Fujitsu SATA CA97232-0014-01EN User's Manual
Contents
1. Supplement for Embedded MegaRAID SATA User s Guide gt 4 1 3 Access Privileges to ServerView RAID page 58 As for m User privilege the description is slightly modified as follows Current User s Guide ServerView RAID V2 x xx xx or previous a User privilege The User privileges are mainly used to see the status of the array controllers hard disks and logical drives To use the User privileges log in to ServerView RAID Manager with any of the user names and passwords registered with the OS With User privileges you can see the detailed information settings and status of the RAID subsystems such as the array controllers hard disks and logical drives However you cannot rebuild hard disks or modify the parameters for ServerView RAID ServerView RAID V3 x xx x or later a User privilege The User privileges are mainly used to see the status of the array controllers hard disks and logical drives To use the User privileges log in to ServerView RAID Manager with any of the user names and passwords of the user who belongs to the raid usr group With User privileges you can see the detailed information settings and status of the RAID subsystems such as the array controllers hard disks and logical drives However you cannot rebuild hard disks or modify the parameters for ServerView RAID raid usr group should be created upon necessity gt 4 2 1 Operation via Network page 60 The2. page GO sssscsssssssssssesssnsesssssssseessnsessnsesssnssssneessussssnseessneessnsessaesssneestusessaeetsneessaseerss 7 gt 4 2 5 Monitoring Event Log page 63 ssscsssssssssssssssssessusessssssssseessusessaesssssessneessuessaseesaneessasessaneessucessuseesanectieersaeeeses 7 gt 4 3 1 How to Install ServerView RAID page 65 sssssssssssssssssssssssssssssessssesssssessnsessnsessisessssesssusessasesssneceriseesseeets 7 gt 4 3 2 How to Uninstall ServerView RAID page 66 ssssssssssssssssssssssssssssssesssssseesssssseersusesssneessssneessssnseeersnseesssnses 8 gt 4 4 1 Installing HDD Check Scheduler page 68 sssssssssssssssssssssssssssessssssesssssessssssssssssnesssssnsessssneesessneeeessneeersnees 8 gt 4 4 2 Modifying HDD Check Start Time page 69 ssssssssssssssssssssssssssessssssesssssessssssessssneessssnessssnsessssnsecersneesessnees 8 gt 4 4 4 Uninstallation of HDD Check Scheduler page 71 s ssssssssssssssssssesssssessssssessssssesssssnecessssesssssessersueeessaneeessase 9 gt 4 5 1 Preparation and Precautions for using ServerView RAID Manager page 72 ssssssssssssssesssusseesssees 9 gt 4 6 3 Layout of the Tree View page 81 ssssssssssssssssssssssesssssseessssnesssssseesssneeesssssessssnseesssnseessssseessssseesssaseesrsnssestssees 9 gt 4 7 1 Viewing and Changing Array Controller Settings page 84 ssssssssssssssssssss
3. 3 13 Supplement for Embedded MegaRAID SATA User s Guide gt Product Names page 3 Include the following information when the Table Abbreviation of Product Names on P 3 of the User s Guide is referred Table Abbreviations of Product Names addition Product Names Description in the document Microsoft Windows Server 2008 Standard Windows Server 2008 Windows Microsoft Windows Server 2008 Enterprise Microsoft Windows Server 2008 Standard x64 Windows Server 2008 x64 Microsoft Windows Server 2008 Enterprise x64 Note2 Microsoft Windows Vista Business Windows Vista Microsoft Windows Vista Ultimate Microsoft Windows Vista Enterprise Note 2 When it is not particularly marked in this document it is included in Windows Server 2008 gt 2 1 SATA Setup Utility page 24 Version of expansion ROM BIOS is displayed as BIOS Version when using expansion ROM BIOS A 06 05071459R LSI Software RAID Configuration Utility Ver A 5 7 Feb 15 2008 BIOS V i A 06 05071459R Check Consistency Conf igure VD s gt 3 1 Updating Device Drives page 52 3 1 1 Creating Driver Disk The table Driver disk on page 52 is changed as follows OS Folder Name Floppy Disk Name Windows Server 2003 Drivers MegaSR W2k3 Embedded MegaRAID SATA Windows Server 2003 Drivers Disk Windows Server 2003 x64 Drivers MegaSR W2k3x64 Embedded Me
4. OS OS supporting servers with this array controller installed Web browser note Internet Explorer 6 or later Mozilla Firefox 1 0 4 or later SeaMonkey 1 0 3 or later Java note Java 2 Runtime Environment Standard Edition V1 5 0_06 or later note When in one of the environment listed bellow those software are not necessary to be installed in the server that ServerView RAID is installed However the environment that those software can be operated at the network ahead such as the server and clients PC is necessary to manage the Array When Server Core is installed at Windows Server 2008 RHELS Intel64 RHEL AS4 EM64T RHEL ES4 EM64T The table Requirements for ServerView RAID Manager on page 58 is changed as follows table Requirements for ServerView RAID Manager Category Description Network Network connection with TCP IP available Input device A mouse or other pointing device Processor Pentium 500MHz or higher 1GHz or higher recommended Memory 512MB or more 1GB or more recommended Monitor 800 x 600 or better resolution 1024 x 768 or more recommended 256 or more colors OS Windows Server 2008 Windows Vista Windows Server 2003 SP1 or later Windows XP Windows 2000 Server ServicePack4 or later Windows 2000 Professional ServicePack4 or later Web browser Internet Explorer 6 or later Java Java 2 Runtime Environment Standard Edition V1 5 0_06 or later 6 13
5. following information is added to the POINT in 4 2 1 Operation via Network on page 60 When in Windows Server 2008 firewall is enabled by default upon Windows installation Release the block on the TCP port 3173 when the ServerView RAID Manager is operated from other server or client PC connected with network gt 4 2 5 Monitoring Event Log page 63 The following information is added to the 4 2 5 Monitoring Event Log m Event log file on page 63 table Record directory of Event log files Addition For Windows 2008 C Program Files Fujitsu Siemens RAID web public For Windows 2008 x64 C Program Files x86 Fujitsu Siemens RAID web public gt 4 3 1 How to Install ServerView RAID page 65 4 3 1 How to Install ServerView RAID on page 65 is partially modified as follows Step 3 Click the Start button Run Enter the following path and click OK The Start menu is not available in the environment of ServerCore installation with under Windows Server 2008 Input the following command CD DVD drive cd RAIDTOOL SVRAID Windows install bat 7 13 Supplement for Embedded MegaRAID SATA User s Guide Step 6 Once the system is up and running create and configure a Windows user account Regarding the above the description is change as follows Current User s Guide ServerView RAID V2 x xx x or previous Users Account for User Privileges 1 Create a user account for
6. precautions on page 72 further information is added as follows Web browser cannot be operated when ServerCore is installed with Windows Server 2008 In this situation prepare the server or client PC for Windows to implement ServerView RAID Manager for management of the Array Controller when in ServerCore installation with Windows Server 2008 gt 4 6 3 Layout of the Tree View page 81 As for 4 6 3 Layout of the Tree View on page 81 include the information as follows Md PRIMERGY MEGASR G j FI LSI Embedded MegaRAID 40 G AA SATA Port 0 2 SEAGATE ST3160815AS 0 G AA SATA Port 4 GE SEAGATE ST31608154S 41 RA SATA Port RA SATA Port 3 G AA SATA Port 4 oF HL DT STDVD ROM 4 BIA SATA Port 5 SJ LogicalDrive 0 0 amp da ServerView RAID Manager Scheduler a Write snapshot B File log S amp S System log 2 LSIStoreLib Pluein Scheduler _ _ eScheduler This function is not supported It is displayed only with ServerVlew RAID V3 x xx x or later 9 13 Supplement for Embedded MegaRAID SATA User s Guide gt 4 7 1 Viewing and Changing Array Controller Settings page 84 When using ServerView RAID V3 0 14 00 or later following setting is displayed under settings tab but This function is not supported Option Default Value Initial Value Description Logical drive number for boot 0 0 Not supported Misc properties Logical drive numbe
7. the User privileges of ServerView RAID Make sure that the user account for the User privileges does not belong to the raid adm group ServerView RAID V3 x xx x or later User Account for User Privileges 1 Create a user account for the User privileges of ServerView RAID 2 Create raid usr group 3 Set the user account for the user privileges to be included in the raid usr group Make sure that the user account for the user privileges does not belong to the raid adm group gt 4 3 2 How to Uninstall ServerView RAID page 66 Follow the instruction shown below to uninstall ServerView RAID when ServerCore is installed with Windows Server 2008 1 Log on to Windows with Administrator privileges 2 Execute the following command from the command prompt wmic product where name ServerView RAID Manager call uninstall 3 Restart the system gt 4 4 1 Installing HDD Check Scheduler page 68 When in ServerCore installation with Windows Server 2008 The instruction in 4 1 1 Installing HDD Check Scheduler on page 68 is partially changed as follows Step 3 Click Start button Run Type the following file name and click OK As for the script above the start menu is not available when in ServerCore installation with Windows Server 2008 input the command as follows CD DVD drive cd RAIDTOOL HDDCS Windows install bat gt 4 4 2 Modifying HDD Check Start Time pa
8. 1EN Issued on Sep 2008 Issued by FUJITSU LIMITED e The contents of this manual may be revised without prior notice e Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual e No part of this manual may be reproduced in any form without the prior written permission of Fujitsu 13 13
9. ID D Vendor Fujitsu Siemens Computers Product LSI Embedded MegaRAID Chipset Intel ICH9R BIOS version 4 06 05071 459R BIOS build time 0507 1459 Driver name megasr Driver version 10 20 041 4 2008 gt 5 1 1 Message and Error Handling page 108 POST messages and handling of the 5 1 1 Message and Error Handling on page 108 is partially modified as follows Description Detecting a logical drive being rebuilt Message PORT x is Rebuilding State WARNING Array s in Degraded Mode XX Virtual drive s Configured Array Mode Stripe Size No Of Stripes DriveSize Status 00 RAID 1 64KB 02 XXXXXXMB Degraded Meaning The hard disc x connected to the port x is being rebuilt and the logical drive is critical degraded To start up SATA Setup Utility press the Enter key or the Ctrl M keys To pass POST press any other key Action For expansion ROM BIOS A 05 09061342R POST halts waiting for key in To pass POST and invoke OS press any key other than the Enter key or the Ctrl M keys For expantion ROM BIOS A 06 05071459R No action is required 11 13 Supplement for Embedded MegaRAID SATA User s Guide Description Not detecting hard disks and unmatched insert locations The displayed message is different according to the situation Message 1 WARNING BIOS detected configured disks w some drive s missing pls power off the system remove the drive fr
10. Supplement for Embedded MegaRAID SATA User s Guide CA97232 0014 01EN Supplement for Embedded MegaRAID SATA User s Guide cO FUJITSU 1 13 Supplement for Embedded MegaRAID SATA User s Guide Contents gt Before reading this manual sssssssssesssssseccsecssessecseessesseessessssssessessesssesseessesseessesssessesasesseessessessseesesssesseesseseresseeneeseseeeseeeees 3 gt About the change in the Array controller display name according to the driver s UPCate sssssssssserseseees 3 DS Product Names page 3 nnirnna niidina e De Soltstast cca dabiv vite caus dove a S 4 Z M2AcSATA Setup Utility page 24 ncia a aerae ie da a a a 4 gt 3 1 Updating Device Drives page 52 sssssssssssssssssssssssssesssaessssssesssssnessssansestsnseesssisesseranecessaneeersanessssinesserinesensaneeestane 4 3 1 1 Creating Driver Disk 4 Updating Drivers Windows Server 2008 Full installation 5 Updating Driver Windows Server 2008 ServerCore Installation 6 gt 4 1 2 Requirements for ServerView RAID page 57 ssscsssssssssussssssssssssessssessssssssnsessusessssesssnsessnsessssesssnecsrnseesseeets 6 gt 4 1 3 Access Privileges to ServerView RAID page 58 csssssssssssssssssesssssessssesssssseessssneeesssseessssseesssaneessssneessene 7 gt 4 2 1 Operation via Network
11. are refer to the Fujitsu PRIMERGY website http www fujitsu com global services computing server ia driver Regarding BIOS and FW contact to Fujitsu Support Office Refer to the website http www fujitsu com global contact computing PRMRGY_index htm E Trademarks Microsoft Windows and Windows Server are trademarks or registered trademarks of Microsoft Corporation in the USA and other countries Linux is a trademark or registered trademark of Linus Torvalds in the USA and other countries Red Hat and Red Hat based trademarks and logos are trademarks or registered trademarks of Red Hat Inc in the USA and other counties SUSE is a trademark of SUSE LINUX AG of Novell Inc in the USA and other countries LSI Global Array Manager GAM and MegaRAID are trademarks or registered trademarks of LSI Corporation Other product names are trademarks or registered trademarks of their respective manufacturers All other products are copyrights of their respective manufacturers Copyright FUJITSU LIMITED 2008 Screen shot s reprinted with permission from Microsoft Corporation gt About the change in the Array controller display name according to the driver s update Array controller display name is changed as follows Driver version Array controller display name V09 xx LSI Logic Embedded MegaRAID V10 xx or later LSI Embedded MegaRAID Array controller name in device manager and event log are also changed
12. ck Close to exit from the Update Driver Software window Click OK to close the Properties window If more than one array controllers are installed update all the device drivers Repeat the Step 5 to 13 until all device drivers are updated When all device drivers are updated remove the Array Controller Document amp Tool CD from CD DVD drive Restart the system 5 13 Supplement for Embedded MegaRAID SATA User s Guide Updating Driver Windows Server 2008 ServerCore Installation 1 Log on to Windows with Administrator privileges 2 Insert Array Controller Document amp Tool CD into the CD DVD drive 3 Execute the command below from the command prompt For Windows Server 2008 pnputil i a CD DVD Drive Drivers MegaSR W2K8 MegaSR INF For Windows Server 2008 x64 pnputil i a CD DVD Drive Drivers MegaSR W2K8x64 MegaSR INF 4 When device driver update is completed remove the Array Controller Document amp Tool CD from CD DVD drive 5 Restart the system gt 4 1 2 Requirements for ServerView RAID page 57 The table Requirements for ServerView RAID on page 57 is changed as follows table Requirements for ServerView RAID Category Description For Windows For Linux Hard disk 150MB or more free space in the installation 150MB or more free space under opt partition of the OS Application TCP IP SNMP service and ServerView must be installed
13. gaRAID SATA Windows Server 2003 for x64 Edition Drivers Disk Windows Server 2008 Drivers MegaSR W2k8 Windows Server 2008 Drivers Disk Windows Server 2008 x64 Drivers MegaSR W2k8x64 Windows Server 2008 for x64 Edition Drivers Disk 4 13 Supplement for Embedded MegaRAID SATA User s Guide ing Drivers Window rver 2 Fullin The update procedure for the device driver using Windows Server 2008 is as follows 1 2 10 11 12 13 14 15 16 Log on to Windows with Administrator privileges Insert the Array Controller Document amp Tool CD into a CD DVD drive Select Diagnostics gt Device Manger from Server Manger Double click Storage controllers The Controllers list appears Double click one of the below Starting with LSI Logic Embedded MegaRAID SATA Starting with LSI Embedded MegaRAID SATA Select Driver tab and click Update Driver The Update Driver Software window appears Click Browse my computer for driver software Click Let me pick from a list of device drivers on my computer Click Have Disk Click Browse button and select the file as follows For Windows Server 2008 CD DVD Drive Drivers MegaSR W2K8 MegaSR INF For Windows Server 2008 x64 CD DVD Drive Drivers MegaSR W2K8x64 MegaSR INF Click OK Confirm that the driver is displayed in the list and click Next afterwards Upon completion of the Driver update cli
14. ge 69 The instruction in 4 4 2 Modifying HDD Check Start Time on page 69 is partially changed as follows Step 2 Click Start button All Programs or Programs Accessories Command Prompt The above procedure is not needed when ServerCore is installed with Windows Server 2008 Step 4 Write down the ID value for the row with the following value in the Command Line column and Step 6 Register a new schedule By using the AT command Regarding the above procedure follow the same procedure as Windows Server 2003 when in Windows Server 2008 Refer to the instruction of Windows Server 2003 for the operation 8 13 Supplement for Embedded MegaRAID SATA User s Guide gt 4 4 4 Uninstallation of HDD Check Scheduler page 71 The procedure of the 4 4 4 Uninstallation of HDD Check Scheduler on page 71 is partially modified as follows Step 2 Click Start button All Programs or Programs Accessories Command Prompt The above procedure is no longer needed when ServerCore is installed with Windows Server 2008 Step 4 Write down the ID value for the row with the following value in the Command Line column When in Windows Server 2008 operate in the same manner as Windows 2003 Refer to the Procedure of Windows Server 2003 for implementation gt 4 5 1 Preparation and Precautions for using ServerView RAID Manager page 72 Regarding the article in e General
15. om port XX and reinsert it in another slot Press any key to continue Press any key and the following message appears If you proceed you ll lose this configuration Press any key to continue Message Message 2 Missing Drive reassigned to Port XX Or Missing Drive cannot be relocated PD s reassigned to different slot s because originally configured slot s have different PD s If you believe this is not a desired behavior pls power off the system and return the PD s to their original slots to restore the previous configuration Otherwise press any key to accept the resolved configuration Press any key to continue The hard disk connecting to the port XX was connected to the other port at the last startup The hard disk connecting to the port XX last time is not found 5 In case of message 1 The configuration information will be cleared by pressing Meaning any key to continue In case of message 2 The configuration information will be reconstructed by pressing any key to continue but consistency of configuration information is not supported Contact an office listed in the Contact Information of Start Guide Action Configuration information of the logical drives is not changed when turning off or restarting the server while this message is displayed waiting for key in 12 13 Supplement for Embedded MegaRAID SATA User s Guide Supplement for Embedded MegaRAID SATA User s Guide CA97232 0014 0
16. r for boot 0 _Edit gt 4 7 3 Setting ServerView RAID page 87 When using ServerView RAID V3 0 14 00 or later following setting is displayed under File logging Option Setting Description Text format additionally Disabled Default Additional Sveni lagot 1Exl format is recorded File logging Logging Enabled Text format additionally Disabled Log level Information File name RAIDLog xml File size 10 MB Log method Rotation Max save files 5 Edit The table of the POINT on page 89 is partially modified as follows Table At the destination of event log files For Windows Server 2003 or Windows Server 2008 C Program Files Fujitsu Siemens RAID web public For Windows Server 2003 x64 or Windows Server 2008 x64 C Program Files x86 Fujitsu Siemens RAID web public For Linux lopt fsc RAID web public 10 13 Supplement for Embedded MegaRAID SATA User s Guide gt 4 9 2 Checking Array Controller Status page 98 When using driver version of V10 xx or later As for 4 9 2 Checking Array Controller Status on page 98 include the information as follows Item Category Description BIOS version Version number of the expansion ROM BIOS for the Adapter _ array controller l BIOS build time BIOS build time of the expansion ROM BIOS for the array controller Adapter Name LSI Embedded MegaRAID 40
17. sssssssesssssessssssesssssseeessnseeenes 10 gt 4 7 3 Setting ServerView RAID page 87 sssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssessssssssssssssssesssssssssnssseseessssseey 10 gt 4 9 2 Checking Array Controller Status page 98 sssssssssssssssssssssssssesssssssssssssssssssssssssnsesesssssssssessssssssresssssessssess 11 gt 5 1 1 Message and Error Handling page 108 svssssssssssssssssssssssssssssssssssessssssssssssssssesssssssssusstssssssssssssssssessssessssseey 11 2 13 Supplement for Embedded MegaRAID SATA User s Guide gt Before reading this manual This document is to supplement the description to the Embedded MegaRAID SATA User s Guide Please also refer to the Safety Precautions and Embedded MegaRAID SATA User s Guide accompanied with Array Controller Document amp Tool CD when this document is used Note The page number in bracket indicates the page in the Current User s Guide for your reference purpose E Display Samples and figures Please note that not all display samples and figures can be shown in this document Occasionally the actual screens figures or file names may be different from their samples in this document In addition figures drawn on this document might omit cables originally connected for the convenience of the explanation E Information for PRIMERGY For the latest information on PRIMERGY update modules drivers and the softw
Download Pdf Manuals
Related Search