GE JVM2052 User's Manual
Contents
1. Open the door 3 Remove the grille pulling it straight off Charcoal L Us ra I A Filter Install the charcoal filter When properly installed the wire mesh of the filter should be visible from the front 5 Replace the grille and the screws 6 Close the door Insert mesh side up 22 Installation Instructions BEFORE YOU USE YOUR MICROWAVE OVEN Ea Make sure the microwave oven has been 6 Read the Owner s Manual installed according to instructions KEEP INSTALLATION INSTRUCTIONS FOR THE Remove all packing material from the LOCAL INSPECTOR S USE microwave oven INSTRUCTIONS Replace house fuse or turn breaker back on 5 Plug power cord into a dedicated 15 to 20 amp electrical outlet Ensure proper ground exists before use 23 Printed in China2. Recess Self Aligning Screw Microwave Oven Top Attach the microwave oven to the top cabinet Insert 2 self aligning screws through outer top cabinet holes Turn two full turns on each screw Tighten the two screws to the top of the microwave oven While tightening screws hold the microwave oven in place against the wall and the top cabinet Install grease filter See the Owner s Manual packed with the microwave oven Installation Instructions B OUTSIDE BACK EXHAUST Horizontal Duct INSTALLATION OVERVIEW B1 Prepare Rear Wall B2 Attach Mounting Plate to Wall B3 Prepare Top Cabinet B4 Adjust Blower B5 Mount the Microwave Oven PREPARE THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust e Read the instructions on the REAR WALL TEMPLATE e Tape it to the rear wall lining up with the holes previously drilled for holes A and B in the wall plate e Cut the opening following the instructions of the REAR WALL TEMPLATE 15 Installation Instructions ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into
3. bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet A CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts Installation Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws a hole large enough for the power cord to fit through and a cutout large enough for the exhaust adaptor e Read the instructions on the TOP CABINET TEMPLATE e Tape it underneath the top cabinet e Drill the holes following the instructions on the TOP CABINET TEMPLATE A CAUTI O N Wear safety goggles when drilling holes in the cabinet bottom ATTACH EXHAUST DAMPER Blower plate mounting screw 3 screws Blower unit iQ Blower plate Back plate mounting screw 2 screws Place the microwave oven in its upright position with the top of the unit facing up This microwave oven is shipped assembled for top exhaust Attach the exhaust adapter to the blower plate by Sliding it into the guide You will need to make adjustments to ensure proper alignment with your house exhaust duct after the microwave oven is installed MOUNT THE MICROWAVE OVEN injury back inju
4. interferes cabinet with front overhang with the microwave oven installation Remove the decorative trim to install the microwave oven properly Mounting Plate with and to make it level Tabs Below Cabinet THE MICROWAVE OVEN MUST BE LEVEL Bottom the Same Use a level to make sure the cabinet bottom is level Distance as the Front Overhang Depth If the cabinets have a front overhang only with no back or side frame install the mounting plate down the same distance as the front overhang depth This will keep the microwave oven level Measure the inside depth of the front overhang Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang For this type of installation with front overhang only align the mounting tabs with this horizontal line not touching the cabinet bottom as described in Step D T 30 to Cooktop v Installation Instructions D ALIGNING THE WALL PLATE dt L________ Draw a Vertical Line on Wall Hole C Centerline from Center of Notches Top Cabinet oO 00000 0 OWN 000000000 0 oo0oo000 000000409 90000000000 Ga A CAUTION wear gloves to avoid cutting fingers on sharp edges Draw a vertical line on the wall at the center of the 30 wide space A WAR N N G Risk of Electric Shock Can cause injury or death Take care to not drill into electrical wiring inside walls or cabinet
5. or tin snips to cut and remove knockouts from back plate Discard the knockouts Be careful not to distort the plate Knockouts Installation Instructions ADAPT MICROWAVE OVEN BLOWER FOR OUTSIDE BACK EXHAUST cont Carefully pull out the blower unit The wires will extend far enough to allow you to adjust the blower unit BEFORE Fan Blade Openings Facing Up Rotate the unit so that the exhaust ports face the rear of the cabinet When you insert the blower unit the blower wire must be as shown Place the blower unit back into the cabinet Check that the exhaust ports face toward the rear of the cabinet Exhaust ports A WARNINGS risk of electric shock can cause injury or death Do not pull or stretch the blower unit wiring Make sure the wires are not pinched NOTE The blower unit exhaust openings should match exhaust openings on rear of microwave oven 17 Reattach the blower plate to the cabinet so the exhaust ports and blower plate opening are aligned Attach with 2 blower unit mounting screws and then 3 blower plate mounting screws Blower plate mounting screw 3 screws Blower unit 3 AN Blower plate Back plate Blower unit mounting screw Blower unit exhaust ports 2 screws Attach the exhaust adapter to the rear of the oven by sliding it into the guides at the top center of the back of the oven Adapter ocking Tabs
6. transitions wall and roof caps etc present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size When calculating the total duct length add the equivalent lengths of all transitions and adapters plus the length of all straight duct sections The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts NUMBER USED LENGTH Ft Ft Ft Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Installation Instructions DAMAGE SHIPMENT INSTALLATION e If the unit is damaged in shipment return the unit to the store in which it was bought for repair or replacement e If the unit is damaged by the customer repair or replacement is the responsibility of the customer e If the unit is damaged by the installer if other than the customer repair or replacement must be made by arrangement between customer and installer PARTS INCLUDED HARDWARE PACKET Lag Screws 4 x 2 for wall stud holes Toggle Bolts 4 x 3 4 for drywall holes Spring Toggle Heads for toggle bolts Bolts 2 a gt for securing to the upper cabinet Tapping Screws x 2 for attaching the damper duct connector Power Cord Clamp and Dark Colored Mounting Screw to hold th
7. Installation Above the Instructions Cooktop Oven Model JVM2052 BEFORE YOU BEGIN Read these instructions completely and carefully Note to Consumer Keep these instructions gt IMPORTANT sove these pua per i Skill level Installation of this appliance requires basic instructions for local inspector s use mechanical and electrical stalle s IM PORTANT Observe all Proper installation is the responsibility of the installer governing codes and ordinances Product failure due to improper installation is not e Note to Installer Be sure to leave these covered under the Warranty instructions with the Consumer READ CAREFULLY KEEP THESE INSTRUCTIONS MFL57007101 49 40587 1 07 09 JR Installation Instructions CONTENTS General information Important Safety Instructions Electrical Requirements Hood Exhaust Damage Shipment Installation Parts Included Tools You Will Need Mounting Space Step by step installation guide Placement of Mounting Plate Removing the Mounting Plate Finding the Wall Studs Determining Wall Plate Location Aligning the Wall Plate Installation Types A Outside Top Exhaust Attach Mounting Plate to Wall Preparation of Top Cabinet Attach Exhaust Damper Mount the Microwave Oven Outside Back Exhaust Prepare Rear Wall for Outside Back Exhaust Attach Mounting Plate to Wall Preparation of Top Cabinet Adapt Microwave Ove
8. Push in securely until it is in the lower locking tabs Take care to ensure that the damper hinge is installed so that it is at the top and that the damper swings freely Installation Instructions MOUNT THE MICROWAVE OVEN A CAU Tl ON To avoid the risk of personal injury back injury or other injuries due to excessive weight of the microwave oven or property damage you will need two people to install this microwave oven IMPORTANT Do not grip or use handle during installation A WARNING risk of Electric shock Can cause injury or death If installing unit with metal countertops cover the edge of the power supply cord hole with the power supply cord bushing IMPORTANT If filler blocks are not used case damage may occur from overtightening screws NOTE When mounting the microwave oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling Lift microwave oven tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a self aligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later 18 Use the powe
9. ct and masking tape MOUNTING SPACE NOTES Bottom edge of i cabinet needs to The space between the cabinets must be 30 wide ry mS be 30 or more and free of obstructions from the cooking surface e f the space between the cabinets is greater than 30 a Filler Panel Kit may be used to fill in the gap between the oven and the cabinets Your Owner s Manual contains the kit number for your model e This oven is for installation over ranges up to 36 wide 66 or more f r tomthe floot e If you are going to vent your oven to the outside to the top of see Hood Exhaust Section for exhaust duct the oven preparation e e When installing the oven beneath smooth flat cabinets be careful to follow the instructions on the upper cabinet template for power cord clearance e Maximum cabinet depth above and beside the unit is 13 e For models with top venting holes Do not allow cabinetry or other objects to block the airflow of the vent Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATE REMOVING THE MICROWAVE FINDING THE WALL STUDS OVEN FROM THE CARTON REMOVING THE MOUNTING PLATE Remove the installation instructions filters glass tray and the small hardware bag Do not remove the Styrofoam protecting the front of the oven Fold back all 4 carton flaps fully against carton sides Then carefully roll the oven and cart
10. d Ld TTT o MIMI 19 Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet A CAUTI ON Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through P CABINET TEMPLATE e Tape it underneath the top cabinet e Drill the holes following the instructions on the TOP CABINET TEMPLATE A CAU Tl O N Wear safety goggles when drilling holes in the cabinet bottom Installation Instructions ADAPT MICROWAVE OVEN BLOWER FOR RECIRCULATION Remove and save 3 blower plate screws and 2 blower unit mounting screws lt _ Blower plate as mounting screw 3 screws Blower plate Back plate Blower unit ag mounting screw 2 screws Carefully pull out the blower unit The wires will extend far enough to allow you to adjust the blower unit Roll t
11. drywall and reattach the toggle wings to y4 onto each bolt To use toggle bolts Spacing for Toggles More L Than Wall Thickness i Toggle Wings Mounting Toggle Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet A CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts 16 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through e Read the instructions on the TOP CABINET TEMPLATE e Tape it underneath the top cabinet e Drill the holes following the instructions on the TOP CABINET TEMPLATE A CAUTI ON Wear safety goggles when drilling holes in the cabinet bottom ADAPT MICROWAVE OVEN BLOWER FOR OUTSIDE BACK EXHAUST Remove and save 3 blower plate mounting screws and 2 blower unit mounting screws Blower plate mounting screw 3 screws Blower unit Blower plate mounting screw 2 screws Use side cutters
12. e power cord You will find the installation hardware contained in a packet with the unit Check to make sure you have all these parts NOTE Some extra parts are included NOTE You need to install at least two lag screws into a 2 x 4 stud and four anchor bolts into the wall Also the mounting area must meet the 150 lbs weight requirement PARTS INCLUDED ADDITIONAL PARTS Upper Cabinet Fia Template Rear Wall Template 3 pieces mounting plate only Installation 1 INSTALLATION Instructions INSTRUCTIONS Exhaust Adapter eeereeerenrenonnereenronnererneerneerencenerereeceece an aie 1 for the cord hole in a metal upper cabinet Installation Instructions TOOLS YOU WILL NEED J Pe A Ruler or tape measure EEE and straight edge Phillips screwdriver Flat blade screwdriver a Carpenter square optional Oo gt 1 SS AY Se Tin snips for cutting Y damper if required Electric drill with 34 and 34 wood drill bits and 346 and drill bits Filler blocks or scrap f wood pieces if needed Q for top cabinet spacing used on recessed bottom Stud finder or Hammer optional cabinet installations only Scissors to cut template if necessary Saw saber hole or keyhole Clear tape Safety goggles for taping the templates to the wall Du
13. h a properly grounded three prong wall receptacle installed by a qualified electrician A WARNING risk of Electric shock Can cause injury or death DO NOT under any circumstances cut deform or remove any of the prongs from the power cord Do not use with an extension cord Failure to comply may cause fire ELECTRICAL REQUIREMENTS Product rating is 120 volts AC 60 Hertz 14 amps and 1 70 kilowatts This product must be connected to a supply circuit of the proper voltage and frequency Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating The power supply cord and plug should be brought to a separate 15 to 20 ampere branch circuit single grounded outlet The outlet box should be located in the cabinet above the oven The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code A CAU Tl O N For personal safety the mounting surface must be capable of supporting the cabinet load in addition to the added weight of this 63 85 pound product plus additional oven loads of up to 50 pounds or a total weight of 113 135 pounds A CAU Tl O N For personal safety this product cannot be installed in cabinet arrangements such as an island or a peninsula It must be mounted to BOTH a top cabinet AND a wall A CAU Tl ON To avoid the risk of personal injury back i
14. he blower unit 90 so that fan blade openings are facing toward the front of the microwave oven BEFORE Fan Blade Openings Facing Up 20 AFTER Fan Blade Openings Facing Forward NOTE Make sure wires remain routed in the grooves of the motor frame 4 Place the blower unit back into the opening A WARN N G Risk of electric shock can cause injury or death Do not pull or stretch the blower unit wiring Make sure the wires are not pinched Reattach the blower plate to the microwave oven Attach with the 3 blower plate mounting screws and then the 2 blower unit mounting screws lt _ Blower plate rio o o un mounting screw 3 screws ower plate Blower unit Back plate Blower unit ga mounting screw 2 screws Installation Instructions MOUNT THE MICROWAVE OVEN A CAUTION To avoid the risk of personal injury back injury or other injuries due to excessive weight of the microwave oven or property damage you will need two people to install this microwave oven IMPORTANT Do not grip or use handle during installation A WARNING risk of Electric shock Can cause injury or death If installing unit with metal countertops cover the edge of the power supply cord hole with the power supply cord bushing IMPORTANT If filler blocks are not used case damage may occur from overtightening screws NOTE When mounting the microwave oven thread power cord thr
15. n Blower for Outside Back Exhaust Mount the Microwave Oven Recirculating Attach Mounting Plate to Wall Preparation of Top Cabinet Adapt Microwave Oven Blower for Recirculation Mount the Microwave Oven Install the Charcoal Filter Before You Use Your Microwave Oven Installation Instructions IMPORTANT SAFETY INSTRUCTIONS A qualified electrician must perform a ground continuity check on the wall receptacle before beginning the installation to ensure that the outlet box is properly grounded If not properly grounded or if the wall receptacle does not meet electrical requirements noted under ELECTRICAL REQUIREMENTS a qualified electrician should be employed to correct any deficiencies AWARNING Risk of Electric Shock Can cause injury or death Remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury A WARNING risk of Electric shock Can cause injury or death THIS APPLIANCE MUST BE PROPERLY GROUNDED to avoid severe or fatal shock The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Ensure proper ground exists before use Where a standard two prong wall receptacle is encountered it must be replaced wit
16. njury or other injuries due to excessive weight of the microwave oven or property damage you will need two people to install this microwave oven Installation Instructions HOOD EXHAUST NOTE Read these next two pages only if you plan to vent your exhaust to the outside If you plan to recirculate the air back into the room proceed to page 6 OUTSIDE TOP EXHAUST EXAMPLE ONLY The following chart describes an example of one possible ductwork installation EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED LENGTH n 1 12 Ft Straight Duct 6 Round Rectangular to Round Transition Adapter Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Szi mT tS et 7m pe IMPORTANT If a rectangular to round transition adapter is used the bottom corners of the damper will have to be cut to fit using the tin snips in order to allow free movement of the damper OUTSIDE BACK EXHAUST EXAMPLE ONLY The following chart describes an example of one possible ductwork installation ee ee NUMBER EQUIVALENT Pe ne PIECES LENGTH USED LENGTH i 3 Ft Straight Duct 3 x 10 Rectangular Cy O Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Total Length NOTE For back exhaust care should be taken to align exhaust with space between studs or
17. on over onto the top side The oven should be resting in the Styrofoam Carton Find the studs using one of the following methods A Stud finder a magnetic device which locates nails OR B Use a hammer to tap lightly across the mounting surface to find a solid sound This will indicate a stud location After locating the stud s find the center by probing the wall with a small nail to find the edges of the stud Then place a mark halfway between the edges The center of any adjacent studs should be 16 or 24 from this mark Mounting Draw a line down the center of the studs pales Plate IMPORTANT The microwave oven must be connected i to at least one wall stud Pull the carton up and off the oven Remove and properly discard plastic bags Remove the 2 screws from the mounting plate This plate will be used as the rear wall template and for mounting You may discard these screws Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position beneath flat bottom Plate position beneath framed recessed cabinet cabinet bottom Mounting Plate Tabs Touching the Cabinet Bottom Mounting Plate Tabs Touching the Back Frame 1 Ia 30 to Cooktop At least 30 up to 36 l Plate position beneath recessed bottom Your cabinets may have decorative trim that
18. ough hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling Lift microwave oven tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a self aligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later 21 Use the power supply cord clamp to bundle the power supply cord Install the power supply cord clamp using a screw as shown to the inside of the cabinet Cabinet Front SJ Cabinet Bottom Shelf wa Filler Block Equivalent to Depth of Cabinet Recess UU Self Aligning Screw Microwave Oven Top Attach the microwave oven to the top cabinet Insert 2 self aligning screws through outer top cabinet holes Turn two full turns on each screw Tighten the two screws to the top of the microwave oven While tightening screws hold the microwave oven in place against the wall and the top cabinet Install grease filter See the Owner s Manual packed with the microwave oven Installation Instructions INSTALLING THE CHARCOAL FILTER Remove 2 screws on the top front of the grille using a Phillips screwdriver 2
19. r supply cord clamp to bundle the power supply cord Install the power supply cord clamp using a screw as shown to the inside of the cabinet Cabinet Front SJ Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self Aligning Screw Microwave Oven Top Attach the microwave oven to the top cabinet Insert 2 self aligning screws through outer top cabinet holes Turn two full turns on each screw Tighten the two screws to the top of the microwave oven While tightening screws hold the microwave oven in place against the wall and the top cabinet Install grease filter See the Owner s Manual packed with the microwave oven Installation Instructions RECIRCULATING inon vented Ductless INSTALLATION OVERVIEW C1 Attach Mounting Plate to Wall C2 Prepare Top Cabinet C3 Adjust Blower C4 Mount the Microwave Oven C5 Install Charcoal Filter ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to onto each bolt To use toggle bolts Spacing for Toggles More Than Wall gt lt Thickness i Toggle Wings Mounting Toggle Bolt En
20. ry or other injuries due to excessive weight of the microwave oven or property damage you will need two people to install this microwave oven IMPORTANT Do not grip or use handle during installation A WARNING risk of Electric shock Can cause injury or death If installing unit with metal countertops cover the edge of the power supply cord hole with the power supply cord bushing IMPORTANT If filler blocks are not used case damage may occur from overtightening screws NOTE When mounting the microwave oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord Lift microwave oven tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a self aligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Installation Instructions MOUNT THE MICROWAVE OVEN cont Use the power supply cord clamp to bundle the power supply cord Install the power supply cord clamp using a screw as shown to the inside of the cabinet Cabinet Front A Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet
21. s Use the mounting plate as the template for the rear wall Place the mounting plate on the wall making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cabinets 4 Drill holes on the circles If there is a stud drill a 16 hole with front overhang Line up the notch and centerline A ce ie a Va don t line up with a stud on the bottom of the mounting plate to the centerline Pe POE OTTO DONS on the wall NOTE DO NOT mount the plate at this time 3 While holding the mounting plate with one hand draw circles on the wall at holes A B C and D see illustration above actual plate marked with arrows Four holes must be used for mounting NOTE Holes C and D are inside area E If neither C nor D is in a stud find a stud somewhere in area E and draw a fifth circle to line up with the stud It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave oven Set the mounting plate aside 10 Installation Instructions INSTALLATION TYPES choose A B or C This microwave oven is designed for adaptation NOTE This microwave oven is shipped assembled for Outside to the following three types of ventilation Top Exhaust except for non vented models Select the type A Outside Top Exhaust Vertical Duct of ventilation required for your installation and proceed to B Outside Back Exhaust Horizontal Duct tha
22. t section C Recirculating Non Vented Ductless OUTSIDE TOP EXHAUST B OUTSIDE BACK EXHAUST VERTICAL DUCT HORIZONTAL DUCT Adaptor in Place for Outside Top Exhaust See page 12 See page 15 RECIRCULATING NON VENTED DUCTLESS A Charcoal Filter Accessory Kit is required for the non vented exhaust See your Owner s Manual for the kit number See page 19 11 Installation Instructions A OUTSIDE TOP EXHAUST vertical Ducti INSTALLATION OVERVIEW A1 Attach Mounting Plate to Wall A2 Prepare Top Cabinet A3 Attach Exhaust Damper A4 Mount Microwave Oven ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 7 onto each bolt To use toggle bolts Spacing for Toggles More Than Wall gt lt Thickness Toggle Wings Mounting mT Toggle Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle
23. wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust Installation Instructions NOTE If you need to install ducts note that the total duct length of 3 4 x 10 rectangular or 6 diameter round duct should not exceed 120 equivalent feet Outside ventilation requires a HOOD EXHAUST DUCT Read the following carefully NOTE It is important that venting be installed using the most direct route and with as few elbows as possible This ensures clear venting of exhaust and helps prevent blockages Also make sure dampers swing freely and nothing is blocking the ducts Exhaust connection The hood exhaust has been designed to mate with a standard 3 x 10 rectangular duct If a round duct is required a rectangular to round transition Adapter must be used Do not use less than a 6 diameter duct DUCT PIECES LENGTH Rectangular to Round Transition Adapter Wall Cap 90 Elbow 90 Elbow 45 Elbow Roof Cap Straight Duct 6 Round or 31 4 x 10 Rectangular IMPORTANT If a rectangular to round transition Adapter is used the bottom corners of the damper will have to be cut to fit using the tin snips in order to allow free movement of the damper a EQUIVALENT Maximum duct length For satisfactory air movement the total duct length of 3Y x 10 rectangular or 6 diameter round duct should not exceed 120 equivalent feet Elbows
Download Pdf Manuals
Related Search