GE EL Series Installation Guide
Contents
1. GE Lighting Installation Guide Lumination Linear Suspended LED Luminaire EL Series Cable Suspension Surface Mount Driver BEFORE YOU BEGIN Read these instructions completely and carefully WARNING AVERTISSEMENT RISK OF ELECTRIC SHOCK e Turn power off before inspection installation or removal e Properly ground electrical enclosure RISK OF FIRE e Follow all NEC and local codes e Use only UL approved wire for input output connections Minimum size 18 AWG 0 82 mm3 Save These Instructions Use only in the manner intended by the manufacturer If you have any questions contact the manufacturer Important Wear work gloves to prevent dirt and oil from being transferred to the luminaire A CAUTION RISK OF DAMAGE e Luminaire may fall down if not installed properly e Remove protective film on Light Guide only after installation e Do not touch Light Guide to avoid dirt oil and fingerprints imagination at work RISQUES DE DECHARGES ELECTRIQUES e Coupez l alimentation avant d inspecter installer ou d placer le luminaire e Assurez vous de correctement mettre la terre le boitier d alimentation lectrique RISQUES D INCENDIE e Respectez tous les codes NEC et codes locaux e N utilisez que des fils approuv s par UL pour les entr es sorties de connexion Taille minimum 18 AWG 0 82 mm Tools and Components Required e 2 Philips head screwdriver e UL Recognized wire connect2. en the center of the outlet box to wall should be no less than 27 in Luminaire Installation Front cover Take out driver box from packaging Pull open front cover by disconnecting the clips on two end caps 2 x4 outlet box Ceiling s ry A Fastener Fastener Fastener Surface mount driver box Q Align the driver box with the 2 x4 outlet box Then mount the driver box to ceiling with 3 fasteners capable of supporting gt 30 Ibs each The outlet box should be aligned with the driver box allowing no exposed gaps to outlet box WARNING Use fasteners not supplied that are appropriate for use with your mounting surface and weight of the fixture Outlet box in ceiling Dimming line optional Connect wires from driver box to the wire leads in outlet box using wire nuts white to white black to black green to green Connect the dimming wires if needed Optional dimmer When connecting dimming controller wires must be run through a separate knockout hole equipped with bushing provided Risk of damage Make sure that supply connection light fixture wiring and dimming cables are connected to proper driver inputs Wrong connection may cause damage to the product Wear work gloves to prevent dirt and oil from being transferred to the luminaire Unpack Light Engine fro
3. m packaging Properly inspect for defects before installing Make sure the Light Engine is only carried out by holding two ends of it Do not touch Light Guide when taking out 5 Hold the Light Engine and move to suspension cable Connect two adjustable nuts to studs on top of the luminaire Before connecting flexible cord to the output wires of the driver form a knot in the end of the cord to act as a strain relief Be sure the knot is inside the enclosure Install wire clamp to top surface of the driver box and then connect the red line and black neutral wires from light engine to red line and blue neutral wires from the power supply Green wire to G position on driver box Suspension cable Driver box Flexible cord gt Connect the ground wire from front cover to the ground 8 Put back the front cover Push to get it snapped by two screw on the top plate Other wires hidden for clarity end caps Attached suspension cable and cords with plastic clips provided 0 10 volt Dimming At Controller LED Driver LED Driver 0 10V To 0 10V Dimmer DALI Prog To DALI Controller DALI Prog Optional Installation For 120 277V and 347V Application 0 10 Volt Dimming or DALI Lighting Controller Follow figure A for 0 10V and figure B for DALI Run wires from controller through a different knockout than the AC input wire At output side of LED Driver make appropriate connections using twist on
4. ors e UL Recognized outlet box 2 x4 e Ceiling fasteners 3 sets Prepare Electrical Wiring Electrical Requirements ea e The LED driver must be supplied with 120 277 VAC 50 60 Hz lin 120 277V application e For Series ELOXD the unit must be supplied with 347 VAC 60 Hz in 347V application e Connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker Use min 75 C supply conductor Grounding Instructions e The grounding and bonding of the overall system shall be done in accordance with National Electric Code NEC Article 600 and local codes Screw Holes Position On Ceiling For Mounting Driver Box Side view 550 mm 21 7 in 225 mm 8 9 in 325 mm 12 8 in lt lt a Outlet box Top view 5 mm 0 2 in Dimming control wire hole Main supply hole 3 mm 0 1 in 5 mm 0 2 in Luminaire Installation Position 382 mm Outlet box 15 0 in Ceiling 1215 mm 47 8 in 1219 mm 48 0 in 4 ft Luminaire When the outlet box mounted to ceiling the distance between the center of the outlet box to wall should be no less than 15 in E e a i Outlet box 687 mm 27 0 in C 1215 mm 47 8 in 1829 mm 72 0 in 6 ft Luminaire When the outlet box mounted to ceiling the distance betwe
5. se GE Lighting 1 888 MY GE LED 1 888 69 43 533 www gelighting com GE Lighting Solutions LLC is a subsidiary of the General Electric Company The GE brand logo Lumination are trademarks of the General Electric Company USG and Logix are trademarks of USG Interiors LLC 2013 GE Lighting Solutions LLC Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions INDO81 101113
6. wire connectors Follow lighting controller installation instructions Luminaire Inter Connection and Alignment Inter connector Light Guide clip Put inter connector on the top of two luminaires and make Push the inter connector into the luminaires Remove the sure that the slot of the inter connector cross the two end protective film and insert the Light Guide clip between caps the two Light Guides This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class A RFLD complies with the Canadian standard ICES 003 Ce DEFR de la classe A est conforme a la NMB 003 du Canada Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expen
Download Pdf Manuals
Related Search