Gefen CAT-5 DA User's Manual
Contents
1. 1x8 Component CAT 5 DA USER MANUAL WWW gefen com ASKING FOR ASSISTANCE Technical Support Telephone 818 884 6294 800 545 6900 Fax 818 884 3108 Technical Support Hours 9 00 AM to 5 00 PM Monday thru Friday Write To Gefen Inc C O Customer Service 6265 Variel Ave Woodland Hills CA 91367 9897 Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice 1x8 Component CAT5 DA is a trademark of Gefen Inc O 2006 Gefen Inc All Rights Reserved 10 TABLE OF CONTENTS Operation Notes Introduction Features Sender Panel Descriptions Receiver Panel Descriptions Connecting and Operating the 1x8 Component CAT5 DA How to Adjust the Picture CAT5 Wiring Diagram Specifications Warranty OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 1X8 COMPONENT CAT5 DA SYSTEM e Use industry standard Category 5 CAT 5 cable to operate the 1x8 Component CAT5 DA system CAT 5e cable is preferred e Please connect all the cables between the computer and the 1x8 Component CAT5 DA system before powering up the 1x8 Component CAT5 DA Sender unit e The 1x8 Component CAT5 DA units are housed in a metal box for better RF shielding INTRODUCTION Congratulations on your purchase of the exetendsit 1x8 Component CAT5 Distribution Amplifier Your complete satisfaction is very important to us Gef2. S Features e Distributes easily up to eight Component displays e Extends each display up to 330 feet e Maintains 480i 480p 720p 720i and 1080i 1080p resolutions e Distributes and extends Component or VGA video signals e Installs in seconds Includes The 1x8 Component CAT5 DA One 6 VGA to Component cable 5V6A DC Power Supply Users Manual SENDER PANEL DESCRIPTIONS 18 CAT 5 Distribution Power LED 1 8 COMPONENT Made In U S A Gefen Inc Te Ee CAT 5 Video Out awe A Connects to Video CAT5 VGA to Component Video CAT5 5VDC power Out 1 4 Cable Input Out 5 8 supply RECEIVER PANEL DESCRIPTIONS EQ Video Power VGA to Component Knob CAT5 In LED Cable Out Connecting and Operating the 1x8 Component CAT5 DA How to Connect the 1x8 Component CAT5 DA to your devices 1 Connect the supplied VGA to Component cable from the Component video source into the 1x8 Component CAT5 DA Sender Comp In port 2 Connect a CAT 5e cable from the CAT5 Video Outs on the 1x8 Component CAT5 DA Sender to the CAT5 Inputs on the Component CAT5 Distribution Receiver Repeat for each Receiver unit 3 Connect the VGA to Component cable from the display to the Comp Out on the Component CAT5 Distribution Receiver Repeat for each Receiver unit 4 Plug the 5VDC power supply into the 1x8 Component CAT5 DA Sender HOW TO ADJUST THE PICTURE The first step in adjusting the video quality is to display text an
3. cid ee HD 15 Output onnar Type pss ee HD 15 Link pe anne Bada a aaa adas RJ 45 Power CONSUMO ee ae 30 Watts max Power NY ern ee een ehe 5VDC DIMENSIONS esseri a Rabia 8 5 VV x 1 75 H x 4 5 D 12 MAE ba AD iia 3 Lbs WARRANTY Gefen Inc warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen Inc is notified within one 1 year from the date of shipment Gefen Inc will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed The information in this manual has been carefully checked and is believed to be accurate However Gefen Inc assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen Inc be liable for direct indirect special incidental or consequential damages resulting from any defect
4. d a graphic on your monitor i e desktop icons Then set your computer to the resolution that you will be using most frequently The dip switches are used to set the focus and sharpness of the picture to the best possible setting Set the dip switches to the settings that are recommended for the different lengths of CAT5 cable see chart below Verify that the picture quality is to your satisfaction If the recommended setting does not produce a great quality picture try using a different dip switch setting The trim pod next to the Component connector on the 1x8 Component CAT5 DAR allows brightness adjustments for video 0 25 Feet All dip switches OFF for all colors 26 100 Feet Set dip switch 1 ON all colors 2 3 4 remain OFF 101 200 Feet Set dip switch 2 ON all colors 1 3 4 remain OFF 201 300 Feet Set dip switch 3 ON all colors 1 2 4 remain OFF 301 Feet and Up Set dip switch 4 ON all colors 1 2 3 remain OFF NOTE The dip switches are set to the OFF position when the switch is closest to the number or in the down position CAT5 WIRING DIAGRAM UMOJ9 SUUYM 9N 9 9UUM U H HUAA 2BUBIO ebueio euuM yoer Gb Py Sr ry SPECIFICATIONS Video Amplitier Bandwidth nu ee is 350 MHz Aput Video Signale 1 2 volts p p Mp t DDC Signalen ade 5 volts p p TTL Horizontal Frequency Range een 15 70 KHz Vertical Ffeduenc Range nn iia 30 170 KHz A 1080p 1920 x 1200 Input C nne
5. en s line of Home Theater switchers extenders and Distribution Amplifiers are de signed to make your A V setup more comfortable more productive and more affordable The 1x8 Component CAT5 DA allows one Component source to be distributed on up to eight displays The 1x8 Component CAT5 DA also extends Component signals over 330 feet using industry standard Category 5 CAT 5 Cable All output displays will have mirrored images The exetendeit line offers solutions for home theater A V installation data center infor mation distribution conference room presentation school and corporate training envi ronments Our Commitment Gefen will always offer the finest quality product at the best possible price Included in that price is a lifetime support from a team of outstanding engineers How it Works Simply connect your Component video source to the 1x8 Component CAT5 Distribu tion Amplifier s input using the supplied VGA to Component cable Then connect up to eight Component displays to the Component CAT5 receivers over 330 feet using CAT 5 Cable Then power the 1x8 Component CAT5 Distribution Amplifier and the receivers will get power from the CAT5 Note Component output 1 is the primary connection and is used for the main display Component output 2 through 8 follow the main display The Component displays attached to the 1x8 Component CAT5 Distribution Amplifier MUST have the same native resolution in order to get a picture FEATURE
6. or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding 1x8 Component CAT5 DA features and specifications is subject to change without notice 10
Download Pdf Manuals
Related Search