Humminbird Wide 100 Fish Finder User Manual
Contents
1. Thru Hull Mounting Thru hull transducers install through a hole drilled in the hull of the boat Larger boats or boats with inboard motors create 7 X turbulence that make transom mounting ineffective Also hulls that are very thick or are double layered or made from materials such as wood or metal which do not conduct sonar signals make inside the hull mounting inadvisable Thru hull mounting may require the use of a fairing block to level the transducer with the waterline Also since special tools and knowledge may be required to perform this type of installation it is best to refer to a qualified marine technician INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replacements for the standard transducer You may exchange your new and unassembled transducer for another type by returning it to the address listed in Customer Support Some transducers may have additional cost Refer to the Accessory catalog or call Customer Support for information BEGINNING INSTALLATION Now that you have determined the transducer mounting method you can begin installation of your new Humminbird fishfinder The installation guide included on the next few pages provides detailed step by step instructions for installation of the control head and transducer For transom mount transducer installations you will need the mounting template included with your manual In addition to the parts inc2. almost anywhere on the boat The transducer converts electrical energy from the transmitter into mechanical pulses or sound waves The transducer also receives the reflected sound waves and converts them back into electrical signals for display on the control head It should be installed in contact with the surface of the water in an area that has smooth waterflow usually on the transom of the boat There are several mounting options for the transducer Review the following section to determine the method that works for you and your boat INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminbird fishfinder includes a standard transducer This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat The transom installation which is the most widely used places the transducer on the outside of the boat hull This technique produces the least signal loss and provides a way to adjust the transducer after installation The mounting hardware included is designed to protect both the boat and the transducer should the boat strike debris in the water or when trailering Transom Mounted Transducer As an alternative to transom mounting it is possible on many fiberglass hulled boats to glue the transducer on the inside of the boat hull Since fiberglass has similar sonar characteristics as water the sonar signal can pass through the boat hull with
3. and the unit will automatically locate the bottom adjust the depth range and sensitivity to an appropriate level and draw a picture of the terrain beneath your boat If POWER is the only button you press you will benefit from the advanced automatic bottom tracking capability of the unit However if you choose to experiment with the many features and controls the Wide One Hundred offers you can customize the presentation of information to suit your particular needs The Wide One Hundred offers a wide variety of settings and types of display to satisfy any sonar need SIMULATOR OPERATION The Wide One Hundred contains a simulator which allows you to use the unit as if you are on the water This simulator is invaluable for learning how to operate the many features of the Wide One Hundred With the unit turned off press and hold the POWER button until a continuous chirp is heard This initiates the simulator operation and the unit will simulate all functions as if it were actually on the water When in simulator operation the Wide One Hundred unit responds to control inputs as if it is in actual operation so feel free to experiment with the many features and functions to customize the Wide One Hundred unit for your particular operation To exit the simulator press POWER to turn the unit off WHAT YOU SEE ON SCREEN The first thing you may notice about the Wide One Hundred is the high resolution super highvisibility LCD screen This LCD
4. immediate area of the propeller s Figure 1 On outboard or inboard outboard boats it is best to stay at least 15 40cm to the side of the propeller s If possible viewing the transom of the boat while the boat is moving will provide the best means of locating turbulence free water If maximum high speed operation is a high priority this is the recommended method If this is not possible select a location on the transom where the hull forward of this location is smooth flat and free of protrusions or ribs The transducer when mounted should point straight down The design of the transducer will accommodate a wide range of deadrises and remain ported straight down Figure 2 Transom Mounting Location Stepped Hull On boats with stepped hulls it may be possible to mount the transducer on the step Never mount the transducer on the transom behind a step as this area of the transom will not be in contact with the water at high speed Figure 3 INSTALLATION TRANSOM INSTALLATION If the propeller s is are forward of the transom it may be impossible to find an area clear from turbulence and a different mounting technique or transducer type should be considered Step Two Drill the Mounting Holes 1 2 Step Three Assemble the Transducer Remove the mounting template from the front of the Operations Manual Hold the template on the transom of the boat in the location where the transducer will be ins
5. install the transducer Consider the following to find the best location e Observe the outside of the boat hull to find the areas that are mostly free from turbulent water Avoid ribs strakes and other protrusions as these create turbulence Figure 14 e Asageneral rule the faster the boat can travel the further aft and closer to the centerline of the hull the transducer has to be located to remain in contact with the water at high speeds Step Two Test the Mounting Location There is no opportunity for adjustment after the transducer glued Transducer Mounted Inside the Hull Preferred Mounting Area in place Therefore it is best to perform a trial installation on inside the hull transducers first and run the boat at high speeds to determine the best mounting area 1 Atthe identified mounting location lay the transducer body face down with the pointed end towards the bow 2 Fill the hull with enough water to submerge the transducer body Use a sand filled bag or other heavy object to hold the transducer in position The transducer cannot transmit through air The water purges any air from between the transducer and the hull and fills any voids in the coarse fiberglass surface 3 INSTALLATION INSIDE THE HULL INSTALLATION Power up the Control Head 4 Run the boat at various speeds and water depths while observing the screen on the Control Head If the unit functions well at low speeds but begins to
6. is displayed If the boat is in water sonar data appears If the bottom is visible on screen with a digital depth readout the unit is working properly Ensure the boat is in water greater than 2 but less than the depth capability of the unit and the transducer is fully submerged Remember the sonar signal cannot pass through air If the unit is working properly gradually increase the boat speed to test high speed performance If the unit functions well at low speeds but begins to skip or miss the bottom at higher speeds the transducer requires adjustment Refer to the appropriate transducer installation section for more detail Note it is often necessary to make several incremental transducer adjustments before optimum high speed performance is achieved Important For Transom Mount transducer installations install the third mounting screw after the final transducer adjustments Humminbird e 3 Humminbird Lane e Eufaula Alabama 36027 TESTING THE INSTALLATION After installation is complete and all connections are made you are ready to test the installation prior to actual use Thorough testing should be performed with the boat in water however you can initially confirm basic operation with the boat trailered Press POWER once to turn the unit on There will be an audible chirp when any button is pressed that confirms the button press If the unit does not power up ensure that the unit is fully seated on the mount and that pow
7. minimal loss The hull of the boat must be single layer construction not double hulled Also any air trapped in the lamination of the fiberglass would prevent the sonar signal from passing through Inside the Hull Mounted Transducer Inside the hull installations require no holes be drilled into the boat and through experimentation high speed operation comparable to transom mounting can be achieved Two part slow cure epoxy not included is required to glue the transducer in place INSTALLATION PREPARATION ALTERNATE MOUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything necessary for installation and operation on most boats However there are several situations which may require a different type of transducer Inboard boats wood or metal hulls and sail boats create unique transducer mounting needs Alternate transducers and mounting methods are detailed below Portable Mounting The standard transducer can be adapted for portable installations with a portable mounting kit available from Humminbird This accessory adapts your transducer to a suction cup mount for temporary installation on the boat hull or other surface Trolling Motor Mounting The standard transducer can also be adapted to mount on most trolling motors using a different accessory kit This accessory includes a bracket and hose clamp that allows mounting the transducer to the body of most trolling motors
8. the depth of the zoom range first using the UP and DOWN Arrow buttons until the upper and lower limit numbers correspond with the range you wish to view then enable Zoom using the ENTER button Aq q oromoo eee Once you are in Zoom you may still adjust the depth of the zoom range by using the UP and DOWN Arrow buttons The Zoom menu will not appear when an adjustment is made unless MENU is pressed The digital depth readout will continue to track the bottom even E when Zoom is enabled EIE GIT War Bottom Lock is a function of Zoom except the depth adjustment is controlled automatically to view the area immediately above the bottom This is especially useful if you are looking for structure or minor variations in terrain in areas of relatively flat bottom terrain To enable Bottom Lock press ENTER until the BL is highlighted The Zoom range will be controlled by the current depth range as in Zoom and will be indicated on the Zoom menu Bottom Lock Indicator Bottom Alarm The Wide One Hundred contains an audible alarm to warn you of shallow water depths This alarm is adjustable from 2 to 99 of depth To enable the alarm simply adjust the alarm depth using the UP and DOWN arrow buttons and press ENTER Whenever the depth of the water beneath your boat is equal to or less than the selected alarm depth a continuous alarm will sound To disable the alarm either move to deeper water or select the Bottom Alarm menu and
9. 1 2 3 Apply silicone sealant to the mounting holes drilled into the transom Align the transducer assembly with the drilled holes in the transom Figure 8 Use either a flat head screwdriver a 5 16 8mm hex driver or a 5 16 8mm socket to mount the assembly Using the two 10 1 4 25mm long slotted hex head screws mount the transducer assembly to the transom as shown Do not fully tighten the Py mounting screws in order to vertically adjust the transducer may Snap the pivot down into place pa c ies ma Step Five Adjust the Running Position of the Transducer The bracket allows height and tilt adjustment the pivot screws allow angular adjustment Initially adjust the transducer as described in the following paragraphs Further adjustment may be necessary to refine the instillation after high speed testing 1 Adjust the height of the assembly so the face of the Running Position First adjust the pivot angle of the transducer body so its Adjustment length is parallel with the length of hull of the boat Then 7 pivot the transducer down so the rear is about 1 4 inch 6mm lower than the front Figure 9 I i Fully tighten the two pivot screws using the Allen wrenches b 77 It may be necessary to retighten the pivot screws after the initial use as the plastics may still be seating to the lock washers transducer is 3 16 4 5mm beneath the lower edge of the transom Figure 10 Mar
10. WITT Ouehuudred Operations Manual Ph corde open INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fishfinder please ensure the following parts are included in the box Fishfinder Transducer with 20 6m of cable and mounting hardware kit Mounting system and mounting hardware kit 6 2m power cable Publications kit It any of these items is missing call our Customer Support Hotline ACCESSORIES Humminbird offers a wide assortment of accessories that complement and expand the capability of your new fishfinder These accessories are designed with the same high standards and are backed by the same one year warranty The Humminbird Accessory catalog included with your unit contains descriptions of the many accessories available and ordering information All Humminbird accessories are available through your full service Humminbird dealer or factory direct through our number listed in the Customer Support section INSTALLATION OVERVIEW Your Humminbird fishfinder consists of two primary components to install the control head and the transducer The control head contains the sonar transmit and receive circuitry as well as the user controls and display It should be installed in a location that provides access to the controls and visibility while in use The control head mounts on a quick disconnect mounting system that swivels and tilts providing flexibility for viewing from
11. able through the hole 2 Fill the hole with silicone sealant 3 Place the escutcheon plate over the hole and attach with the two 8 x 5 8 16mm screws 4 Secure the cable by attaching the cable camp to the transom using a 8 x 5 8 16mm screw Note The transducer will pivot up to 90 degrees in the bracket Allow enough slack in the cable for this movement It is best to route the cable to the side of the transducer so the cable will not be damaged by the transducer during movement INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be installed and operational See Installing the Control Head for instruction on installing the unit Inside the hull mounting generally produces good results in single thickness fiberglass hulled boats Humminbird cannot guarantee depth performance when transmitting and receiving through the hull of the boat since some signal loss occurs The amount of loss depends on hull construction and thickness and the installation This installation requires slow cure two part epoxy Do not use silicone or any other soft adhesive to install the transducer as this material reduces the sensitivity of the unit Five minute epoxy has a tendency to cure before all the air bubbles can be purged Step One Determine the Mounting Location Begin the transducer installation by determining where inside the hull to
12. depth range selected is controlled by the UP and DOWN arrow buttons The depth ranges are 015 30 60 120 180 240 360 480 amp 600 een ol Auto Range indicator If you alter the depth range Manual operation is automatically selected and the area beneath the bottom will no longer be blackened in ais como he a han Shan 129 Manual Ranai This feature is valuable if you are only interested in targets near the surface The Wide One Hundred will always display the digital depth of the water regardless of whether the bottom is shown on the selected depth range Zoom Another form of range control is Zoom The Zoom menu allows three different settings Zoom Off Zoom On and BL or Bottom Lock Zoom allows selection of various ranges for full screen viewing not necessarily including the surface By using the display to view a smaller area the effective display resolution is increased and the units ability to separate targets close together is enhanced 31 f EE ALI 49 a GI 349 Zoom Indicator The zoom range is determined by the depth range in use when zoom is enabled In shallow water when the 15 or 30 depth range is used the zoom range will be 7 1 2 If the 60 or 120 depth range is in use the zoom range will be 15 if a 180 to 480 depth range is used the zoom range will be 30 and if the 600 range is in use the zoom range will be 60 To enable zoom adjust
13. display uses super twist technology and is ruggedized for tough shock and vibration endurance The display is also backlit for nighttime operation and uses special components so it can operate at temperatures more extreme than you are likely to encounter The horizontal line at the top of the display is the Zero line This represents the surface of the water The Zero line will always have a gap which moves as the screen updates This gap lets you know that the display is updating even if the bottom terrain remains the same or is not visible on the selected depth range The farthest right column of information is the most recent information and it shows what is directly under your boat At power up the Wide One Hundred locates the bottom and adjusts the depth range to a setting most appropriate for that depth The bottom will be usually shown about 2 3 of the way down the display Upper Range Limit 2 a Zero Line Fish Symbols ID Fish Depth 24 Sensitivity a Bottom Setting Terrain Lower Range Limit Range Setting Fish Alarm Indicator Depth Since some species of fish tend to be better reflector of sonar than others the strength of return is not always an accurate indicator of fish size however typically the larger the fish the larger the signal return CONTROL FUNCTIONS The Wide One Hundred unit uses only seven buttons to control all functions The controls are divided into two groups POWER STOP and LIGHT are one gro
14. er is available Momentarily information will begin to march across the screen from right to left Remember that as each column advances on the screen it contains information gathered from several transmit and receive cycles The column of information on the far right side of the screen is the most current information or the view directly under your boat If your boat is moving an accurate depiction of the terrain you have just covered is created on screen If the bottom is visible on screen with a digital depth readout the unit is working properly If the unit powersup but fails to display bottom information the transducer is not properly connected Ensure that the boat is in water greater than 2 but less than 600 deep and that the transducer is fully submerged Remember that the sonar signal cannot pass through air Refer to the troubleshooting section of this manual If the unit is working properly gradually increase the boat speed to test high speed performance If the unit functions well at low speeds but begins to skip or miss the bottom at higher speeds the transducer installation requires adjustment Refer to the appropriate transducer installation section for more detail NOTE It is often necessary to make several incremental transducer adjustments before optimum high speed performance is achieved HHUMMINBIRG USING THE WIDE ONE HUNDRED The Wide One Hundred is simple to use Simply press the POWER button
15. k the position of the mounting bracket on the transom with a pencil Force the pivot to the up position to gain access to the mounting screws Assure the transducer location has not gt changed then fully tighten the two mounting screws Figure 11 Snap the pivot back down L Rad Confirm the pivot angle has not changed a Sh Note A third screw location is provided for the mounting bracket Drill this hole and install the screw after final testing and adjustments have been completed INSTALLATION TRANSOM INSTALLATION Step Six Route the Cable There are several ways to route the transducer cable to the to the area where the control head will be installed The most common procedure routes the cable through the transom into the boat Inside the boat there is often a channel or conduit used for other wiring that the cable can be routed along Do not cut or shorten the transducer cable and try not to damage the cable insulation Route the Cable Route the cable as far as practical from the VHF radio antenna cables or tachometer cable to reduce the possibility of l Ak interference gt cd If the cable is too short extension cables are available to extend Y the transducer cable up to a total of 50 15 m Call Humminbird Lu Customer Support for more information asi A Follow these steps to route the cable through the transom D 4 1 Drill a 5 8 16mm hole above the water line Route the c
16. luded you need the following for installation and operation A powered hand drill and various drill bits Philips and flathead screwdrivers A ruler or measuring tape Pen or pencil 12 volt power source your boat s battery A 1 amp fuse A fuse holder if you are wiring directly to the boat s battery Silicone sealant for sealing drilled holes 2 part slow cure epoxy for inside the hull transducer installations INSTALLATION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide This chapter contains information critical to the correct installation of your transducer Due to the wide variety of boat hulls only general instructions are presented in the installation guide Each boat hull represents a unique set of requirements that should be evaluated prior to installation TRANSOM INSTALLATION Step One Determine Where to Mount the Transducer Begin the transducer installation by determining where on the transom to install the transducer Consider the following to find the best location It is very important to locate the transducer in an area which is relatively free of turbulent water As a boat moves through the water turbulence is generated by the weight of the boat and the thrust of the propeller s This turbulent water is normally confined to areas immediately aft of ribs strakes or rows of rivets on the bottom of the boat and in the
17. m Ve underneath Also you must break out the tabs on the gt a rear of the mounting base using needle nose pliers Figures 24 25 2 Insert all cables through the 1 25mm hole from beneath the mounting surface EA S 3 Pass the cables through the grommet if the cable hole is A A underneath the mounting bracket then press the grommet Q amp in place around the cables and into the 1 25mm hole 4 Pass the cables through the mounting base out the top of the mounting bracket 5 Place the mounting bracket on the mounting surface aligned with the drilled holes Insert the four flathead wood screws into the mounting holes and tighten fully Figure 23 Optional If the cables pass outside the mounting bracket install the hole cover over the hole and fasten in place using the two 8 x 7 8 22mm wood screws Figure 24 INSTALLATION CONTROL HEAD INSTALLATION Step Five Assembling the Connector Holder 1 Insert the cable connectors into the connector holder The cable connectors are labeled and there are corresponding labels on the connector holder Figure 26 The slots for the connectors are keyed to prevent reverse installation so do not force the connector into the holder Carefully pull the excess cable from beneath the mounting surface so the connector holder aligns with the mounting holes on the front of the mounting bracket Figure 27 Snap the support plate to the rear of the connect
18. or holder Figure 28 Insert the connector holder into place and use the two 6 32 x 3 4 9mm screws to fasten it to the mounting bracket Figure 28 Install the control head by sliding it onto the mounting bracket until it is fully seated To remove the unit simply depress the latch on the rear of the unit and lift Figure 29 Your Humminbird is now ready for operation Connector Holder INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water however you can initially confirm basic operation with the boat trailered Press POWER once to turn the unit on There will be an audible chirp when any button is pressed to confirm the button press If the unit does not power up ensure the unit is fully seated on the mount and that power is available The first screen provides four options Start up Options Simulator and Diagnostic A message at the bottom of the screen indicates the transducer connection If no transducer is detected or one is not connected the message will indicate this and the unit will go into simulator after the initial screen times out Note the transducer must be submerged in water for reliable transducer detection If a transducer is detected the unit will enter Start Up or normal operation unless you choose another option If you do not press any button before the timer reaches 0 the normal operation screen
19. places a fuse panel usually located near the console or directly to the battery If a fuse terminal is available use crimp on type electrical connectors not included that match the terminal on the fuse panel Attach the black wire to ground and the red wire to 12 VDC power Figure 20 Be sure to use a one amp fuse in the connection If you must wire the control head directly to a battery be sure to install an inline fuse holder INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse not included for the protection of the unit Figure 21 Humminbird is not responsible for over voltage or over current failures In order to minimize the potential for interference with other 1 25n marine electronics a separate power source such as a second battery may be necessary ie Step Three Drill the Mounting Holes 1 Set the mounting bracket in place on the mounting surface Mark the four mounting screw locations with a pencil or punch _ 2 2 Set the mounting bracket aside and drill the four lr M Bra mounting screw holes using a 9 64 3 6mm bit fa JAJ YA Step Four Run the Cables A lt L gt 1 Ifthe cables must pass through a hole underneath the N mounting surface mark and drill a 1 25mm hole ee centered between the four mounting holes Figure 22 Note if the cables must pass through the mounting surface at a different location drill the 1 25mm hole at that location and pass the cables through fro
20. press ENTER to turn the alarm off Fish Alarm The Fish Alarm alerts you to the presence of fish or other targets not attached to the bottom in the water beneath your boat The Fish Alarm has 3 different settings which correspond to the 3 different size fish targets shown on screen To enable Fish Alarm use the UP and DOWN arrow buttons to adjust the size return you want to be alerted to large fish only large and medium size fish or all fish Then press ENTER to s enable the alarm When Fish Alarm is on an onscreen indicator will be shown Remember that it is impossible for sonar to determine if a signal return is a fish or some other type of object or suspended debris Any object not connected to the bottom is normally a fish and is portrayed as a fish symbol The strength of the Fish Alarm Indicator reflected sonar signal from a target is a good indicator of the size of the target and the fish symbol displayed represents the strength of the signal reflected from it a 189 ID ID is the automatic identification of target returns based on the strength of the returned signal and other factors Three options are available ID On displays targets as one of three different size fish symbols fib ence 1 e 1673 lt 3 H 240 Sen POR Fe GIGI 188 Ea GI 188 ID Fish Symbols Raw Sonar Information ID Fish Depth ID the default setting provides more information about the location of the
21. re to mount the control head Consider the following to determine best location e The cables for power transducer and temp speed accessories if applicable should be installed first and must reach the mounting location Extension cables are available e There are two ways to route the cables to the unit through a hole in the mounting surface underneath the mounting bracket or from a hole outside the mounting bracket Routing the cables down under the mount provides maximum weather protection however this is not always feasible if the area under the L fishfinder is inaccessible In this case route the cables through a hole at another location and cover with the supplied hole cover e The mounting surface should be adequately supported to protect the fishfinder from excessive wave shock and vibration Ww and provide visibility while in operation f e The mounting area should allow sufficient room for the unit to J pivot and swivel freely and for easy removal and installation lt Figures 18 19 d oot Step Two Connect the Power Cable to the Boat Ty VL _ BF A 2m long power cable is included to supply power to the gt Peu fishfinder You may shorten or lengthen the cable using 18 gauge Ks multi stranded copper wire a CAUTION Some boats have 24 or 36 volt electric systems Be sure your unit is connected to a 12 VDC power supply raz The Power can be connected to the boat s electrical system at two
22. receiver is adjusted automatically based on a number of factors such as the depth of the water and the signal clarity In murky water full of debris the Wide One Hundred will select a lower sensitivity setting In clear water where there is little debris to defract the sonar signal the sensitivity is set higher The Sensitivity menu allows you to bias this automatic setting up or down based on personal preference You can select a bias of 5 to 5 for 11 different bias settings A bias setting of 0 has no effect on the automatic function A 3 setting selects a sensitivity setting three steps higher than the unit would normally select so even the smallest returns are displayed onscreen Sensitivity A setting of 2 sets the sensitivity two steps below what the unit Setting would normally select so only the largest targets or other Indicator returns are displayed The Wide One Hundred adjusts the depth range automatically so the bottom return is displayed at the bottom 1 3 of the display This leaves the top 2 3 to display anything between the surface and the bottom As your boat moves over deeper or shallower water the unit adjusts the depth range of the display to keep the bottom return in the same general area on the screen You may however choose to control this range adjustment manually By pressing ENTER you can select manual operation meaning the unit will no longer adjust the depth range automatically The
23. rolled functions MENU brings a menu on screen for adjustment or if a menu is already present the next menu in sequence will appear Menus will go off screen and normal operation will resume after a short period of time If you wish to keep the menu onscreen for an extended period of time press STOP UP ARROW selects the next larger or next sequential adjustment within the menu Holding an Arrow button down will cause the unit to continue to make the adjustment until a limit is reached and a continuous chirp is heard DOWN ARROW selects the next smaller adjustment within the menu ENTER is used to toggle other menu options on and oft All menus use the same general layout as shown in in the sample menu below The heading of the menu is at the top The area in the center is controlled by the UP and DOWN ARROWS and the area under the horizontal line is controlled by the ENTER button Not all menus are affected by all controls but the layout is the same regardless Pressing MENU repeatedly will sequentially display all available menus Menu Functions The following section explains each menu in detail and how these adjustments can be used to extract the maximum information from the sonar returns Remember once a setting has been changed the Wide One Hundred will remember that setting until it is changed again or until the unit is powered off Sensitivity www As the Wide One Hundred receives returned signals the sensitivity of the
24. skip or miss the bottom at higher speeds the transducer needs to be moved If depth performance is required test the fishfinder in water at the desired depth Test different locations in the hull until the optimum performance is achieved Step Three Permanently Mount the Transducer 1 Once the mounting location is determined mark the position of the transducer Remove the water from inside the hull and thoroughly dry the mounting surface If the surface is excessively rough it may be necessary to sand the area to provide a smooth mounting surface Ensure the mounting area is clear and dry Mix an ample quantity of two part slow cure epoxy slowly and thoroughly Avoid trapping air bubbles Coat the face of the transducer and the inside of the hull Figure 16 Press the transducer into place with a slight twisting motion to purge any trapped air from underneath keeping the pointed end of the transducer body pointed forward Figure 17 Note Proper operation requires the pointed end of the transducer body to face towards the bow 6 Weight the transducer so it does not move while the epoxy is curing When the epoxy cures no water is necessary inside the hull Neither water spilled gasoline or oil will affect the performance of the transducer INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One Determine Where to Mount Begin the installation by determining whe
25. talled Figure 4 Align the template vertically ensuring the lower edge of the transom meets with the bottom corner of the template Template alignment Using a pencil or punch mark the two mounting holes shown on the template onto the transom Do not mark or drill any other holes at this time Using a 5 32 4mm bit drill the two holes to a depth of approximately 1 3cm On fiberglass hulls it is best to start with a smaller bit and use progressively larger drill bits to reduce the chance of chipping or flaking the outer coati ng Transducer Assembly air he gt 4 lt 3 1 Attach the Pivot to the transducer body as shown in Figure owe 5 using the 8 3 8 9mm long allen headed pivot screw GOR the headed pin the two flat washers and the two toothed Pivot Screw gt lock washers 176 cd tae le Note The toothed lock washers must be positioned i between the transducer and the pivot ears The flat om washers must be positioned to the outside at the pivot Y ears U A z ap E 2 Using the Allen wrenches provided loosely tighten the pivot a screw Figure 6 Do not completely tighten the assembly at L this time so the pivot angle can be adjusted later 3 Insert the pivot transducer assembly into the mounting bracket as shown in Figure 7 Do not snap the assembly closed esa INSTALLATION TRANSOM INSTALLATION Step Four Mount the Transducer to the Transom
26. target by attaching depth strings showing the digital depth of the target When there are numerous targets on screen not every target depth is shown to avoid excessive clutter on screen ID OFF disables the units interpretation of targets and displays the raw sonar information as it is received Advanced users may prefer this type of presentation so they can make there own interpretation from the information displayed Scroll Scroll Rate controls the update rate of the display There are five rate settings available You may speed up or slow down the rate to match your personal preference To present the most accurate representation of the terrain beneath your boat the scroll rate of the display should be approximately synchronized to the speed of the boat If your boat is stationary or moving slowly select a slower scroll rate and if you typically operate the boat at high speeds use a faster scroll rate
27. up y and the Menu System controls are the other group When any button is pressed an audible chirp will verify the control input POWER as previously discussed powers the Wide One Hundred for normal operation Also if the unit is powered off press and hold POWER until you hear a continuous chirp to enable simulator operation as discussed in Simulator Operation Pressing 4 POWER when the unit is in normal or simulator operation will power the unit off STOP freezes the display to allow closer study Pressing STOP again will resume normal operation Also if a menu is on screen STOP will retain the menu on screen until STOP is pressed again The transmitted sonar signal travels downward and is reflected back toward the surface by the bottom or other objects for display on screen If a target is detected between the surface and the bottom it is displayed as a fish symbol Depending on the strength of the signal reflected from the object one of three different size symbols is used These reflected signals are normalized for depth so that a small fish does not appear to be a large fish if it is close to the boat LIGHT enables a two level display backlight Pressing once will turn the light on low pressing a second time will increase the backlight to the high setting and pressing a third time will turn the backlight oft The four remaining buttons work together to control the Menu System an array of menu cont
Download Pdf Manuals
Related Search