GE SAM Installation Guide
Contents
1. orient the photoelectric receptacle See illustration 3 ILLUSTRATION 3 Grasp spring loaded PE control receptacle P and lift up rotate receptacle clockwise until North arrow Q printed on top of receptacle points North Reseat receptacle If this orientation prevents light from reach ing control window R rotate arrow to point South P Lift Twist and Reseat To install the photoelectric control S See illustration 4 ILLUSTRATION 4 Insert the PE control S in its proper keyed socket slots on top of fixture making certain that the largest of the three prongs is inserted onto the slot located adjacent to the word North on the socket Press downward and twist clockwise about 1 8 of a turn to secure Wiring NOTE Make all electrical connections in accordance with the National Electrical Code and any applicable local code requirements including grounding NOTE Verify that supply voltage is correct by comparing it to nameplate Terminals are readily accessible on terminal board and will accept service leads ranging in size from AWG No 16 through No 6 Service leads FOR Special option catalog number with 240 volt primary ballast operation and 120 volt PE operation Connect incoming 240 volt to fixture black wires and connect the incoming white wire to the fixture white wire Lamp Installation CAUTION Risk of burn Allow lamp fixture to cool before handling NOTE Use on2. GE Lighting Solutions GEH 5982 INSTRUCTIONS Type 201 SA Luminaire READ THOROUGHLY BEFORE INSTALLING A WARNING Risk of electric shock e Turn power off before servicing see instructions Ay CAUTION Risk of burn e Do not touch operating luminaire CAUTION Risk of injury e Wear safety glasses and gloves during installation and servicing CAUTION Type 201 SA luminaire is designed for outdoor lighting and should not be used in areas of limited ventilation or in high ambient temperature enclosures ILLUSTRATION 1 Nut Square Washer i Thru Bolt H E _ A H i i M Extension Arm iff D H H i i Lag Bolts 4 omw 3 D i i Mounting Bracket wg _ Type 201SA Conduit Mounting a A CAUTION Unit will fall if not installed properly e Follow installation instructions Type 201 SA luminaire unit pack is designed for mounting on a round wood pole See above illustration for identification and location of parts The mounting bracket should first be mounted to pole A clearance hole for a 5 8 inch diameter bolt must be drilled through pole The 10 inch through bolt should be inserted through clearance hole and 2 inch square washer and nut screwed loosely onto opposite end of through bolt The pole plate on mounting arm should be placed over square head of through bolt so that square head is engaged by two indented tabs on po
3. le plate See illustration 1 SEE ILLUSTRATION 2 Nut should be tightened down so that mounting bracket arm is securely attached to pole Lag bolts should be inserted into outside lower holes of mounting bracketarm pole plate Hammer lag bolts in to within approximately 1 of head then tighten down with wrench ILLUSTRATION 2 The leads from hood should first be inserted through outboard end of the mounting bracket and brought out through inboard end adjacent to the pole plate It is recommended a drip loop be formed where leads exit mounting bracket as indicated in above drawing Check to see if opening of mounting bracket arm clamp in slip fitter is large enough to allow mounting bracket to be inserted If not loosen two clamp bolts until opening is large enough The slip fitter is then inserted over outboard end of mounting arm mounting arm being inserted until it comes to rest at pipe stop on inboard end of slip fitter approx 2 inches Once mounting bracket is fully inserted level hood with mounting bracket clamp relatively loose by placing outboard end of mounting bracket on appropriate step of leveling pipe stop then tighten two clamp bolts securely taking care not to disturb position of hood torque should be approx 10 15 foot pounds NOTE The mounting bracket clamp is factory installed for use with a 1 inch pipe If a 2 inch pipe is being used it will be necessary to flip the mounting arm clamp over To
4. ly lamps specified on nameplate Observe lamp manufacturer s recom mendations and restrictions on lamp operation particularly ballast type burning position etc Installation of optical assembly to hood Optical assembly should be handled carefully to prevent damage from surface abrasion or severe impact Attach optical assembly to hood by snapping two latches on reflector to ears on hood ILLUSTRATION 5 See illustration 5 These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes the matter should be referred to GE Lighting Solutions GE Lighting Solutions e 1 888 MY GE LED e www gelightingsolutions com 1 888 69 43 533 GE Lighting Solutions is a subsidiary of the General Electric Company Evolve and other trademarks belong to GE Lighting Solutions The GE brand and logo are trademarks of the General Electric Company 2011 GE Lighting Solutions Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions 35 201578 174 8 08
Download Pdf Manuals
Related Search