Garmin echoMAP 71sv Installation Instructions
Contents
1. 4 Wait several minutes while the software update process completes The device returns to normal operation after the software update process is complete 5 Remove the memory card NOTE If the memory card is removed before the device restarts fully the software update is not complete Specifications Device Specification Measurement echoMAP 70 Dimensions W x H x D 25 x 13 9 x 5 1 cm 9 8 x 5 5 x 2 in Display size W x H 15 2 x 9 1 cm 6 0 x 3 6 in Weight 0 77 kg 1 7 Ibs Power input From 10 to 18 Vdc Max power usage 20 W Compass safe distance 65 cm 25 6 in echoMAP 90 Dimensions W x H x D 28 8 x 16 3 x 5 1 cm 11 3 x 6 4 x 2 in Display size W x H 19 8 x 11 2 cm 4 4 x 7 8 in Weight 1 kg 2 3 Ibs Power input From 10 to 20 Vdc Max power usage 11W Compass safe distance 55 cm 21 7 in All Models Temperature range From 15 to 55 C from 5 to 131 F Material Polycarbonate plastic Water rating IEC 60529 IPX7 Transmit power RMS 500 W Maximum depth 701 m 2300 ft at 77 kHz Frequencies e Traditional 50 77 or 200 kHz e DownViu 260 or 455 kHz The device withstands incidental exposure to water of up to 1m for up to 30 min For more information go to www garmin com waterrating Dependent upon transducer rating and depth Maximum depth dependent upon transducer water salini2. counterbore through only the top gel coat layer This will help to avoid any cracking in the gel coat layer when the screws are tightened Stainless steel screws may bind when screwed into fiberglass and overtightened Garmin recommends applying an anti seize lubricant to the screws before installing them 1 Select the mounting hardware appropriate for your mounting surface and for the bail mount bracket 2 Using the bail mount bracket as a template mark the pilot holes through the screw holes 3 Using a drill bit appropriate for the mounting hardware drill the four pilot holes 4 Using the selected mounting hardware secure the bail mount bracket to the mounting surface 5 Place the device into the cradle Install the bail mount knobs on the sides of the device 7 Place the cradle in the bail mount bracket and tighten the bail mount knobs o Flush Mounting the Device Be careful when cutting the hole to flush mount the device There is only a small amount of clearance between the case and the mounting holes and cutting the hole too large could compromise the stability of the device after it is mounted Using a metal pry tool such as a screwdriver can damage the trim caps and the device Use a plastic pry tool when possible 190 01835 02_0B A flush mount template and hardware can be used to mount the device in your dashboard 1 Trim the template and make sure it fits in
3. A GARMIN echoMAP 70 90 Series Installation Instructions To obtain the best performance and to avoid damage to your boat install the device according to these instructions Read all installation instructions before proceeding with the installation If you experience difficulty during the installation contact Garmin Product Support Important Safety Information See the Important Safety and Product Information guide in the product box for product warnings and other important information When connecting the power cable do not remove the in line fuse holder To prevent the possibility of injury or product damage caused by fire or overheating the appropriate fuse must be in place as indicated in the product specifications In addition connecting the power cable without the appropriate fuse in place voids the product warranty Always wear safety goggles ear protection and a dust mask when drilling cutting or sanding NOTICE When drilling or cutting always check what is on the opposite side of the surface To obtain the best performance and to avoid damage to your boat install the device according to these instructions Read all installation instructions before proceeding with the installation If you experience difficulty during the installation contact Garmin Product Support Registering Your Device Help us better support you by completing our online registration today Go to http my garmin co
4. d B wires NMEA 0183 Connection Diagram 96 4 Item Description 12 Vdc power source Wiring harness NMEA 0183 compliant device Garmin Wire NMEA 0183 Device Wire Item Garmin Wire Function 07o ola Function Power Red Power Ground Black Data ground Tx Blue Rx A Rx Brown Tx A Installing the Cables and Connectors Wiring to Power 1 Route the power cable from the swivel mount to the boat battery or fuse block 2 If necessary extend the wires using 82 mm 18 AWG or larger wire 3 Connect the red wire to the positive terminal on the battery or fuse block and connect the black wire to the negative terminal Connecting the Device to a Transducer NOTE The device goes into simulator mode if the connection is not secure between the device and transducer Go to www garmin com or contact your local Garmin dealer to determine the appropriate type of transducer for your needs 1 Follow the instructions provided with your transducer to correctly install it on your boat 2 Route the transducer cable to the back of your device away from sources of electrical interference 3 Connect the transducer cable to the appropriate port on your device Connecting the Cables to the Cradle The connectors on the cables are keyed to fit only in the correct ports on the device or cradle The connected cables ar
5. e held in place by a locking bracket 1 Remove the cable locking bracket from the cradle 2 Compare the divots on each cable connector to the keying on each port to determine which cable corresponds to each port 3 Securely connect each cable to a port 4 Place the locking bracket over the cables and slide the bracket down to lock the cables in place There is an audible click when the locking bracket is installed correctly Installing the Device in the Cradle If your device uses a cradle and you have connected the cables to the cradle you can quickly place the device in the cradle without plugging in any cables 1 Place the base of the device in the bottom of the cradle 2 Tilt the device toward the cradle until it fastens in place There is an audible click when the device is secured in the cradle Removing the Device from the Cradle 1 Press the release lever on the cradle until the device is released 2 Tilt the device forward and lift it out of the cradle Updating the Device Software Before you can update the software you must obtain a software update memory card or load the latest software onto a memory card 1 Turn on the chartplotter 2 After the home screen appears insert the memory card into the card slot NOTE In order for the software update instructions to appear the device must be fully booted before the card is inserted o Follow the on screen instructions
6. fore installing them on the device 14Place the device into the cradle 15Securely connect each cable to a port on the cradle 16 Place the locking bracket over the cables 17 Place the device into the cutout 18Secure the device to the mounting surface using the included screws 19 Install the trim caps by snapping them in place around the edges of the device Wiring Harness e The wiring harness connects the device to power and NMEA 0183 devices The device has one internal NMEA 0183 port that is used to connect to NMEA 0183 compliant devices If it is necessary to extend the power and ground wires you must use 82 mm 18 AWG or larger wire If it is necessary to extend the NMEA 0183 or alarm wires you must use 22 AWG 33 mm wire 2 tie Item Wire Function Wire Color NMEA 0183 internal port Rx in Brown NMEA 0183 internal port Tx out Blue Ground power and NMEA 0183 Black Power Red Connecting the Wiring Harness to Power 1 Route the wiring harness to the power source and to the device 2 Connect the red wire to the positive battery terminal and connect the black wire to the negative battery terminal NMEA 0183 Connection Considerations e The installation instructions provided with your NMEA 0183 compatible device should contain the information you need to identify the transmitting Tx and receiving Rx A an
7. m e Keep the original sales receipt or a photocopy in a safe place AEN Garmin Product Support Go to www garmin com support for in country support information In the USA call 913 397 8200 or 1 800 800 1020 In the UK call 0808 238 0000 In Europe call 44 0 870 850 1241 TODI Needed Drill and drill bits e 2 Phillips screwdriver e Jigsaw or rotary tool e File and sandpaper e Marine sealant optional Mounting Considerations The device can be mounted using the included bracket or it can be mounted flush with the dashboard using a flush mount kit may be sold separately December 2014 Printed in Taiwan Before permanently installing any part of your device you should plan the installation by determining the location of the various components e The mounting location must provide a clear view of the screen and access to the keys on the device e The mounting location must be sturdy enough to support the device and the mount e The cables must be long enough to connect the components to each other and to power e The cables can be routed under the bail mount or behind the device e To avoid interference with a magnetic compass the device should not be installed closer to a compass than the compass safe distance value listed in the product specifications Bail Mounting the Device If you are mounting the bracket on fiberglass with screws it is recommended to use a countersink bit to drill a clearance
8. the location where you want to mount the device 2 Secure the template to the selected mounting location 3 Using a 9 5 mm g in drill bit drill one or more of the holes inside the corners of the solid line on the template to prepare the mounting surface for cutting 4 Using a jigsaw or rotary cutting tool cut the mounting surface along the inside of the solid line indicated on the template 5 Place the device into the cutout to test the fit 6 If necessary use a file and sandpaper to refine the size of the hole 7 NOTE Not all devices have trim caps Using a pry tool such as a flat piece of plastic or a screwdriver carefully pry up the corners of the trim caps and slide the pry tool to the center to remove the trim caps 8 Ensure the mounting holes on the device line up with the pilot holes on the template 9 Ifthe mounting holes on the device do not line up mark the new pilot hole locations 10 Using a 3 2 mm 1 g in drill bit drill the pilot holes 11 Remove the template from the mounting surface 12 If you will not have access to the back of the device after you mount it connect all necessary cables to the device before placing it into the cutout NOTE To prevent corrosion of the metal contacts cover unused connectors with weather caps 13 Install the rubber gasket pieces on the back of the device The pieces of the rubber gasket have adhesive on the back Make sure you remove the protective liner be
9. ty bottom type and other water conditions Dependent upon echoMAP model NMEA 0183 Information Sentence Description VDM AIS VHF data link message Type You can purchase complete information about National Marine Electronics Association NMEA format and sentences from NMEA Seven Riggs Avenue Severna Park MD 21146 USA www nmea org Type Sentence Description Transmit GPAPB APB Heading or track controller autopilot sentence B GPBOD BOD Bearing origin to destination GPBWC BWC Bearing and distance to waypoint GPGGA GGA Global positioning system fix data GPGLL GLL Geographic position latitude and longitude GPGSA GSA GNSS DOP and active satellites GPGSV GSV GNSS satellites in view GPRMB RMB Recommended minimum navigation information GPRMC RMC Recommended minimum specific GNSS data GPRTE RTE Routes GPVTG VTG Course over ground and ground speed GPWPL WPL Waypoint location GPXTE XTE Cross track error PGRME E Estimated error PGRMM M Map datum PGRMZ Z Altitude SDDBT DBT Depth below transducer SDDPT DPT Depth SDMTW MTW Water temperature SDVHW VHW Water speed and heading Receive DPT Depth DBT Depth below transducer MTW Water temperature VHW Water speed and heading WPL Waypoint location DSC Digital selective calling information DSE Expanded digital selective calling HDG Heading deviation and
10. variation HDM Heading magnetic MWD Wind direction and speed MDA Meteorological composite MWV Wind speed and angle Garmin and the Garmin logo are trademarks of Garmin Ltd or its subsidiaries registered in the USA and other countries echoMAP is a trademark of Garmin Ltd or its subsidiaries These trademarks may not be used without the express permission of Garmin NMEA is a registered trademark of the National Marine Electronics Association 2014 Garmin Ltd or its subsidiaries EAL C www garmin com support
Download Pdf Manuals
Related Search