GE EL Series Installation Guide
Contents
1. Electrical Connections 1 See previous steps 1 and 2 Carefully place enclosure cover next to electrical enclosure Follow the wiring diagram insert stripped wires into Lutron interface connector as described in next step c Green yellow d White a ERAN e Orange 9 b Violet Black D ae A y ee et ZA 3 Connect Driver wires to Lutron interface as follows a Driver 0 10V grey wire to Lutron grey connector b Driver 0 10V violet wire to Lutron violet connector c One green yellow wire to Lutron green connector d One Driver white wire to Lutron white connector e Driver orange wire to Lutron orange connector EcoSystem line Push out appropriate size knockout tabs and install approved conduit connectors for both the AC and EcoSystem lines O Connect AC line to black white and green wires from Lutron interface with twist on wire caps Connect EcoSystem bus wires to the two purple Lutron connectors Link E1 and E2 Next connect the luminaire wires to the blue and red wires of the power supply Connect the green wires to the ground screw QO After completing connections replace enclosure cover and screw down M4 screws and lock washers Make sure screws are tight and cover is secured Driver Installation EP DKIT40D S 347V and EL DKIT36D S 347V Wiring Diagrams Dimming Type 1 10V Light Engine Dimming Type DA2. Dimming Type DALI VIOLET WHITE DALI PROG COMMON BLUE WHITE X VIOLET 0 10V DALI PROG RNTC BLACK WHITE X X GREY 0 10V RSET YELLOW X PSU RED Line BLACK BLUES Neutral WHITE Remote Switch DALI Optional Electrical Connections Remove cover Remove driver enclosure cover Carefully remove Install driver enclosure to a suitable structural member knockout for AC line input wires using two 20 screws From luminaire To dimming controller optional Q First connect the black line and white neutral wires Replace electrical enclosure cover Enclosure cover is on of the AC line to the black and white wires of the power top for installation supply using 18 24AWG 0 82 2 08mm twist on wire connectors Next connect the luminaire wires to the blue and red wires of the power supply Connect the green wires to the ground screw Driver Installation EP DKIT400 LN and EL DKIT360 S LN Wiring Diagram White White Orange Black Lutron Interface Violet White DALI PSU GND Green Yellow GND Violet DALI O 10V lt Neutral White N Grey 0 10V Switched Hot Out 0 10V Line Blac lt Line Black Constant Hot In ee Neutral HWhite lt E coSystem Link E1 EcoSystem 5 lt EcoSystem Link E2 Digital Link
3. is subject to change without notice All values are design or typical values when measured under laboratory conditions INDO84 101113
4. rating ee Meo nisl e Refer to the tc point located on power supply This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class A RFLD complies with the Canadian standard ICES 003 Ce DEFR de la classe A est conforme la NMB 003 du Canada Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense GE Lighting 1 888 MY GE LED 1 888 69 43 533 www gelighting com GE Lighting Solutions LLC is a subsidiary of the General Electric Company The GE brand logo Lumination are trademarks of the General Electric Company USG and Logix are trademarks of USG Interiors LLC 2013 GE Lighting Solutions LLC Information provided
5. GE Installation Guide Lighting Remote Driver Enclosure For EP and EL Series Features e For remote location application e Suitable for dry or damp locations BEFORE YOU BEGIN Read these instructions completely and carefully WARNING AVERTISSEMENT RISQUES DE DECHARGES ELECTRIQUES e Coupez l alimentation avant d inspecter installer ou d placer le luminaire e Assurez vous de correctement mettre la terre le boitier d alimentation lectrique RISK OF ELECTRIC SHOCK e Turn power off before inspection installation or removal e Properly ground electrical enclosure RISK OF FIRE RISQUES D INCENDIE e Respectez tous les codes NEC et codes locaux e N utilisez que des fils approuv s par UL pour les entr es sorties de connexion Taille minimum 18 AWG e Follow all NEC and local codes e Use only UL approved wire for input output connections Minimum size 18 AWG Save These Instructions Use only in the manner intended by the manufacturer If you have any questions contact the manufacturer Prepare Electrical Wiring Electrical Requirements pe e The LED driver must be supplied with 120 277 VAC 50 60 Hz in 120 277V application e For model code EL DKIT360 S 347V and EP DKIT400 S 347V the unit must be supplied with 347 VAC 60 Hz in 347V application e Connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker Use min 75 C supply cond
6. LI X VIOLET WHITE DALI PROG VIOLET 0 GREY 0 RED 10V DALI PROG 10V PSU COMMON BLUE WHITE X RNTC BLACK WHITE X RSET jYELLOW X Line BLACK Neutral HWHITE Transformer Remote Switch 0 10V 110V 0 10V DALI PROG Optional VIOLET WHITE VIOLET X GREY RED Light Engine Electrical Connections 1 See previous steps 1 and 2 DALI PROG 0 10V DALI PROG 0 10V COMMON HBLUE WHITE X RNTC BLACK WHITE X RSET YELLOW X Line BLACK Neutral HWHITE Transformer Remote Switch 0 10V DALI PROG DALI DALI PROG Optional To dimming controller optional luminaire using 18 24AWG 0 82 2 08mm twist on wire connectors Next connect the luminaire wires to the blue and red wires of the power supply Connect the green wires to the ground screw Replace driver enclosure cover Enclosure cover is on top for installation Troubleshooting Symptom Solution e Check input voltage and check power supply input output connections Luminaire does not light Checlecireut breaker Luminaire is dim e Maximum recommended supply wire length is exceeded e Ensure power supply temperature does not exceed its maximum
7. uctor Grounding Instructions e The grounding and bonding of the overall system shall be done in accordance with National Electric Code NEC Article 600 and local codes imagination at work Provided in the Package e Power supply rated 120 277V 50 60Hz e Grounding screw and washer e For model code EP DKIT400UEVVA and EL DKIT360 S LN use Lutron Ecosystem 0 10V interface e For model code EP DKIT400 S 347V and EL DKIT360 S 347V Transformer GETR480 277 250W Tools and Components Required e 2 Phillips head screwdriver e UL Recognized conduit connections per NEC CEC for nominal conduit trade sizes 1 2 or e UL Recognized wire connectors Optional If using a dimming controller connect matching colored wires together Risk of Damage Make sure that supply connection light fixture wiring and dimming cables are connected to proper driver inputs Wrong connection may cause damage to the product Must use UL approved conduit fittings for all enclosure box connections to prevent wire cuts by sharp edges and excessive strain on wiring Driver Installation EP DKIT400 and EL DKIT360 S Wiring Diagrams Dimming Type 1 10V X VIOLET WHITE DALI PROG COMMON BLUE WHITE X VIOLET 0 10V DALI PROG RNTC HBLACK WHITE X GREY 0 10V RSET YELLOW _X PSU RED Line BLACK BLUES Neutral Remote Switch 1 10V Optional
Download Pdf Manuals
Related Search