Garmin 190-0172_0B User's Manual
Contents
1. NOTE A green amber or red flash denotes how much charge is left in the dog device battery ranging from high to low Enabling the BarkLimiter Feature On the dog collar device hold the power key until the LED flashes blue Bark Odometer When you turn off the device the LED flashes red and green to report the number of times the device detected a bark since it was last turned on This can help you track your dog s barking behavior Red flash 10 barks Green flash 1 bark For example one red flash followed by four green flashes indicates the device detected 14 barks Zero flashes indicates the device detected zero barks Checking the Bark Odometer 1 Remove the device from the dog 2 Position the device so that you can see the status LED 3 Hold the power key until the status LED turns red and release 4 Count the red and green flashes Using the Light You can use the light feature on your device to verify pairing help locate your dog and provide safety for your dog at night 1 Select a dog collar device Selecting a Dog Collar Device 2 Rotate the intensity dial to L 3 Select the training key Dog Training Device Information Pro Trashbreaker Handheld Device Specifications Battery type Rechargeable replaceable lithium ion Battery life 60 hours typical use Operating temperature range From 4 to 140 F from 20 to 60 C Charging temperat2. A GARMIN Pro Trashbreaker Owner s Manual March 2014 190 01726 00 0B Printed in Taiwan All rights reserved Under the copyright laws this manual may not be copied in whole or in part without the written consent of Garmin Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements Go to www garmin com for current updates and supplemental information concerning the use of this product All rights reserved Under the copyright laws this manual may not be copied in whole or in part without the written consent of Garmin Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements Garmin and the Garmin logo are trademarks of Garmin Ltd or its subsidiaries registered in the USA and other countries BarkLimiter and Bark Odometer are trademarks of Garmin Ltd or its subsidiaries These trademarks may not be used without the express permission of Garmin Getting Started Attaching the Dog Collar Device to the Collar Strap eae 1 With the buckle facing outward insert the end of the collar See the mportant Safety and Product Information guide in the strap through the slot on the collar device product box for product warnings and other important informatio
3. ary switch connector to the device When properly installed the connector plug snaps into the port 13 Verify the gasket is not damaged and is completely seated in the groove on the front half of the device 14While ensuring the battery and rotary switch wires are not pinched hold the back plate and the device firmly together and replace all eight security screws without tightening 15 Verify the back plate and the device are aligned with no gaps 16 Tighten the screws evenly 17 Verify the gasket is not sticking out of the device o Pro Trashbreaker Dog Collar Device Components Q 6 t i 0 O O g TE el Gasket C Front enclosure Security screws Top plate Battery plate screws Battery plate 0000 Battery Replacing the Battery Assembly Before you replace the battery you must remove all dirt water and debris from the device You also need a small Phillips screwdriver and the security screwdriver included with the battery replacement kit You can purchase a replacement battery at http buy garmin com You should use only an official Garmin replacement part 1 Remove the three screws from the cover over the VHF antenna O s S GARMIN 2 Pry off the cover 3 Remove the screw securing the VHF antenna to the back plate 4 Remove the six screws from the top pla
4. e You also need a small Phillips screwdriver and the security screwdriver included with the battery replacement kit You can purchase a replacement battery at http buy garmin com You should use only an official Garmin replacement part 1 Remove the eight security screws from the back of the device 2 Lift up the back plate 3 Grip the battery connector wires close to the connector and pull the connector perpendicular to the circuit board to disconnect the battery connector from the device 4 Device Information 4 Grip the rotary switch connector wires close to the connector and pull the connector perpendicular to the circuit board to disconnect the rotary switch connector from the device 5 Remove the two screws from the battery plate Lift up the battery plate 7 Remove the old battery from the back plate noting the orientation of the battery The battery fits tightly It may be necessary to pry the battery out of the back plate using a non sharp non metal object 8 Install the new battery into the back plate with the label side up using the same orientation as the old battery The battery orientation is noted graphically inside the back plate 9 Replace the battery plate to its original position 10Replace and tighten the battery plate screws 11 With the new battery connect the battery connector to the device When properly installed the connector plug snaps into the port 12 Reconnect the rot
5. formation about optional accessories and replacement parts Registering Your Device Help us better support you by completing our online registration today Go to http my garmin com e Keep the original sales receipt or a photocopy in a safe place Device Information www garmin com support 913 397 8200 1 800 800 1020 1 866 429 9296 32 2 672 52 54 420 221 985466 420 221 985465 358 9 6937 9758 39 02 36 699699 0800 0233937 00800 4412 454 44 2380 662 915 386 4 27 92 500 34 93 275 44 97 46 7744 52020 ii gt m am i be i E s 0808 238 0000 44 0 870 8501242 43 0 820 220230 385 1 5508 272 385 1 5508 271 45 4810 5050 ai 331 55 69 33 99 52 001 855 792 7671 2 EI Ex 35 1214 447 460 NU 0861 GARMIN 427 646 Samm 27 0 11 251 9999 49 0 180 6 427646 20 ct Anruf a d deutschen Festnetz Mobilfunk max 60 ct Anruf 47 815 69 555 Garmin International Inc 1200 East 151st Street Olathe Kansas 66062 USA Garmin Europe Ltd Liberty House Hounsdown Business Park Southampton Hampshire SO40 9LR UK Garmin Corporation No 68 Zhangshu 2nd Road Xizhi Dist New Taipei City 221 Taiwan R O C 2014 Garmin Ltd or its subsidiaries
6. ld device set the intensity level to a numbered position Changing the Intensity Level 3 On the dog collar device hold the power key for about 5 seconds until the status LED changes to yellow 4 On the handheld device select a training key The dog collar device beeps when the devices have paired successfully If the device does not beep pairing has not been successful TIP If the devices did not pair successfully you should verify the batteries in both devices are fully charged and the intensity level is set to a numbered position Selecting a Dog Collar Device Before you can select and control a dog collar device you must pair the dog collar device with the handheld device Pairing a Dog Collar Device with the Handheld Device Select the color associated with a dog collar device e To select the button color move the dog collar device toggle switch up e To select the inner ring color move the toggle switch to the middle position e To select the outer ring color move the toggle switch down The training keys control the dog collar device associated with the selected color Dog Training You should research and investigate the training methods best suited for you your dog and your needs When used properly the Pro Trashbreaker training system is an effective training tool to aid your dog in reaching its full potential The use of the training system should be part of an overall training program Fitting the Colla
7. lectrical stimulation If the dog vocalizes more than once the intensity level is too high for beginning training 4 lf there is no reaction increase the intensity level by one level until the dog has a slight but recognizable reaction to the stimulation The intensity level that causes a slight but recognizable reaction is your dog s baseline level for beginning collar training You do not need to and should not apply this intensity selection test again After you begin training the dog s performance guides your intensity selection As the dog advances in training you may need to change the level depending upon the training situation Changing the Intensity Level You can select a different intensity level for each dog collar device 1 Select a dog collar device Selecting a Dog Collar Device 2 Adjust the intensity dial to increase or decrease the intensity level BarkLimiter When the dog collar device is active and properly fitted on the dog it detects and corrects barks automatically The dog collar device starts at the lowest intensity level and increases the intensity level gradually until the dog stops barking When the dog is quiet the intensity decreases over time The status LED flashes briefly when the dog collar device detects motion or corrects a bark Green amber or red Motion was detected and no correction was flash applied Blue flash A bark was detected and a correction was applied
8. mperature range up to 3 months From 4 to 95 F from 20 to 35 C Water rating Up to 1 ATM The device withstands pressure equivalent to a depth of 10 meters Checking the Battery Level Turn on the dog collar device Turning On the Dog Collar Device The status LED flashes every few seconds while the device is on The color of the status LED indicates the battery charge level Green The battery has a good charge Yellow The battery should be charged soon Red The battery is very low and should be charged immediately Flashing Red The battery is depleted and must be charged Training features are disabled Replacing the VHF Antenna in the Dog Collar Device Before you replace the VHF antenna you must remove all dirt water and debris from the device You also need a small Phillips screwdriver and a larger Phillips screwdriver 1 Remove the three screws antenna 2 Pry off the cover from the cover over the VHF T Contact your local waste disposal department to properly recycle the batteries Pro Trashbreaker Handheld Device Components Security screws Back plate Battery plate screws Gasket Battery plate Battery 0100009 Replacing the Pro Trashbreaker Handheld Device Battery Before you replace the battery you must remove all dirt water and debris from the devic
9. n Setting Up the Pro Trashbreaker System Before you can use the Pro Trashbreaker system you must set up the devices 1 Attach the dog collar device to the collar strap Attaching the Dog Collar Device to the Collar Strap 2 Charge the handheld device Charging the Handheld Device 3 Charge the dog collar device Charging the Collar 4 Turon the devices Tuming On the Dog Collar Device 2 Pull most of the collar strap through the two slots on the 5 If necessary pair the dog collar device with the handheld dog device ee a SESE Cala i ener tie Habe nee 3 Insert the end of the collar strap through the slot on the opposite side of the device Device Overviews 4 Pull the strap until it is tight across the front of the device Wrap the antenna keeper around the collar strap NOTE Do not bend the antenna sharply You should lengthen the collar strap on the side with the antenna keeper to avoid bending the antenna sharply Slide the antenna through the antenna keeper a Pro Trashbreaker Handheld Device 6 Ow Qe Charging the Handheld Device You should fully charge the battery before you use the device for the first time or whenever the battery is low Checking the Battery Level It is normal for the battery to discharge in approximately 7 to 10 weeks when the device is not in use Charging a fully depleted battery takes about 2 hours NOTE The device will not charge when it is outside the tempe
10. r on Your Dog ARCAUTION To prevent irritation from the contact points remove the collar for at least eight hours out of every 24 hour period This device is not intended for human use Do not attempt to use on any person In order to properly correct the dog the collar and device must fit the dog properly If the collar is too loose or positioned incorrectly corrections may be inconsistent This can delay or prevent successful training 1 Place the collar around the middle of the dog s neck 2 Position the device at the front of the dog s neck with the status LED facing toward the dog s chin and the contact points against the throat 3 Tighten the strap so that it is very snug around the dog s neck and fasten the buckle NOTE The collar should fit tightly and should not be able to rotate or slide on the dog s neck The dog must be able to swallow food and water normally You should observe your dog s behavior to verify the collar is not too tight Dog Training 4 Wiggle the device to work the contact points through the dog s coat NOTE The contact points must have contact with the dog s skin to be effective 5 Ifthe strap is too long cut off the excess leaving at least 3 in 8 cm to spare 6 Mark the hole used to fasten the buckle for future reference optional MURS Radio Interference If your handheld device experiences interference from another transmitter the LED flashes yellow when you pre
11. rature range of 32 to 104 F 0 to 40 C 1 Lift the weather cap GarMiy is RI TRON Intensity level and training mode dial Battery level Dog collar device toggle switch Training keys 8 9 0 Pro Trashbreaker Dog Device 2 Plug the small end of the power cable into the mini USB port on the device 3 Plug the other end of the power cable into an appropriate power source The status LED is solid red when the device is charging Power key Status LED 4 After the status LED turns solid green unplug the power cable from the device Lights Contact points Charging clip contacts 8 8 Getting Started 1 Charging the Collar To prevent corrosion thoroughly dry the contacts on the collar and the surrounding area before connecting the charging clip You should fully charge the battery before you use the device for the first time or whenever the battery is low Checking the Battery Level It is normal for the battery to discharge in approximately 7 to 10 weeks when the device is not in use Charging a fully depleted battery takes about 2 hours NOTE The device will not charge when outside the temperature range of 32 to 104 F 0 to 40 C 1 Snap the charging clip onto the device I 2 Plug the power cable into a power source The status LED is solid red when the collar is charging 3 After the status LED tu
12. rns solid green remove the charging clip from the collar Turning On the Dog Collar Device On the dog collar device hold the power key until the status LED turns green and the collar beeps to turn it on in training mode On the dog collar device hold the power key until the status LED turns blue to turn on the BarkLimiter feature BarkLimiter On the dog collar device hold the power key until the status LED turns yellow to enter pairing mode Pairing a Dog Collar Device with the Handheld Device Turning Off the Device 1 On the dog collar device hold the power key until the red LED appears 2 Release the power key The dog collar device beeps to confirm powering off NOTE If the device is powered off in BarkLimiter mode the LED flashes the number of corrected barks before powering off Checking the Bark Odometer Dog Collar Device You can use up to 9 dog collar devices with a single handheld device Each dog collar device must be paired with the handheld device before it can be used During the pairing process each dog collar device is associated with a different color on the handheld device Pairing a Dog Collar Device with the Handheld Device NOTE If your handheld device and dog collar device were included in the same package the devices are paired from the factory 1 On the handheld device move the toggle switch and select a key to choose the color associated with the dog collar device 2 On the handhe
13. ss a training key Selecting and Installing the Contact Points For best results select the correct contact points based on your dog s coat 1 Select the correct contact point length for your dog s coat type e For dogs with thicker coats use the longer contact points e For dogs with shorter coats use the shorter contact points 2 If necessary use the included wrench to remove the contact points 3 Twist the contact points into the collar 4 Tighten with the included wrench but do not overtighten When you put the collar on the dog make sure the contact points are tight against the neck Training Intensities and Methods You can use several methods to train your dog The Pro Trashbreaker system provides 6 stimulation intensity levels which increase sequentially from 1 to 6 Continuous stimulation Applies stimulation to the dog the entire time you press the training key for a maximum of 8 seconds Your stimulations should typically be much shorter than 8 seconds Tone Activates an audible tone instead of stimulation A tone can be used as either a positive or negative training cue depending on your training program Choosing the Correct Intensity Level 1 Set the intensity to the lowest level Changing the Intensity Level 2 Select a training key 3 Observe the dog for a reaction such as a head shake neck movement or just a change in expression Sometimes dogs will vocalize due to the surprise of the e
14. te and remove the top plate 5 Remove the two screws from the battery plate and remove the battery plate 6 Grip the battery connector wires close to the connector and pull the connector perpendicular to the circuit board to disconnect the battery connector from the device 7 Remove the battery The battery fits tightly It may be necessary to pry the battery out of the back plate using a non sharp non metal object 8 Install the new battery into the front enclosure with the label side of the battery facing up and the lead edge of the battery placed under the contact ledge of the device 9 Replace the battery plate and replace and tighten the two screws 10 Verify the gasket is not damaged and is completely seated in the groove 11 With the new battery connect the battery connector to the device Device Information When properly installed the connector plug snaps into the port 12Replace the front plate and replace and tighten the six screws to secure the front plate 13Replace the screw securing the VHF antenna to the back plate 14Replace the cover over the VHF antenna 15Replace the three screws on the cover 16Verify the gasket is not sticking out of the device Getting More Information You can find more information about this product on the Garmin website e Go to www garmin com outdoor Go to www garmin com learningcenter e Go to http buy garmin com or contact your Garmin dealer for in
15. ure range From 32 to 104 F from 0 to 40 C Storage temperature range From 4 to 104 F from 20 to 40 C Water rating IEC 60529 IPX7 Wireless range 4 mi 6 4 km The device withstands incidental exposure to water of up to 1 meter for up to 30 minutes Pro Trashbreaker Dog Collar Device Specifications Battery type Rechargeable replaceable lithium ion Battery life 40 hours typical use o Remove the screw securing the VHF antenna to the back plate Pull the length of the antenna from the antenna guide to remove the old antenna Loop the antenna guide around the collar strap and thread the new VHF antenna through the guide This helps to point the antenna up Replace the screw securing the VHF antenna to the back plate 7 Replace the cover over the VHF antenna 8 Replace the three screws on the cover A a o Pro Trashbreaker Battery Replacement Instructions This product contains a lithium ion battery To prevent the possibility of personal injury or product damage caused by battery exposure to extreme heat store the device out of direct sunlight Operating temperature range From 4 to 140 F from 20 to 60 C Do not use a sharp object to remove batteries Charging temperature range From 32 to 104 F from 0 to 40 C Storage temperature range up to 1 month From 4 to 122 F from 20 to 50 C Storage te
Download Pdf Manuals
Related Search