Geemarc Clearview Cordless Caller Display Unit User's Manual
Contents
1. to next character When all characters are OK press Set to select next entry to be edited by using Review Forward or Backward 10 Press Timer to quit editing o OND AMBROS N In case of difficulty What to do if CHECK BASE is seen on Clearview display This means that the base is disconnected or the ID code was not set properly or the Clearview display is out of range Check base is connected to telephone modular socket verify ID code or move the Clearview display closer to the base and press Page to confirm in range How to change the base identification code Your base comes with a random identification generated at the factory Should you want to change it press Set then Page and keep both keys depressed for 5 seconds until the new random code is shown Remember you must then set your Clearview display to this new code Care of your Clearview Cordless Caller Display The Caller Display should be cleaned with a soft dry cloth Itis important to unplug the main base unit from the mains supply and telephone socket prior to cleaning Do not apply polishes or strong cleaning agents as these could damage the moulding THUNDERSTORMS During thunderstorms lightning may strike telephone lines this can damage any equipment attached to a line including telephones and telephone equipment If possible unplug your telephone or telephone equipment from the socket in the event of a storm Conditions of use Your Geemarc Clearvie2. S YOUR GUARANTEE Please note The guarantee applies to the United Kingdom only Geemarc reserve the right to modify the design and specification of the product and related equipment in line with our policy of continuous product improvement Geemarc Telecom Ltd 5 Swallow Court Swallowfields Welwyn Garden City Hertfordshire AL7 1SB Helpline 01707 384438 Facsimile 01707 372529 Clearview Cordless Caller Display Unit User Guide Introduction Thank you for choosing Geemarc s Clearview Cordless Caller Display Please read the instructions carefully before use and keep this User Guide for future reference The Clearview stores up to 60 names and numbers in its call list The display is extra large allowing you to read it from across the room without the need to walk to the display Also it serves as a jumbo LCD clock which never has to be set since it is set automatically by the caller ID information The Clearview can also hold a directory of 50 names and numbers If an incoming number matches a record the assigned name such as FATHER OFFICE etc will be mapped and shown on the display You can build up your own directory The Clearview can cover a range of up to 20 metres from the base in a typical household environment Note Consult your PABX supervisor before fitting this product to a PABX facility Caller Display service Your Clearview Cordless Caller Display receives and displays caller information whi
3. Setting options for Clearview Cordless Caller Display You may select the LCD contrast level factory setting as level 2 the call alert tone either On or Off factory setting is Off the clock either 12 or 24 hour format factory setting is 24 hour and the alarm clock either On or Off factory setting is Off 1 Press Set for 5 seconds until you see OPTIONS 2 Press Review Forward repeatedly to scroll through current option settings 3 Any time you wish to change a setting press Set 4 The last section in this option mode is name setting If you want to exit from the option mode simply press Review Forward Press Set to enter name setting for phone directory see section below Alarm clock setting Press Timer for 5 seconds until you see ALARM ON or OFF Press Set to toggle the On Off setting When Alarm On press Review Forward or Backward to show the current alarm time setting and press Set if you want to change it Use Review Forward or Backward to scroll the hour and Learn to advance to minute When the alarm time setting is OK press Set to finish setting and you will hear a confirmation beep Note When the alarm has been set to On a symbol appears at the bottom right corner of the display When the alarm is activated it will beep for 1 minute Press any key to stop the alarm The alarm will operate at the same time the next day unless it is set to off See setting options above o e eh Nam
4. ch is transmitted over the BT network or other network providers The information will include the date and time the call is received And in most cases the caller s phone number Note To enable your Clearview Cordless Caller Display to display information transmitted via BT or other UK network providers you will first have to subscribe to that networks Caller Display Service Please contact your network service provider to arrange this service Installation Position your Clearview Cordless Caller ID Base Unit within 2 metres of a telephone socket Do not stand your Clearview Cordless Caller ID display or Base Unit on carpets or other similar surfaces which might generate fibres Do not expose the units to high temperatures by siting near radiators etc Keep the units dry and do not operate in outdoor conditions Do not cover or enclose the machine Allow a free flow of air to its surfaces NOTE We advise that the units be placed on a table cloth or similar as rubber feet can mark some surfaces Connect the adaptor to the base unit Plug the adaptor into the mains socket and connect the small plug into the 9YAC DC socket at the rear of the Clearview base unit Switch on the supply NOTE Do not attempt to use or replace the mains adaptor supplied with this product other than a Geemarc AC DC adaptor type 09200DG Connect the line cord Connect the small plug on the line cord into the Line Cord In socket Connect other end of line cor
5. d into the telephone socket To connect a telephone to your Clearview Cordless Caller Display base unit plug the telephone line cord into the spare socket of the doubler at the end of the Clearview line cord Should you not have a modular telephone socket as shown please contact your local British Telecom or other Network Operator For moving through the Directory list calls list or between digits characters when entering a number Used to delete all of anumber or just part of it Used to set and store information Used to code display Used to operate timer and alarm clock setting unit advance digits and characters in settings ecemarc Telecom Helpline 01707 384438 Setting up the base unit Press Set for 5 seconds until you see OPTI 2 Press Page for language setting Press Set to select ENG English SVE Swedish DAN Danish SUO Finnish 3 Press Page again to show TIME Press Page twice the date and time setting will be automatically updated each time you receive a call Setting up the display unit Insert Batteries to Clearview Cordless Caller Display Open the battery compartment on the underside of your Clearview Cordless Caller Display by pushing it towards the back edge You will need 4 x AA alkaline batteries NOT INCLUDED WARNING Calls list back up time is 1 minute Do not remove all batteries or the stored memories may be lost To i
6. e setting for Phonebook Directory for name mapping 50 entries 1 At the last part of the option mode the display shows NAME SETTING Press Set Press Review Forward or Backward to scroll to the record that you want to input Press Set to select the record The display will show the record number and 0 in the telephone number field Use Review Forward or Backward to select the digit Learn to advance to next digit Delete for correction When all digits are OK press Set to jump to the name field Press Review Forward or Backward to select the character Press Learn to advance to next character When all characters in the name are OK press Set to finish this record setting and you will hear the confirmation beep The display will advance to the next record 8 Press Timer to quit the name setting mode Note Phonebook directory entries cannot be deleted but can be changed by editing them N ea A SP Editing a phonebook directory entry At the last part of the option mode the display shows NAME SETTING Press Set Press Review Forward or Backward to scroll to the record that you want to change Press Set to select the record Press Delete until number is erased Use Review Forward or Backwards to select the digit Learn to advance to next digit When all digits are OK press Set to jump to name field Press Delete until name is erased Use Review Forward or Backwards to select the character Learn to advance
7. ensure the memories are not lost users should take out one a battery at a time and replace with a new one before taking out the next battery Change all 4 batteries when the battery low symbol shows in the display NOTE The directory memory is non volatile and will not be lost when changing batteries Operation Setting Clearview Cordless Caller Display identification ID code The Clearview Display must be set with the same identification ID code as the base The Clearview display will read SET CODE after inserting the four AA alkaline batteries 1 Place Clearview display next to base 2 On the Clearview display press Learn The display will read LEARN 3 Onthe base press Page within 10 seconds This sends the base ID code to the Clearview display To indicate that the ID code has been properly set the Clearview will beep and its display will read ID SET Verifying that the Clearview display is within range of the base When Page is pressed at the base if the Clearview display is within range it will beep once and the display will show PAGE RECEIVED for 30 seconds If it does not show PAGE RECEIVED then move the Clearview display closer to the base and repeat the previous steps If it still does not beep repeat the steps above to verify that the identification code has been properly set Press Review Forward or Backward to scroll through the records To view records in the call list T
8. o delete a record When viewing the record press Delete from the the call list To delete all records Press Delete for 5 seconds until you see the from the call list message indicating that there are no total calls Using the timer To start or stop the timer press Timer After Stop the timer display will freeze for 5 seconds UG CLEARVIEW CORDLESS Issue 1 09 00
9. w Cordless Caller Display has been approved for use on private direct exchange lines and business lines It is also approved for use with approved compatible PABX s Your exchange line should be a standard exclusive DEL and not a shared service or party line Your line should be Multi Frequency TONE dialling If you experience any difficulty contact your network service provider Approval This product complies with the requirements of EC directive 89 336EEC Any modification of the unit or connection to non approved accessories may affect this compliance Guarantee From the moment your Geemarc product is purchased Geemarc Telecom Ltd guarantee it for one year During this time all repairs or replacements at our option are free of charge Carriage to Geemarc is payable by the sender The guarantee does not cover accidents negligence or breakages to any parts The unit parts must not be tampered with or taken apart by anyone who is not an authorised Geemarc representative The guarantee of Geemarc Telecom Ltd in no way limits your legal rights Should you experience a problem then contact our helpline or the retailer from whom you purchased your Geemarc product If you do have to return the product to Geemarc Telecom Ltd please enclose a note of your name and address with details of the problem being experienced Also enclose a copy of your purchase receipt and a cheque for 5 to cover return postage and packing YOUR RECEIPT I
Download Pdf Manuals
Related Search