safe disposal unit at a municipal waste disposal centre to dispose of a damaged or worn out battery Unpacking Due to modern mass production te
46. tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control e Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation Service e Have your power tool serviced by a qualified repair personnel using only identical replacement parts This will ensure that the safety of the power tool is maintained Additional safety instructions for drills e f possible always use clamps or a vice to hold your work e Always switch off before you put the drill down e Ensure that the lighting is adequate Date 060113 Edition 08 Op DCR e Do not put pressure on the drill such that it slows the motor down Allow the drill bit to cut without pressure You will get better results and you will be taking better care of your tool e Keep the area free of tripping hazards e Do not let anyone under 18 years operate this tool e Only use accessory bits in good condition e Before drilling check that there is sufficient clearance for the drill bit under the workpiece e Do not touch the bit after operation It will be very hot e Keep your hands away from under the workpiece e Never use your hands to rem
47. uch as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock e Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury e Use safety equipment Always wear eye protection Safety equipment such as a dust mask non skid safety shoes hard hat or hearing protection use e Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents e Remove any adjusting key or wrench before turning the tool on A wrench or a key that is left attached to a rotating part of the power
48. ust mask is not worn Damage to hearing if effective earmuffs are not worn e Damage to eyes if effective goggles are not worn e Risk of injury unless hands are kept well clear of cutting devices Unpacking Due to modern mass production techniques it is unlikely that your GMC Power Tool is faulty or that a part is missing If you find anything wrong do not operate the tool until the parts have been replaced or the fault has been rectified Failure to do so could result in serious personal injury Installing an engraver tip WARNING Disconnect the engraver from the power supply before making any adjustments or maintenance procedures 1 Loosen the tip release screw 4 by turning it anti clockwise with a flat head screwdriver 2 To fit the new engraving tip 2 insert the tip through the centre of the hole of the engraver ensuring the tip fully enters the housing A new tip should protrude from the end of the housing by approximately 8 5mm 3 Tighten the tip release screw 4 fully by rotating in a clockwise direction Operation WARNING Always wear safety glasses when using this tool The GMC engraver can be used to permanently mark metal glass plastic wood ceramics and much more 1 Before using the engraver you must ensure there is an engraving tip installed 2 Connect the engraver plug to the power supply and while holding the engraver firmly push up on the on off switch 1 with your thumb NOT
Download Pdf Manuals
Related Search