Garmin TR-1 Installation Instructions
Contents
1. holding the loop flat against the throttle bracket tighten the stop screw Rotate the tiller handle from idle to max throttle and verify that the throttle loop link does not bind anywhere With the tiller handle set to idle rotate the throttle bracket with your finger from idle to maximum throttle and verify it does not bind on the throttle loop link If any binding occurs readjust the stop screw LAW J oye Da HOLDER THROTTLE LOOP LINK CIRCUIT BOARD _ MOUNTING SCREWS Step Four Install the throttle actuator assembly STOP BLOCK Verify that the outside edge of the stop block is approximately flush with the end of the motor lead screw If not loosen the stop block set screw and slide the stop block to the end of the shaft Retighten the set screw Push the STOP BLOCK FLUSH motor lead screw until the stop block activates WITH LEAD SCREW closes the limit switch The inner edge of the stop block should be almost in contact with the motor If necessary loosen the circuit board mounting screws and slide the circuit board forward or backward to allow the stop block to activate the limit switch properly STOP BLOCK LIMIT SWITCH Push Until limit Switch is Activated Remove one of the bolts holding down the recoil starter Place the lock washer on the bolt and restart it in the mounting hole Place the flange of the actuator assembly under the lock washer and tighten the bolt The motor lead screw s2. A GARMIN TR 1 Gold Throttle Actuator Installation Instructions Honda 8 HP 1987 2000 PN 906 1160 00 Parts Kit Number 120 0052 01 Lock Washe lt lt cl Sun o Screw UN k f Spacer dA r a i v Rje ron Throttle loop link Bracket Tm 6 310 004023 Washer Nylon 4 250D _ 1 8 310 0073 06 Washer Locking Internal Step One Remove Throttle Rod DA THROTTLE ROD STOP SCREW Loosen the stop screw Using the tiller grip rotate the throttle arm until the throttle rod is free from the holder on the throttle arm Lift the throttle rod and remove it from the throttle lever Step Two Install the throttle bracket j rE ER ase ae Slide the throttle bracket under the throttle lever Secure the throttle bracket to the throttle lever using the 4 40 x 9 16 phillips head screw and the 1 4 inch diameter spacer and the washer da i a i F uri Step Three Install the throttle loop link Hook the loop end of the throttle loop link around the spacer on the throttle bracket Using the tiller grip rotate the throttle arm and place the other end of the throttle loop link into the holder on the throttle arm With the tiller handle set to idle or full slow position adjust the throttle loop link so that there 1s approximately 1 mm clearance between the inside edge of the loop and the spacer on the throttle bracket While
3. ROW button on the Handheld verify that the engine rpm s go up Using the IDLE RESUME button on the handheld verify that the engine returns to idle Check the throttle up and down several times along with the idle res and verify that you don t have any problems
4. hould point just outside the outer edge of the square block on the end of the throttle bracket With the motor lead screw fully extended rotate the throttle bracket with your finger to verify that it clears the motor lead screw If it does not loosen the bolt and reposition the actuator assembly Make sure the tiller grip is set to idle and that the carburetor throttle lever 1s against the throttle idle adjust screw Throttle bracket must clear end of motor lead screw when bracket is rotated With a slight loop in the throttle pull line between the motor and the throttle bracket place the pull line in the slot of the throttle bracket and wrap it around the bracket and in the slots twice Place the lock screw in the throttle bracket and tighten to secure the pull line Throttle pull line Testing the Actuator Functions Please refer to the startup section of your owner s manual before operating your handheld and running the throttle actuator 1 With the outboard in the water or with a proper coolant flush device connected start the outboard and let it warm up to operating conditions Be prepared to kill the outboard ignition if the idle speed is too high when the engine starts 2 With the outboard in idle position make sure there is proper slack in the pull string on the throttle actuator If the motor does not go to idle reposition the string by loosening the pinch screw on the brass pivot 3 Using the UP AR
Download Pdf Manuals
Related Search