GE JXCHBB User's Manual
Contents
1. JXCHCC JXCHSS Decorative Duct Cover 4 Torx Head Screws Duct Cover With Ceiling Bracket Review the following examples to ensure a trouble free installation using the duct cover accessory 8 ft Ceilings The hood must 8 ft Ceiling be installed at 30 above the cooking surface or 66 above the floor The duct cover will not fit if the hood is installed at a lower or higher height Use the outside 12 section discard the inside section 9 ft Ceiling 24 t 1 1r 1 9 ft Ceilings Install the hood 24 min and up to a maximum of 30 above the cooking surface The duct cover will expand to reach ceiling height 10 ft Ceiling a Ir 1 10 ft Ceilings Install the hood 32 min to 36 max above the cooking surface The duct cover will expand to a maximum of 34 above the top of the hood to meet the ceiling Installation Instructions STEP 1 INSTALL CEILING BRACKET The ceiling bracket must be installed when the duct cover is used to span 24 or more height above the hood The bracket will hold the decorative duct cover in place at the top Note The ceiling bracket is not required when using only the 12 section of the duct cover e Install the 2 small screws into the sides of the duct bracket Remove t2. Installation Instructions JXCHBB Black JXCHWW White JXCHCC Bisque JXCHSS Stainless Steel KIT CONTENTS H 2 Phillips Head E Sa Decorative Screws 2 Wood Screws 2 Washers DUCT COVER REQUIREMENTS These decorative duct covers are designed to conceal the ductwork running from the top of the hood to the ceiling The duct cover can be used to fill a 12 space by using the outer piece alone or using both pieces it will expand from 24 to 34 heights Read this page to be sure the duct cover accessory fits your installation situation Duct Cover Accessory e Use the decorative duct cover to conceal ductwork running from the top of the hood to the ceiling e The duct cover accessory consists of 2 pieces The outside piece is 12 high the inside piece is 22 Nested together they are 24 min expanding to a total maximum height of 34 e The outside piece can be used alone to fill a 12 height e For heights over 12 the ceiling bracket must be installed to secure the cover at the top To avoid unsightly gaps plan the hood installation height for duct cover use e The cover will fit a 12 min height from the top of the hood to the ceiling or 24 min and expanding up to 34 from the top of the hood to the ceiling THE DUCT COVER CANNOT BE USED WHEN THE DISTANCE ABOVE THE TOP OF THE HOOD IS BETWEEN 12 AND 24 2 Wall Fasteners JXCHBB JXCHWW
3. he screws Pre tapping the holes will insure ease of final installation e Match center notch on the bracket to the centerline on the wall and flush against the ceiling e Mark the 2 screw hole locations e Drill 1 8 pilot holes in marked bracket location e If pilot holes do not enter studs enlarge the holes to 3 8 and install wall fastener anchors e Secure the bracket to the rear wall with wood screws and washers Use wall anchors if needed Note Bracket has 2 sets of holes Use larger holes for wall fasteners or wood screws with washers Use smaller holes for wood screws with washers Install Ceiling Bracket When Duct Cover is Used to Span 24 or More See Step 2 to Install Duct Cover STEP 2 INSTALL DUCT COVERS To install the 12 duct cover alone e Place the 12 section of the decorative duct cover on top of the hood e Secure the cover to the top of the hood with 4 screws provided To install the 2 piece duct cover e Place the 2 piece duct cover on top of the hood e Secure the bottom cover to the top of the hood with 4 screws provided e Extend the inside section upwards to meet the ceiling and ceiling bracket e Secure the duct cover to the bracket with the 2 small Phillips screws provided Pub No 49 80107 Dwg No 164D4290P065 N D 245 6 01
Download Pdf Manuals
Related Search