Garmin 10V Installation Instructions
Contents
1. e If you reach planing speed through adding increments of 200 RPM and the autotune procedure continues to fail reduce speed below planing speed and select Alternate Autotune to begin an alternate autotuning procedure CAUTION The Alternate Autotune is only applicable to a small number of boats and should be the last attempt at autotuning Do not perform the Alternate Autotune until you are sure the standard autotune procedure will not work on your boat 5a Set North with an optional GPS device connected To perform this step you must have a large stretch of open water available Be sure to have at least 45 seconds of hazard free open water available while at planing speed Drive the boat in a straight line at planing speed and select Begin when you are ready When the GHC 10 displays a completion message select Done If the calibration fails select Retry to begin the process again 5b Fine Heading Adjustment without an optional GPS device connected To perform this step manually adjust the heading to match a compass on the boat or other known heading reference Evaluating the Results of the Autopilot Configuration When the Sea Trial Wizard is complete test the autopilot to be sure it is configured correctly Test the autopilot first at slow speeds below planing and then test the autopilot at planing speeds To test the autopilot configuration 1 Drive the boat in one direction with the autopilot engaged heading hold The2. 0183 compatible GPS device to use waypoint and route information with the GHP 10V although a NMEA 2000 compatible GPS device is preferred To wire the GHC 10 to power 1 Route the GHC 10 power data cable to the boat battery 2 Connect the red or positive wire to the positive voltage terminal If you use the fuse block on the boat route the positive connection through the fuse 3 Connect the black or ground wire to the negative voltage terminal 4 Install or check the AGC 3AG 1 A fuse on the fuse block or in the in line holder 5 Connect the power data cable to the GHC 10 Notes e The replacement fuse is an AGC 3AG 1 A fuse e If itis necessary to extend the power wires use 18 AWG wire e If your boat has an electrical system you might be able to wire the GHC 10 directly to an unused holder on your current fuse block If you are using the fuse block remove the in line fuse holder supplied with the GHC 10 A CAUTION The GHC 10 maximum input voltage is 32 Vde Do not exceed this voltage because this can damage the GHC 10 and void the warranty NOTE During a typical installation use only the red black and yellow wires The other wires are used for NMEA 0183 connections and do not have to be connected for normal operation of the GHC 10 For information on connecting to a NMEA 0183 compatible GPS device see page 12 To wire the yellow CCU signal wire from the GHC 10 power data cable to the CCU cable 1 R
3. Checklist Detach this checklist from the installation instructions and use it to assist with the GHC 10 installation process Read all installation instructions before installing the GHC 10 Contact Garmin Product Support if you have any questions during the installation process OU O OU OUL 1 Refer to the diagram and notes starting on page 5 to understand the necessary electrical and data connections 2 Lay out all of the components first Check the cable lengths Obtain extensions if necessary 3 Mount the CCU by following the directions starting on page 6 Mount the CCU in a location free of magnetic interference Use a handheld compass to test for magnetic interference in the area Mount the CCU in the bracket so that the wires hang straight down 4 Mount the GHC 10 by following the directions starting on page 8 5 Mount the Autopilot Gateway by following the directions on page 7 6 Connect the Autopilot Gateway to the Volvo multilink bus see page 7 7 Connect the Autopilot Gateway to the CCU using the CCU cable see page 7 8 Connect the GHC 10 and the CCU to a NMEA 2000 network Connect an optional NMEA 2000 compatible GPS device to the NMEA 2000 network see page 9 9 Wire the GHC 10 to power and to the yellow CCU signal wire on the CCU cable Wire an optional NMEA 0183 compatible GPS device to the GHC 10 if a NMEA 2000 compatible GPS device is not available see page 9 10 Apply a corrosion blocker to all the inst
4. Receive PGN List Group Function 126464 Transmit Receive PGN List Group Function 126996 Product Information 126996 Product Information 127250 Vessel Heading 129025 Position Rapid Update 127488 Engine Parameters Rapid Update 129026 COG amp SOG Rapid Update 129025 Position Rapid Update 129029 GNSS Position Data 129029 GNSS Position Data 129283 Cross Track Error 129284 Navigation Data 129284 Navigation Data 129285 Navigation Route WP information 129285 Navigation Route WP information 129540 GNSS Sats in View CCU Receive Transmit 059392 ISO Acknowledgment 059392 ISO Acknowledgment 059904 ISO Request 059904 ISO Request 060928 ISO Address Claim 060928 ISO Address Claim 126208 NMEA Command Request Acknowledge Group 126208 NMEA Command Request Acknowledge Group Function Function 126996 Product Information 126464 Transmit Receive PGN List Group Function 127258 Magnetic Variation 126996 Product Information 127488 Engine Parameters Rapid Update 127250 Vessel Heading 129025 Position Rapid Update The GHP 10 and the GHC 10 129026 COG amp SOG Rapid Update are NMEA 2000 certified 129283 Cross Track Error 129284 Navigation Data NMEA 0183 Information The GHC 10 when connected to an optional NMEA 0183 compatible GPS device uses the following NMEA 0183 sentences Receive wpl gga grme gsa gsv rmc bod bwc dtm gll rmb and xte Transmit hdg 18 GHP 10V Installation Instructions GHP 10V Installation
5. boat should not oscillate significantly however a small amount of oscillation is normal 2 Turn the boat in one direction using the autopilot When you release the turn button the boat should overshoot the turn and quickly correct the heading to the point at which you released the button You will notice that the faster you are going the greater the boat will overshoot the turn 3 When the autopilot turns the boat it should not feel as though it turns too aggressively or too sluggishly 4 If the autopilot is configured properly at slow speeds repeat these tests at planing speed and vice versa To adjust the autopilot rudder gain configuration if necessary 1 If you feel that the heading hold oscillates significantly or that the autopilot does not quickly correct the heading when turning you can make slight adjustments to the rudder gain NOTE When you manually adjust the rudder gain or counter gain make small adjustments and adjust only one value at a time Test the change before entering any further adjustments 2 Power on the GHP 10V using the advanced configuration power on procedure page 13 3 On the GHC 10 select Menu gt Setup gt Dealer Autopilot Configuration gt Turn Fine Tuning Setup gt Rudder Gains to access the rudder gain adjustments There are two types of gain settings at both low and high speeds e Rudder Gain Adjusts how aggressively the rudder holds the heading and makes turns If you set this va
6. immediately Main Components The GHP 10V autopilot system consists of three main components the Course Computer Unit CCU Autopilot Gateway and the GHC 10 user control interface Course Computer Unit CCU The CCU acts as the brain of the GHP 10V autopilot system The CCU contains the sensory equipment used to determine heading and rate of turn The CCU connects to the Autopilot Gateway to the GHC 10 yellow signal wire and to the alarm buzzer using the CCU cable In addition the CCU also connects to a NMEA 2000 network to communicate with the GHC 10 and to communicate with an optional NMEA 2000 compatible GPS device Garmin replacement part number 010 11353 00 Serial number The Autopilot Gateway allows the GHP 10V autopilot system to steer the boat through the Volvo steering system The Autopilot Gateway connects to the CCU through the CCU cable and connects to the Volvo steering system using a proprietary Volvo connector Garmin replacement part number 010 11349 00 Serial number Use the GHC 10 to operate the GHP 10V autopilot system Using the GHC 10 you engage and control the GHP 10V You also set up and customize the GHP 10V using the GHC 10 The GHC 10 connects to a NMEA 2000 network to communicate with the CCU and with an optional NMEA 2000 compatible GPS device to use waypoint and route information If a NMEA 2000 compatible GPS device is not available you can wire the GHC 10 to an optional NMEA 0183 c
7. prudent operation of your vessel The GHP 10V is a tool that will enhance your capability to operate your boat It does not relieve you from the responsibility of safely operating your boat Avoid navigational hazards and never leave the helm unattended Always be prepared to promptly regain manual control of your boat Learn to operate the GHP 10V on calm and hazard free open water Use caution when operating the GHP 10V at high speeds near hazards in the water such as docks pilings and other boats See the mportant Safety and Product Information guide in the product box for product warnings and other important information A Cautions e Always wear safety goggles ear protection and a dust mask when drilling cutting or sanding e When drilling or cutting always check the opposite side of the surface Be aware of fuel tanks electrical cables and hydraulic hoses e Do not connect the CCU interface connector on either the CCU cable or the Autopilot Gateway to a NMEA 2000 network September 2009 190 01082 02 Rev B Printed in Taiwan GHP 10V Package Contents and Needed Tools The GHP 10V autopilot system consists of multiple components each sold separately You must know how the components operate together in order to correctly plan the installation on your boat As you familiarize yourself with the GHP 10 components confirm that your package includes the following items If any parts are missing contact your Garmin dealer
8. 00 network backbone connect an appropriate NMEA 2000 backbone extension cable not included to the side of the T connector you disconnected 4 Add the included T connector for the GHC 10 to the NMEA 2000 network by connecting it to the side of the T connector you disconnected 5 Route the included drop cable to the bottom of the T connector you just added to your NMEA 2000 network If the included drop cable is not long enough you can use a drop cable up to 20 ft 6 m long not included 6 Connect the drop cable to the T connector and the GHC 10 GHC 10 CCU GARMIN m Optional T NMEA 2000 X i GPS device not included Additional bl drop cable Drop cable Drop cabe znd included included T connector not included T connector a T connector included S included MIN MIN E 3 O O O Existing NMEA 2000 network gt Connecting the GHC 10 and CCU to an Existing NMEA 2000 Network RMN To connect the CCU to your existing NMEA 2000 network Connect the CCU to your existing NMEA 2000 network by following the procedures you used to connect the GHC 10 to your existing NMEA 2000 network above Notes e Neither the CCU nor the GHC 10 is powered by the NMEA 2000 network They must be s
9. 2 Vdc battery Drop cables i T connectors Female terminator Male terminator Creating a Basic NMEA 2000 Network for the GHC 10 and the CCU Notes e To add additional sensors to your NMEA 2000 network follow the instructions included with the sensors e The GHC 10 is not powered by the NMEA 2000 network It must be separately connected to the power source e The GHC 10 must also connect to the CCU with the yellow CCU signal wire in the GHC 10 power data cable GHP 10V Installation Instructions 11 Connecting an Optional GPS Device to the GHP 10V Autopilot System To use an optional optional GPS device with the GHP 10V either connect a NMEA 2000 compatible GPS device to the NMEA 2000 network or connect a NMEA 0183 compatible GPS device directly to the GHC 10 To connect an optional NMEA 2000 compatible GPS device to your GHP 10V 1 Add an additional T connector not included for the optional GPS device you want to add to the NMEA 2000 network 2 Connect the GPS device to the T connector by following the instructions provided with the GPS device To connect an optional NMEA 0183 compatible GPS device to your GHP 10V 1 Determine the NMEA 0183 wiring assignments of your NMEA 0183 compatible GPS device 2 Use the GHC 10 power data cable wiring diagrams to correctly wire your NMEA 0183 compatible GPS device 3 Use 22 AWG twisted pair wire for extended runs of wire 4 Solder and cover all bare wire connecti
10. A GARMIN GHP 10V Installation Instructions To obtain the best possible performance and to avoid damage to your boat install your GHP 10V marine autopilot system according to the following instructions Read all installation instructions before proceeding with the installation If you experience difficulty during the installation contact Garmin Product Support or seek the advice of a professional installer The GHP 10V is compatible with C3 or newer Volvo EVC systems Contact Volvo for information on updating older EVC systems Product Registration Help us better support you by completing our online registration today Connect to our Web site at http my garmin com Keep the original sales receipt or a photocopy in a safe place For future reference write the serial number assigned to each component of your GHP 10V system in the spaces provided on page 2 The serial numbers are located on a sticker on each component Contact Garmin Contact Garmin Product Support if you have any questions while installing or using your GHP 10V autopilot system In the USA go to www garmin com support or contact Garmin USA by phone at 913 397 8200 or 800 800 1020 In the UK contact Garmin Europe Ltd by phone at 0808 2380000 In Europe go to www garmin com support and click Contact Support for in country support information or contact Garmin Europe Ltd by phone at 44 0 870 8501241 Warnings You are responsible for the safe and
11. Ltd or its subsidiaries registered in the USA and other countries GHP GHC and myGarmin are trademarks of Garmin Ltd or its subsidiaries These trademarks may not be used without the express permission of Garmin Volvo is a registered trademark of Volvo Trademark Holding AB NMEA 2000 is a registered trademark of the National Marine Electronics Association Loctite and Pro Lock Tight are registered trademarks of Henkel Corporation For the latest free software updates excluding map data throughout the life of your Garmin products visit the Garmin Web site at www garmin com A GARMIN 2009 Garmin Ltd or its subsidiaries Garmin International Inc 1200 East 151 Street Olathe Kansas 66062 USA Garmin Europe Ltd Liberty House Hounsdown Business Park Southampton Hampshire S040 9LR UK Garmin Corporation No 68 Jangshu 2nd Road Shijr Taipei County Taiwan www garmin com September 2009 190 01082 02 Rev B Printed in Taiwan
12. The NMEA 2000 cables connect the CCU and the GHC 10 to the NMEA 2000 network Use the NMEA 2000 power cable and two terminators to create a NMEA 2000 network on your boat if one does not exist Additional NMEA 2000 cables and connectors are available if necessary You can use a NMEA 2000 drop cable to extend the CCU cable if necessary For more information on NMEA 2000 see page 9 gt I 7 LW RAI N NMEA 2000 drop cable 6 1 2 ft 2 m two included Garmin replacement part number 010 11076 00 NMEA 2000 power cable one included Garmin replacement part number 010 11079 00 NMEA 2000 T connector three included Garmin replacement part number 010 11078 00 NMEA 2000 terminators one of each included Garmin replacement part number male 010 11080 00 Garmin replacement part number female 010 11081 00 Tools e Safety glasses e Waterproof wire connectors e Drill and drill bits e Compass to test for magnetic interference when finding a 31 32 in 90 mm hole saw suitable location for the CCU e Scissors e Surface specific mounting hardware screws or bolts e Wire cutters strippers e Marine sealant e File and sandpaper e Anti seize lubricant optional e Phillips screwdriver and flat screwdriver e Additional NMEA 2000 cables and connectors optional e Cable ties NOTE Mounting screws are provided for the GHC 10 and for the CCU If the provided screws are not appropriate for the mou
13. alled components except the GHC 10 Bio Shield or Corrosion X for example 11 Configure the GHP 10V system by completing the Sea Trial Wizard see page 13 CCU Mounting Template Up when mounting on a vertical surface GHP 10V Installation Instructions 19 2009 Garmin Ltd or its subsidiaries All rights reserved Except as expressly provided herein no part of this manual may be reproduced copied transmitted disseminated downloaded or stored in any storage medium for any purpose without the express prior written consent of Garmin Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited Information in this document is subject to change without notice Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements Visit the Garmin Web site www garmin com for current updates and supplemental information concerning the use and operation of this and other Garmin products Garmin and GPSMAP are registered trademarks of Garmin
14. avigation Setup gt NMEA Setup NMEA Checksum If the connected GPS unit incorrectly calculates checksums you may still be able to use it if you turn this setting off When off data integrity is compromised Navigation Setup gt NMEA Setup Reversed XTE If the connected GPS unit sends the incorrect steering direction with the cross track error signal use this setting to correct the steering direction Navigation Setup Navigation Gain Because the cross track error data transmitted by a NMEA 0183 GPS device is only accurate within 01 mile 60 ft the gain may need adjustment Increase this setting until the boat oscillates back and forth near the course line then lower it a few levels Navigation Setup Navigation Trim Gain After adjusting the Navigation gain increase this setting until you can see the standoff from the course line decreasing over time NOTE Certain configuration settings are available when using the GHC 10 normally such as enabling and disabling the Shadow Drive adjusting the sensitivity of the Shadow Drive and adjusting the Sea State Filtering setting See the configuration section of the GHC 10 Quick Start Manual for more information 16 GHP 10V Installation Instructions Appendix Specifications CCU Physical Dimensions 31 32 in 91 4 mm diameter Weight 5 6 oz 159 g Temperature Range from 5 F to 131 F from 15 C to 55 C Case Material Fully gasketed high impact plastic alloy waterproof t
15. eparately connected to power sources see pages 7 and 9 e The GHC 10 must also connect to the CCU with the yellow CCU signal wire in the GHC 10 power data cable e To add additional sensors to your NMEA 2000 network follow the instructions included with the sensors 10 GHP 10V Installation Instructions To create a basic NMEA 2000 network for the GHC 10 and the CCU 1 Connect three T connectors two of the three are not included together by their sides 2 ANMEA 2000 power cable not included must be connected to a 12 Vdc power source through a switch Connect to the ignition switch of the boat if possible or through an appropriate additional switch not included Connect a NMEA 2000 power cable not included to one of the T connectors Connect the included NMEA 2000 drop cable to one of the T connectors and to the GHC 10 Connect a NMEA 2000 drop cable not included to the remaining T connector and to the CCU Connect the appropriate NMEA 2000 terminators not included to each end of the combined T connectors aon A Ww CAUTION You must connect the NMEA 2000 power cable to the boat ignition switch or through another in line switch The GHC 10 will drain your battery if it is connected directly GHC 10 Ignition or in line switch Ground and use drain wires Power cable 1
16. f the CCU cable to the location where you plan to access the Volvo multilink bus and install a NMEA 2000 drop cable extension not included if necessary Connect the cable to the Autopilot Gateway after you have installed the gateway page 7 Route the bare wire end of the CCU cable to the location best suited to wire it to power to the alarm buzzer and to the GHC 10 Wire the CCU to the alarm buzzer and to the GHC 10 after you have installed the alarm buzzer and the GHC 10 see pages 7 and 8 To wire the CCU to power 1 On the bare wire end of the CCU cable isolate the red and black wires 2 Connect the red or positive and black or ground wires to power and ground through the ignition switch or through an external switch If the red and black wires are not long enough extend the appropriate wires with 22 AWG wire 3 Solder and cover all bare wire connections Installing the Autopilot Gateway The Autopilot Gateway allows the GHP 10V Autopilot System to communicate with the Volvo EVC system and steer the boat Mounting the Autopilot Gateway Mount the Autopilot Gateway near the location where you plan to access the Volvo proprietary multilink bus and ensure that the Volvo interface cable reaches the location where you plan to access the Volvo multilink bus Secure the Autopilot Gateway with cable ties or other appropriate mounting hardware not included Connecting the Autopilot Gateway 1 O
17. gains you do not feel as though the GHP 10V is working correctly you can run the wizard again at any time To manually run the Sea Trial Wizard 1 Power the GHC 10 on using the advanced configuration power on procedure page 13 2 From the Heading screen select Menu gt Setup gt Dealer Autopilot Configuration gt Wizards gt Sea Trial Wizard 3 Perform the steps as prompted For more information see page 13 Changing Advanced Configuration Settings You can run the Autotune automated configuration process calibrate the compass and define North on the GHP 10V through the GHC 10 without running the wizards Additionally without running the wizards you can individually define each configuration setting To access the automated configuration settings and the advanced configuration settings power on the GHC 10 using the advanced configuration power on procedure see page 13 To manually run the automated configuration settings 1 From the Heading screen select Menu gt Setup gt Dealer Autopilot Configuration gt Automated Setup 2 Select Autotune Calibrate Compass or Set North 3 Perform the steps as prompted as you would if you were running the Sea Trial Wizard For more information on each automated configuration setting see page 13 To manually define individual configuration settings 1 From the Heading screen select Menu gt Setup gt Dealer Autopilot Configuration 2 Select the appropriate category of the set
18. lue too high the autopilot may be overactive constantly adjusting the rudder in reaction to slight heading deviations which can lead to undesired rudder oscillation An overactive autopilot can cause excess wear and tear on the steering system If this value is too low the autopilot will be slower to execute course changes and will allow more error around your desired heading e Counter Gain Adjusts how tightly the rudder corrects the turn overshoot If you set this value too low the autopilot can excessively overshoot on course changes If this value is too high the pilot will be slow to execute course changes and will seem less responsive To adjust the autopilot turning configuration if necessary 1 If you feel that the autopilot turns the boat too aggressively or too sluggishly you can make slight adjustments to the turn acceleration limiter A NOTE When you manually adjust the acceleration limiter make small adjustments Test the change before entering any further adjustments 2 Power on the GHP 10V using the advanced configuration power on procedure page 13 3 On the GHC 10 select Menu gt Setup gt Dealer Autopilot Configuration gt Turn Fine Tuning Setup gt Acceleration Limiter 14 GHP 10V Installation Instructions Manually Running the Sea Trial Wizard The Sea Trial Wizard allows you to quickly define all of the important configuration settings on the GHP 10V If after running the wizard and manually adjusting the
19. nting surface you will need to provide the correct types of screws GHP 10V Installation Instructions Preparation Before installing the GHP 10V autopilot system it is important that you completely understand where all the components will be located on your boat Temporarily place all the components where you plan to install them Ensure that all cables can reach the necessary components before mounting any of the components Electrical Data Connection and Mounting Considerations The GHP 10 components connect to each other and to power using the included cables Ensure that the correct cables reach each component and ensure that each component is in an acceptable location before mounting any components Read the following considerations and consult the diagram on the next page before you begin installation CCU e Do not mount the CCU in a location where it will be submerged or exposed to wash down e Mount the CCU in the forward half of the boat no higher than 10 ft 3 05 m above the waterline e You can mount the CCU below the waterline as long as it is not in a location where it will be submerged or exposed to wash down e Mount the CCU bracket on a vertical surface or under a horizontal surface so that the connected wires hang straight down e Do not mount the CCU near magnetic material magnets speakers and electric motors or high current wires Mount the CCU at least 24 in 0 61 m away from movable or changing magnetic dis
20. o IEC 529 IPX7 standards CCU Cable Length 91 2 ft 3 m Power Power Input 9 33 Vdc NMEA 2000 Power Input 9 16 Vdc NMEA 2000 LEN 2 100 mA Autopilot Gateway Physical Dimensions WxHxD 51 s x 23 s x 1 in 130 x 60 x 25 mm Weight Less than 1 oz 28 g Alarm Buzzer Dimensions L x Diameter 29 32 in x 1 in 23 mm x 25 mm Weight 2 4 oz 68 g Temperature Range from 5 F to 131 F from 15 C to 55 C Cable Length 10 ft 3 0 m GHC 10 Physical Dimensions WxHxD 45 16 x 43 s x 12 32 in 109 x 48 x 111 mm Weight 9 6 oz 272 g Cables Power data cable 6 ft 1 8 m NMEA 2000 drop cable and power cable 61 2 ft 2 m Temp range from 5 F to 158 F from 15 C to 70 C Compass Safe Distance 9 2 in 241 mm Case Material Fully gasketed high impact plastic alloy waterproof to IEC 529 IPX7 standards Power GMI 10 power input source 8 32 Vdc Fuse AGC 3AG 1A GMI 10 power usage 2 5 W max NMEA 2000 Power Input 9 16 Vdc NMEA 2000 LEN 2 100 mA GHP 10V Installation Instructions NMEA 2000 PGN Information GHC 10 Receive Transmit 059392 ISO Acknowledgment 059392 ISO Acknowledgment 059904 ISO Request 059904 ISO Request 060928 ISO Address Claim 060928 ISO Address Claim 126208 NMEA Command Request Acknowledge Group 126208 NMEA Command Request Acknowledge Group Function Function 126464 Transmit
21. ompatible GPS device instead Garmin replacement part number 010 00688 00 Serial number Cables and Connectors Use the included cables to connect the GHP 10V components to power to each other to an alarm provided and to optional devices such as a NMEA 2000 or NMEA 0183 compatible GPS device CCU cable Use this cable to connect the CCU to the Autopilot Gateway Additionally a portion of this cable contains color coded wires with bare ends Use these wires to connect the CCU to power to the GHC 10 yellow signal wire NB and to the included alarm You can use a NMEA 2000 drop cable to extend ao YE oD Us J j the CCU cable if necessary though you should not connect this cable to a NMEA 2000 network Garmin replacement part number 010 11351 00 A CAUTION Do not connect this cable to a NMEA 2000 network 2 GHP 10V Installation Instructions GHC 10 Power Data Cable Use this cable packaged with the GHC 10 to connect the GHC 10 to power to the CCU and to an optional NMEA 0183 compatible GPS device if you do not have a NMEA 2000 compatible GPS device on the NMEA 2000 network Garmin replacement part number 010 11074 00 Alarm Wire the included alarm to the CCU using the CCU cable The alarm provides audible alerts from the GHP 10V Garmin replacement part number 010 11056 00 NMEA 2000 Cables and Connectors
22. ons ye Color Function GHC 10 Device Fuse Red Power a apa 1A Black Ground L_carmin MJ Yellow CCU Signal gt Blue Tx A gt White Tx B lt Brown Rx A lt Green Rx B GHC 10 Power Data Cable Example A acio a 4A WIRE FUNCTION Fuse RED POWER E J TA BLACK POWER GND N BROWN Tx A N BLUE Rx A YELLOW to CCU Wiring the GHC 10 to a NMEA 0183 Compatible Device NMEA 0183 Compatible Device Notes e Consult the installation instructions for your NMEA 0183 compatible device to identify the Transfer Tx A and B wires e If your NMEA 0183 compatible device has only one transmitting wire Tx connect it to the brown wire Rx A from the GHC 10 and connect the green wire Rx B to ground e If your NMEA 0183 compatible device has only one receiving wire Rx connect it to the blue wire Tx A from the GHC 10 and leave the white wire Tx B unconnected e The yellow CCU signal wire must be wired to the yellow wire of the CCU cable 12 GHP 10V Installation Instructions Configuring the GHP 10V The GHP 10V autopilot system must be configured and tuned to your boat dynamics and motor configuration A NOTE The Dockside Wizard and any hydraulic setup options are not used when configuring the GHP 10V autopilot system Advanced Configuration Power on Procedure Advanced configuration options a
23. oute the GHC 10 power data cable to the bare end of the color coded wires from the CCU cable If the cable is not long enough extend the yellow CCU signal wire with 22 AWG wire 2 Connect the yellow CCU signal wire from the GHC 10 power data cable to the yellow wire on the CCU cable If you install multiple GHC 10 units and want to turn the GHP 10V autopilot system on with any of the installed GHC 10 units connect all of the yellow CCU signal wires from the GHC 10 units to the yellow wire on the CCU cable 3 Solder and cover all bare wire connections NOTE The yellow CCU signal wire must be connected from the GHC 10 power data cable to the CCU cable or else the GHP 10V autopilot system will not power on with the GHC 10 Connecting the GHC 10 to a NMEA 2000 Network Connect the GHC 10 to the CCU through your existing NMEA 2000 network If you do not have an existing NMEA 2000 network on your boat you will need to create one Optionally you can connect a NMEA 2000 compatible GPS device to your NMEA 2000 network to use waypoint and route information with the GHP 10V For more information on NMEA 2000 visit www garmin com GHP 10V Installation Instructions 9 To connect the GHC 10 to your existing NMEA 2000 network 1 Determine where you would like to connect the GHC 10 to your existing NMEA 2000 network 2 Disconnect one side of a NMEA 2000 T connector from the network at an appropriate location 3 If you need to extend the NMEA 20
24. p you are ready to start the Sea Trial Wizard You must complete the Sea Trial Wizard before you can use the autopilot system to control your boat The Sea Trial Wizard configures the fundamental sensors on the autopilot and it is extremely important to complete the wizard in conditions appropriate for your boat In general it is highly recommended to complete the Sea Trial Wizard in calm water with little or no wind Because the nature of calm water is relative to the size and shape of your boat be sure you choose a location where e Your boat does not rock while sitting still or moving very slowly e Your boat is not significantly affected by the wind While completing the Sea Trial Wizard in calm water it is important to observe the following e Keep the weight on your boat balanced DO NOT move around on the boat while completing any of the steps in the Sea Trial Wizard e Be sure that the engines are trimmed down and that the trim tabs are up To complete the Sea Trial Wizard configuration 1 Drive to calm open water and select Begin to start the Sea Trial Wizard from the welcome screen on the GHC 10 If the welcome screen is not showing select Menu gt Setup gt Dealer Autopilot Configuration gt Wizards gt Sea Trial Wizard 2 Planing RPM Take note of the RPM reading from the tachometer on the dashboard of your boat at the point your boat transitions from displacement to planing speed If the tachometer value does no
25. pen the Volvo multilink bus and disconnect the multilink breakout cable 2 Connect the proprietary Volvo connector from the Autopilot Gateway to the multilink bus using the included Y cable 3 Close the Volvo multilink bus 4 Connect the CCU interface connector Q to the CCU cable Autopilot Gateway Connectors A CAUTION Do not connect the CCU interface connector on either the CCU cable or the Autopilot Gateway to a NMEA 2000 network Installing the Alarm Buzzer The alarm buzzer audibly alerts you to important GHP 10V events Mounting the Alarm Buzzer Mount the alarm buzzer near the helm station You can mount the alarm buzzer under the dashboard if you prefer Secure the alarm buzzer with cable ties or other appropriate mounting hardware not included Wiring the Alarm Buzzer 1 Route the alarm buzzer cable to the bare wire end of the CCU cable If the cable is not long enough extend the appropriate wires with 28 AWG wire 2 Use the table below to make the appropriate connections Alarm Buzzer Wire Color CCU cable Wire Color White Orange Black Blue Alarm Buzzer Wiring Table 3 Solder and cover all bare wire connections GHP 10V Installation Instructions 7 Installing the GHC 10 Install the GHC 10 by flush mounting it in the dashboard near the helm connecting it to power and to the yellow CCU signal wire from the CCU cable and connecting it to a NMEA 2000 network Optionally
26. re not available on the GHC 10 under normal usage conditions To access the advanced configuration settings of the GHP 10V use the advanced configuration power on procedure NOTE The first time you power on the GHP 10V you will be prompted to complete the Sea Trial Wizard You do not need to power on the unit using this power on procedure to run the wizard for the first time Only use this procedure if you wish to fine tune the autopilot or re run the Sea Trial Wizard in the future To perform the advanced configuration power on procedure 1 With the power off press both the center and the right soft keys on the GHC 10 2 While holding the center and the right soft keys press and hold the Power key 3 Hold all 3 keys until the heading screen appears and then release the keys Hold these and power the soft keys GHC 10 on To ensure that the advanced configuration options are available 1 From the heading screen select Menu gt Setup GARMIN 2 If the option for Dealer Autopilot Configuration is available you correctly performed the advanced Advanced Configuration configuration power on procedure Power on Procedure 3 See page 15 for more information on the settings available under Dealer Autopilot Configuration The Sea Trial Wizard The first time you power on the GHP 10V you are prompted to complete a short setup sequence on the GHC 10 Use the soft keys to select the settings After you complete the initial setu
27. signal wire see page 9 8 32 Vdc GHC 10 1A fuse Black NMEA 2000 network imu see page 9 Q e S x TS Poel E Ignition or m fT in line switch l P4 Red 9 16 Vdc 3A fuse Black NMEA 2000 power cable Ignition or in line switch Red E a 8 32 Vdc 1A fuse Black GHP 10V Autopilot Gateway Orange White Alarm buzzer For CCU bare wire connections see page 9 ox a Kg AL loll Blue Black Yellow CCU signal wire see page 9 Qed GHP 10V General Wiring Diagram GHP 10V Installation Instructions an Installation Procedures After you have completely planned the GHP 10V installation on your boat and have satisfied all the mounting and wiring considerations for your particular installation you can begin mounting and connecting the components Installing the Course Computer Unit CCU Install the CCU by mounting it to your boat connecting it to the Autopilot Gateway and to a NMEA 2000 network and wiring it to power to the alarm buzzer and to the yellow CCU signal wire on the GHC 10 Mounting the CCU Mount the CCU on the boat by using the included bracket The CCU bracket has two portions the mounting portion and the securing por
28. t match the value on the GHC 10 use the arrows to adjust the value When you are finished select Done 3 Calibrate Compass Follow the directions on the GHC 10 Before you begin the compass calibration procedure drive your boat in a slow straight line and wait for the wake generated by the previous step to pass When instructed turn the boat slowly clockwise taking care to make as steady and flat a turn as possible Turn slowly enough that the boat DOES NOT list a NOTE If you have a dual engine boat slowly run the port engine forward and the starboard engine in reverse to pivot on a stationary position After you successfully complete the calibration the GHC 10 displays a completion message select Done If the calibration fails select Retry to begin the process again GHP 10V Installation Instructions 13 4 Autotune Before you begin the Autotune procedure adjust the throttle so that the boat travels at a constant RPM below planing speed with enough speed to maintain responsive steering Select Begin when you are ready The boat will perform a number of zigzag motions while the Autotuning is in progress When the GHC 10 displays a completion message select Done Be sure to resume manual control of the boat when Autotuning is complete If the Autotuning fails e Increase the throttle approximately 200 RPM and select Retry to begin the process again e If it fails again continue retrying the process adding increments of 200 RPM
29. terference ae 2 Determine the correct type of screws for the mounting surface Mounting screws are included Mountin with the CCU but you may need to provide different screws or use bolts if the supplied 4 screws x3 screws are not suitable for the mounting surface ma 3 Use the mounting template provided on page 19 Be sure to orient the template with an opening at the bottom because the CCU cables must hang straight down Tape the template to the mounting location 4 Drill pilot holes at the three locations on the mounting template 5 Use screws or bolts to secure the mounting portion of the CCU bracket To secure the CCU in the CCU bracket 1 Connect the CCU cable and the NMEA 2000 drop cable to the CCU 2 Place the CCU in the mounting portion of the CCU bracket with the wires hanging straight down toward the water 3 Place the securing portion of the bracket over the ball and snap it into the mounting portion of the bracket starting with the two arms that do not have the thumbscrew 4 Make sure the cables hang straight down toward the water and connect the arm with the thumbscrew The cables must hang straight down for the CCU to accurately read your heading 5 Hand tighten the thumbscrew until the CCU is held firmly in the bracket Do not overtighten the thumbscrew lt il Cables 6 GHP 10V Installation Instructions Wiring the CCU Route the connector terminated end o
30. ting you want to configure 3 Select the setting you want to configure Category GHC 10 with the tachometer on the dashboard of your boat Tachometer Setup RPM Source This setting is not used for the GHP 10V The RPM information will be received from the Volvo autopilot gateway Tachometer Setup Planing RPM Take note of the RPM reading from the tachometer on the dashboard of your boat at the point your boat transitions from displacement to planing speed If the value does not match the value on the GHC 10 use the arrows to adjust the value Tachometer Setup Low RPM Limit Take note of the RPM reading from the tachometer on the dashboard of your boat at the lowest RPM point If the value does not match the value on the GHC 10 use the arrows to adjust the value Tachometer Setup Verify Tachometer With the engine or engines running compare the RPM readings on the Tachometer Setup High RPM Limit Take note of the RPM reading from the tachometer on the dashboard of your boat at the highest RPM point If the value does not match the value on the GHC 10 use the arrows to adjust the value Turn Fine Tuning Setup Acceleration Limiter Limit the aggressiveness of autopilot controlled turns Increase the percentage to limit the turn rate and decrease the percentage to allow higher turn rates Navigation Setup Fine Heading Adjustment Increase or decrease to fine tune the autopilot heading GHP 10V Installation Instructions a a N
31. tion Install the mounting portion on the mounting surface and secure the CCU in the bracket with the securing portion When mounting the CCU e Mount the CCU in the forward half of the boat no higher than 10 ft 3 05 m above the waterline You can mount the CCU below the waterline as long as it is not in a location where it will be submerged or exposed to wash down e Mount the CCU bracket on a vertical surface or under a horizontal surface so that the connected wires hang straight down e Do not mount the CCU near magnetic material magnets speakers and electric motors or high current wires e Mount the CCU at least 24 in 0 6 m away from movable or changing magnetic disturbances such as anchors anchor chain wiper motors and tool boxes e Use a handheld compass to verify the absence of magnetic interference If the handheld compass does not point north when you hold it in the location you want to mount the CCU then there is magnetic interference Choose another location and test again e If possible mount the CCU within 9 1 2 ft 3 m of the Autopilot Gateway If you cannot mount the CCU within 9 1 2 ft 3 m of the Autopilot Gateway use a NMEA 2000 drop cable up to 20 ft 6m long not included to extend the cable Do not connect the CCU cable to a NMEA 2000 network To mount the CCU bracket 1 Determine the best location for the CCU on your boat Use a handheld compass to be sure that the location is free of magnetic in
32. turbances such as anchors anchor chain wiper motors and tool boxes Use a handheld compass to test for magnetic interference in the area e The CCU cable connects the CCU to the Autopilot Gateway and provides 9 2 ft 3 m of cable between the CCU and the Autopilot Gateway If you cannot mount the CCU within 9 1 2 ft 3 m of the Autopilot Gateway use a NMEA 2000 drop cable up to 20 ft 6m long not included to extend the cable Do not connect the CCU cable to a NMEA 2000 network e The CCU cable connects the CCU to power to the alarm buzzer and to the yellow CCU signal wire of the GHC 10 using wires with bare ends See page 7 for wiring instructions and diagrams CCU and GHC 10 e The CCU and the GHC 10 connect to a NMEA 2000 network using dedicated NMEA 2000 communication ports If you do not have a NMEA 2000 network on your boat the equipment necessary to build one is provided For instructions on setting up the NMEA 2000 network see page 11 e You can connect an optional NMEA 2000 compatible GPS device to the NMEA 2000 network to use waypoint and route data with the GHP 10 GHC 10 e Wire the GHC 10 to the battery of the boat and to the yellow CCU signal wire of the Autopilot Gateway cable e If you do not have an optional NMEA 2000 compatible GPS device you can wire an optional NMEA 0183 compatible GPS device to the power data cable of the GHC 10 instead see page 12 4 GHP 10V Installation Instructions Yellow CCU
33. ush mount the GHC 10 3 Use the 3 7 s2in 90 mm hole saw to cut the mounting surface along the line indicated on the flush mount template Use a file and sandpaper to refine the size of the cutout if needed 4 Place the GHC 10 into the cutout to confirm that the four mounting holes are correct after refining the cutout If not mark the correct locations of the four mounting holes Remove the GHC 10 from the cutout 5 Drill the four t s in 3 2 mm pilot holes NOTE If you are mounting the GHC 10 in fiberglass it is recommended to use a countersink bit to drill a clearance counterbore through only the top gel coat layer This will help to avoid any cracking in the gel coat layer when the screws are tightened 6 Remove the remainder of the template 7 Place the GHC 10 into the cutout 8 Securely tighten the four mounting screws through the GHC 10 into the drilled mounting holes NOTE Stainless steel screws may bind when screwed into fiberglass and overtightened Garmin recommends applying an anti galling stainless anti seize lubricant to the screws before installing them 9 Snap the mounting covers into place to install them GHC 10 m g Po NX 8 GHP 10V Installation Instructions Wiring the GHC 10 to Power and to the CCU Cable With the GHC 10 power data cable wire the GHC 10 to power and to the yellow CCU signal wire on the CCU cable Optionally you can wire the GHC 10 power data cable to a NMEA
34. you can connect the GHC 10 to a NMEA 2000 or NMEA 0183 compatible GPS device to use waypoint and route data Mounting the GHC 10 Flush mount the GHC 10 in the dashboard near the helm When you select an installation location for the GHC 10 choose a location with the following characteristics e Provides optimal viewing as you operate your vessel e Allows easy access to the keypad on the GHC 10 e Is strong enough to support the weight of the GHC 10 and protect it from excessive vibration or shock e Allows room for the routing and connection of the cables for power and data There should be at least a 3 inch 8 cm clearance behind the case e Is atleast 9 2 in 0 24 m from a magnetic compass to avoid interference e Is in an area that is not exposed to extreme temperature conditions CAUTION The temperature range for the GHC 10 is from 5 F to 158 F from 15 C to 70 C Extended exposure to temperatures outside of this range in storage or operating conditions may cause failure of the LCD screen or other components This type of failure and related consequences are not covered by the limited warranty To flush mount the GHC 10 1 A flush mount template is included in the product box Trim the template and ensure it will fit in the location at which you want to flush mount the GHC 10 2 The flush mount template has adhesive on the back Remove the protective liner and apply the template to the location where you want to fl
Download Pdf Manuals
Related Search