GBC WIREPRO 1000 User's Manual
Contents
1. exclusive wire holder design that enables you to assemble your document as you punch making it easier to load paper onto the binding element than previous systems The WirePRO 1000 advanced punching technology also makes it easier to punch more paper at once while providing greater reliability A GETTING STARTED Push the handle A onto the shaft located on the right side of the machine see figure 1 Align the flat spot of the handle with the flat of the shaft and secure it with the allen wrench provided Insert U shaped wire support bracket into holes on top rear of machine Firmly push the female end of the power cord into the power cord receptacle A1 located on the back of the machine CAUTION Make sure this step is complete prior to plugging the male end of the power cord into a power receptacle Plug the male end of the power cord into an appropriate power receptacle DETERMINE SHEET WIDTH Set Edge Guide B to paper size you wish to bind 11 8 1 2 letter size 11 1 4 oversized cover A4 ring A5 Japan A4 see figure 1 When using oversized covers set the Edge Guide on Covers punch all of the covers for your job and set aside Move the Edge Guide back to the 11 setting to punch your contents then bind Raise lid on cover D and pull up appropriate selector pins to disengage punch pins that may nick the edge of your sheet To determine which pins should be pulled up follow the punch steps i2. unit on a secure stable work area to prevent the machine falling and possibly causing personal injury and damage to the unit e Follow all warnings and instructions marked on the product e Lift the machine from the bottom not the cover e Do not lift the machine by the cover or paper holder wire ELECTRICAL SAFEGUARDS The WirePRO 1000 must be connected to a supply voltage corresponding to the electrical rating of the machine as indi cated on the serial rating plate or in this manual CAUTION THE POWER RECEPTACLE MUST BE LOCATED NEAR THE EQUIPMENT AND BE EASILY ACCESSIBLE CAUTION IN CASE OF EMERGENCY USE THE POWER CORD AS A MAIN DISCONNECT DEVICE e Unplug the WirePRO 1000 before moving it or when it is not in use for an extended period of time e Do not operate with a damaged supply cord or plug after it malfunctions or after it has been damaged in any manner e Do not overload electrical outlets beyond their capacity as this can result in fire or electrical shock e Do not alter attachment plug Plug is configured for the appropriate electrical supply e The unit is intended for indoor use only e Never push objects into this product through cabinet slots Do not spill liquid of any kind on this product e Do not operate if the product has been exposed to rain or water SERVICE Do not attempt to service or repair the WirePRO 1000 your self Unplug the unit and contact an authorized GBC service representative for exchan
3. WirePROIOCOO Gi General Binding Corporation 0 pe ratin g Northbrook IL USA 60062 Instructions SAFETV MESSAGES Vour safetv as well as the safetv of others is important to GBC In this Operator Manual and on the product are impor tant safetv messages Read these messages caretuliv The safetv alert svmbol precedes each safetv message A in this Operator Manual This symbol indicates a potential personal safety hazard that could hurt you or others as well as cause product or property damage The following warning is found on this unit This safety message means you could be seriously hurt or killed if you open the product and expose yourself to hazardous voltage poo hanmou AN ie Rd cod WEE LT VERA The following symbols appear on this product and their meaning is as follows WARNING For vour protection do not connect the WirePRO 1000 to electrical power until vou read these instructions completelv Keep these instructions in a conve nient location for future reference To guard against injurv the following basic safetv precautions must be observed in the set up and use of this product IMPORTANT SAFEGUARDS GENERAL SAFEGUARDS Use the WirePRO 1000 only for its intended purpose of punching and binding paper and covers according to the indicated specifications e Do not place anything in the punch opening of the machine other than paper and cover stock e Place
4. d decrease it s thickness before trying to punch again BINDING Using the dial on the left side adjust the Wire Crimper to correspond with the wire element size to be used Place the large loops of the wire element into the Wire Holder as shown in figure 3 Be sure it is firmiv secured with the small loops facing toward you Place your punched pages face downward onto the small loops of the wire element Then place your front and back covers face to face against each other Place the covers onto the wire element with the back cover first and the inside of the front cover facing upward This step ensures that after crimping the seam of the wire element will be hidden between the back cover and last page figure 4 Hold the wire element firmly at each end of the book and remove it from the Wire Holder by sliding it to the left or lifting it off While firmly holding the wire element at each end place the book with the open end of the wire face down into the Wire Crimper You can release the book so it rests against the support rack or continue to hold it with one hand figure 5 To crimp the wire together pull the handle down toward you completely until it goes no further Remove the book and flip the front cover around to the front Your presentation is now complete F EMPTY CHIP DRAWER 1 Empty Chip Drawer F after repeated use Pull drawer gentiv toward you to open When putting back in the drawer will snap int
5. ge or repair CLEANING CAUTION Unplug this product before cleaning Wipe exterior only with a damp cloth Do not use detergents or solvents The following notes apply only to the units rated 230V SOHz MAIN CORDSET SELECTION FOR 230VAC MACHINES ONLY When choosing a detachable line cord for use with the WirePRO 1000 always observe the following The cordset consists of three components the attachment plug cordage and appliance inlet Each of these components must meet European regulatory approvals for safety The following minimum electrical ratings for the specific cordset are published for safety purposes DO NOT USE CORDSETS THAT DO NOT MEET THE FOLLOWING MINIMUM ELECTRICAL REQUIREMENTS PLUG 3A 250 volts 50 60 Hz Class 1 3 conductor European safety agency approved CORDAGE Type HOSVV F3G0 75 Harmonized lt 1 HAR D gt The lt j D symbols indicate cordage approved to appro priate European standard NOTE HAR may be substituted by the approval mark of the European safety agency which approved the cordage An example would be lt jVDE p gt APPLIANCE CONNECTOR 3A 250 volts 50 60 Hz European safety approved Type IEC 320 Cordset shall not exceed 3 meters in length Cordset with component electrical ratings greater than the minimum specified electrical ratings may be substituted Figure 2 Figure 5 gure 8 Thank you for purchasing the GBC WirePRO 1000 This system features our new
6. ndicated in section D using blank test paper DETERMINE WIRE SIZE Slide the Binder Sizer open C see figure 1 Place document including covers behind Binder Sizer Release the Binder Sizer and select the wire binding element that corresponds with the size shown by guide For best results always use GBC brand covers with GBC color coordinated wire PUNCHING PAPER see figure 2 Lift the Paper Support D into place optional Align sheets or covers and insert edge to be bound into punch throat Dt Jog the sheets until they are flush against the edge guide and the bottom of the punch throat Allow the paper to rest gt 0 N on eo o ta SPECIFICATIONS Dimensions 18 W x 8 1 2 H x 16 D 457mm x 216mm x 406mm Weight 36 Ibs 15 5 kg Electrical Power 115V AC 60Hz 2 0 amps or 230V AC 50Hz 1 2 amps an m land gt o against the Paper Support or you may prefer to hold the sheets in place with one hand To punch press the PUNCH button D2 The WirePRO 1000 punches up to 17 sheets of 20 Ib 80 gram paper at once Punch only TWO clear covers at a time to prevent jams and excessive wear If you try to punch too many sheets GBC s patented Jam Stopper safeguard feature will automatically stop and reverse the punch die At this time the yellow LED indicator will temporarily flash Remove the paper from the punch throat an
7. o place see figure 6 G SERVICE Should your WirePRO 1000 require service contact General Binding Corporation 6210 Capitol Dr Wheeling IL 60090 1 800 790 7787 Punch Capacity 17 sheets of 20 Ib paper 17 sheets of 80gm paper Bind Capacity 125 sheets or 9 16 14mm Maximum Sheet Width 11 7 297mm A4 Dis engagable Punch Pins 14
Download Pdf Manuals
Related Search