GE r10279v User's Manual
Contents
1. Installation Instructions TOOLS REQUIRED e 2 Phillips screwdriver e Adjustable wrench PARTS SUPPLIED e Monogram nameplate e Hardware for changing door swing e Optional stainless steel toekick with screws and spacers e Left and right side hinge covers e Top screw hole cover GROUNDING THE WINE CHILLER WINE RESERVE AND BEVERAGE CENTER IM PORTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded Where a standard 2 prong wall outlet is encountered it iS your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2 PRONG OUTLET DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE STAINING WOOD DRAWER FRONTS The drawer fronts are unfinished cherry wood During use oil from hands may accumulate and stain the wood e The drawer fronts may be stained and sealed to match adjacent cabinetry The tinted glass will make the staine2. e Tubular handle e 2 Mounting screws e 2 Handle standoffs e 2 Set screws for standoffs e 2 Nuts e 2 Washers e Allen Wrench Custom Framed Panel Tubular Handle Handle Standoff Washer Handle Attachment Nut Post Set Screw TEMPLATE FOR NAMEPLATE LOCATION Upper Left Corner of Glass if Hinge is on Left lt Door Frame Side reg pokes To position nameplate e Cut template along dotted line e Hold or tape template behind glass door so that it is visible from the front side e Remove backing from nameplate e Place nameplate onto front side of door matching illustration on the template IMPORTANT Nameplate must be placed on the opposite side of the door handle Note While performing installations described in this book Top of Glass Door Top of Badge Monogram DOOR NAMEPLATE LOCATION safety glasses or goggles should be worn For Monogram local service in your area call 1 800 444 1845 Note Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice Pub No 31 46122 2 Part No 197D7840P001 12 07 JR Printed in Slovenia Upper Right Corner of Glass if Hinge is on Right Door Frame Side p gt GE Consumer amp Industrial Appliances
3. General Electric Company Louisville KY 40225 ge com
4. allow racks to slide out Allow 10 minimum clearance on the hinge side for a full 110 door swing Models ZDWI240WIl and ZDBI240WIII have a 95 door swing NOTE Custom handle clearances may vary depending on custom handle depth 10 Minimum 90 Door Swing to Wall ely 1100 r A a 4 Minimum 95 Door Swing on Custom Frame Models to Wall e The door swing is reversible on all models If desired change the door swing before installation or before installing the custom fram panel Choose the location e These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door Do not install these products where the temperature will go below 55 F 13 C or above 90 F 32 C Do not install where it will be subject to direct sunlight heat or moisture e These products are not designed to be stacked one over the other Black or Stainless Steel Toekick Options e These products are shipped with a black toekick installed An optional stainless steel toekick is also supplied with each product For shipping purposes the stainless steel toekick is secured to the back of the unit ZTBSS1 Tubular Handle ZTBSS1 Monogram stainless steel tubular handle is available for models ZDWI240WII and ZDBI240WII Locate Outlet 0 1 2 10 1 2 e1 4 oe tt 34 1 2 35 Bg 15 WA 47 1 2 Min
5. e If installing between frameless cabinets a 1 2 wide filler strip or side panel may be needed on hinge side The filler strip will act as a spacer between the case and adjacent cabinet door swing The width of the opening must include the filler panels NOTE The door should protrude 1 beyond the surrounding cabinets Custom framed models will protrude 1 7 8 beyond surrounding cabinet doors Additional Specifications e A 120 volt 60Hz 15 or 20 amp power supply is required An individual properly grounded branch circuit or circuit breaker is recommended Install a properly grounded 3 prong electrical receptacle recessed into the back wall as shown Electrical must be located on rear wall as shown NOTE GFI ground fault interrupter is not recommended SIDE BY SIDE INSTALLATIONS Increase storage capacity by installing two Monogram beverage centers wine chillers or wine reserves together Or for a complete refreshment center install any two of these units together e A side by side installation requires at least a 47 1 2 wide opening No trim kits required e Products must operate from separate properly grounded receptacles PRODUCT CLEARANCES The stainless steel wine chiller wine reserve and beverage center is factory set for a 110 door swing Models that accept custom panels have a 95 door swing When installed in a corner e Allow 4 min clearance on the hinge side for the 90 door swing and to
6. Design Guide with Installation Instructions Wine Chiller Wine Reserve and Beverage Center Monogr fpnorankcon Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully M PO RTANT Save these instructions for local inspector s use M PO RTANT Observe all governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer Note to Consumer Keep these instructions with your Owner s Manual for future reference WAR N N G This appliance must be properly grounded See page 4 AVERTISSEMENT Cet appareil doit tre correctement mis la terre Consultez page 4 If you received a damaged wine chiller wine reserve or beverage center you should immediately contact your dealer or builder Skill Level Installation requires basic mechanical skills Proper installation is the responsibility of the installer Product failure due to improper installation iS not covered under the GE Appliance Warranty CONTENTS Design Guide The Installation Space Product Clearances Side by Side Installation Tools Hardware Step 3 Leveling Step 4 Connect Power Grounding the Product Staining Wood Drawer Fronts Installing the Custom Frame Panel 4 Step 1 Remove Packaging Step 2 Reverse Door Swing WARNINGS e Use this appliance only for its intended purpose e Immediately repair or replace electrical service cord
7. Flatten the shipping carton to use as a pad e Remove the 2 screws and the toekick Set aside the screws and toekick for final installation e Use the supplied Torx bit and electric drill to remove the 3 screws holding the top case hinge Lift off the hinge Screws will be used to install the new hinge e Lift the door off the bottom case hinge e Remove the bottom case hinge pin and bracket Rotate the door The handle will be on the right side of the door hinges will be installed on the left side of the case e Remove the door stop and cam riser on the original bottom right side of the door e Remove the fill plug on the top right side of the door e Turn the door over and reinstall the fill plug on the new left side Reinstall the door e Install the original door stop and cam riser onto the bottom left side of the door e Install the new supplied bottom case hinge pin and bracket onto bottom left side e Place the door onto the bottom case hinge e Install the supplied left hand top case hinge with the 3 original screws e Select the hinge cover marked with an L e Peel backing off the tape inside the decorative hinge COVER Install Covers e Press and snap the hinge cover into place 1 A e Snap the screw hole cover into place on the opposite side IMPORTANT Check to be sure screws are tight and that the door is straight and does not sag The door should swing freely Install 3 Hi
8. O THE CUTOUT e Carefully slide the unit into the opening Be careful not to entangle the power cord e Make certain that the door protrudes 1 beyond the surrounding cabinets 1 7 8 for custom frame models e Check again to be sure the unit is level STEP 6 INSTALL NAMEPLATE e Follow instructions on the back page for installation of the Monogram nameplate STEP 7 SET TEMPERATURE CONTROLS e The temperature controls are preset Refer to the Owner s Manual for more information Allow 24 hours for temperature to stabilize 7 16 deep 1 1 8 wide CUSTOM FRAME PANEL MODELS Model ZDWI240Wil and ZDBI240WIl These models require a custom panel frame surrounding the glass There are two options the panel may be 29 3 4 or 30 high A 30 panel requires a notch cut into the bottom of the panel to avoid interference with the hinges e Rout the back side of the panel to the dimensions shown e A custom handle of your choice or ZTBSS1 Tubular Handle must be installed before the panel is mounted onto the door NOTE The 4 corners of the routed areas must be squared to fit the corners of the metal door frame Option 1 Option 2 2 1 4 wide all sides Rout the back i Rout the 7 i side ofthe back side t 3 4 opening 7 16 of the deep 1 1 8 wide opening 2 1 2 at bottom 3 4 Thick Custom Panel g Back Side 2 1 4 NOTE Right h
9. and models s Cut the notch illustrated Cut notches lt 11 8 deep 1 4 for hinge clearance on the wide and 1 4 opposite side for left hand high door swing Choose Option 1 or Option 2 panel size depending on cabinetry size or style NOTE A solid panel that covers the door glass CANNOT be installed on these models Install the custom panel e Open the door fully e Remove the gasket surrounding the inside of the door to expose the existing screw holes for the custom panel e Hold the custom frame panel against the door and align carefully top to bottom and side to side Mark screw hole locations on the back side of the panel e Drill pilot holes in the back side of the custom panel In hardwood drill 3 32 pilot holes In softwood drill 5 64 holes Secure the prepared panel to the door using ten 10 8 x 5 8 screws Drive the screws through the door frame and into the wood e Replace the gasket 8 x 5 8 ae Screws ZTBSS1 Monogram Tubular Handle Kit BEFORE YOU BEGIN Read these instructions completely and carefully M PO RTANT Save these instructions for local inspector s use M PO RTANT Observe all governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer Note to Consumer Keep these instructions with your Owner s Manual for future reference This kit pro
10. d wood appear darker A true color match can be seen only when the door is opened e Apply the stain and sealer according to the manufacturer s instructions To avoid unpleasant odor keep the door open to ventilate and allow e stain sealer to dry completely before using e product INSTALLING THE CUSTOM FRAME PANEL Go to page 6 for custom frame panel size depending on your cabinet size and style e Install a custom handle of your choice or optional ZTBSS1 Tubular Handle onto the custom panel before the panel is secured to the door e The custom panel should be installed before sliding the product into the installation location STEP 1 REMOVE PACKAGING e Remove corner blocks and foam drawer stops e Remove all packing material tape and protective plastic coverings e Remove stainless steel toekick taped to the back of the unit CAUTI O N Small objects are a choke hazard for children Remove and discard any parts not used MISE EN GARDE Les petits objets peuvent trangler les enfants Il faut jeter toutes les pi ces qui ne sont pas utilis es Installation Instructions STEP 2 REVERSE DOOR SWING SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION Parts Included e Top left case hinge e Bottom left case hinge e Left and right side decorative hinge cover e Decorative hinge screw hole cover e Torx driver bit Tools Required e Phillips screwdriver e Electric drill Remove the door e
11. nge Ff Screws Remove Top Hinge Hinge Apply Monogram Nameplate e Install the Monogram nameplate See instructions and template on back cover Install Toekick The toekick has a cutout on the left and right sides Remove the plug on the left side Move Fill and AS L Plug to reinstall on 4 Right Side the right side If you choose to install the stainless steel toekick reinstall the plug on the right side of that toekick e Install original screws and spacers or screws and spacers supplied with the stainless steel toekick Install screws through the spacer standoff toekick and into the base as shown Installation Instructions STEP 3 LEVEL e Use an adjustable wrench to turn the leveling legs and raise or lower the product e Adjust carefully the product should be level and plumb with cabinetry and should align with adjacent toekick height Turn Right to Lower Turn Left to Raise If you skipped Step 2 e Select the hinge cover marked R or L depending on door swing e Peel backing off the tape inside the decorative hinge cover Press and snap into position e Snap the screw hole cover into place on the opposite side STEP 4 CONNECT POWER e Connect power cord plug to a properly grounded receptacle e Check to make sure power is on by opening the door to see if interior light turns on STEP 5 SLIDE PRODUCT INT
12. s that become frayed or damaged e Unplug the unit before cleaning or making repairs e Repairs should be made by a qualified service technician AVERTISSEMENT ne faut utiliser cet appareil que pour l usage pour lequel il a t construit faut r parer ou remplacer imm diatement tout cordon d alimentation lectrique effiloch ou endommag D brancher le bar ou le r frig rateur a vin avant le nettoyage ou toute intervention Les r parations doivent tre faites par un technicien qualifi For Monogram local service in your area call 1 800 444 1845 For Monogram service in Canada call 1 800 561 3344 For Monogram Parts and Accessories call 1 800 626 2002 www monogram com Installation Instructions Step 5 Slide Product into Cutout Step 6 Install Nameplate Step 7 Set Temperature Controls Custom Frame Panel Models ZTBSS1 Monogram Tubular Handle Kit Template for Nameplate Back Cover Design Guide THE INSTALLATION SPACE Locate Outlet 10 1 2 24 1 8 Framed Models 23 3 4 Stainless Steel Models i 34 1 4 Handle N to 34 3 4 and handle Ls BSS standoff depth PSS is 1 3 4 ec The cutout depth should be 24 The cutout dimensions shown allow for a full door swing and access to the pull out racks when installed as a built in in standard 24 deep cabinets e The wine chiller wine reserve and beverage center can be installed freestanding
13. vides a stainless steel tubular handle to coordinate with other Monogram appliances e The tubular handle must be installed onto the 3 4 thick portion of the custom wood panel before the panel is secured to the door INSTALL THE TUBULAR HANDLE e Use the handle as a template to locate and mark the exact position of the screw holes Be careful to avoid interference with custom panel mounting screws e Draw a pencil line top to bottom and 7 8 from the outside edge e Hold the tubular handle against the appearance side centered on the marked line e Mark the screw hole locations at the center of the handle attachment posts e Center punch the marked hole locations Drill 1 4 pilot holes from the appearance side through the entire panel thickness e Use a 1 2 spade bit to drill 1 4 to 5 16 deep into the back side of the panel Insert washer spacer into the hole e Install screw through the handle standoff and into the pilot hole e Fasten nut onto the screw until the standoff is tight against the panel The screw hole on the standoff should be pointing down toward the floor e Place handle attachment posts inside the standoffs e Use the Allen wrench to install the set screws Tighten handle to standoffs TOOLS AND MATERIALS REQUIRED e Gloves to protect against sharp edges e 2 Phillips screwdriver e Drill and 1 4 bit and 1 2 spade bit e Safety glasses e Center punch e Pencil THIS KIT INCLUDES
Download Pdf Manuals
Related Search