Fujitsu fi-4750C User's Manual
Contents
1. Place the book face down on the Documentbed 3 Issue the read command from the host system Keep the cover open for the reading operation NOTICE Do not move the book during the read operation 3 10 3 12 CHAPTER ADF DOCUMENT SPECIFICATION This chapter describes the document size and document guality required to use the ADF successfully Document Size Document Quality ADF Document Feeder Capacity Areas not to be Perforated Grounding Color Areas Double Feed Detection Condition Job Separation Sheet Document Size The following figure shows document sizes that the scanner can read using the ADF Feeding Direction ee nimam _ a 297 11 7 432 17 53 2 1 fi 4750C A3 Double Letter A8 Portrait Unit mm 4 1 Document Quality This section describes the types and weights of paper that the scanner can read and precautions in preparing documents to ensure maximal scanner functioning H Document type The recommended paper type for documents is as follows e Woodfree paper Plain paper for example the paper type specified for XEROX 4024 When using any other type of paper test feed a few sheets with the ADF to ensure the paper feeds properly before performing alarge scale reading operation Any paper can be used on the flatbed However the ground color specification must satisfy the specification described in the Grounding Color2. lt Screen 8 gt 4108 F Halftone No H1 H2 L1 L2 Halftone is Off Therefore binary reading is specified 11 Select Front Halftone by pressing lt or 2 Halftone with dither is specified Automatic separation with error diffusion is specified This parameter appears only when the IPC 4D is installed Press to confirm The scanner displays Screen 9 6 5 lt Screen 9 gt 4109 B Halftone 12 Select Back Halftone when Duplex was specified by pressing or The parameters are the same as in step 11 R Press to confirm The scanner No H17H2 L1 L2 displays Screen 10 lt Screen 10 gt 13 Select Front Document Type by pressin DH or O oe j 410 Front Doc Line Photo White level following is ON Top 3mm part of the document must be left blank L Line grounding color is drop out color Use this specification for reading line arts or texts P Photo White level following is Off i Use this specification for reading photographs Press to confirm The scanner displays Screen 11 lt Screen 11 gt 14 Select Back Document Type when Duplex was specified by pressing or The 411 Back Doc parameters are the same as in step 13 Press to confirm The scanner displays Line Photo Screen 12 lt Screen 12 Example gt 15 Confirm what you have specified If some parameter needs to change press MDF A414 0 OMILILIH1 P Next or Pre
3. The chapter describes how to install and connect the scanner Precautions Inspection Repositioning the Shipping Lock Cable Connections Mounting the Stacker Setting the SCSI ID and the SCSI Terminator Precautions This section describes precautions to follow when installing the scanner To ensure the longevity and proper functioning of your scanner do not install the scanner in the places and environments described below e Place the scanner away from electrical noise sources strong magnetic fields and air flow If the scanner is used near an air conditioner copying machine or TV set the scanner may operate incorrectly Keep the scanner out of the sun and away from heaters These environments may shorten the scanner life or cause hardware failures Do not install the scanner in a place where vibrations may occur This environment may cause hardware failures or may cause the scanner to operate incorrectly Do not install the scanner in humid dusty or damp places These environments may shorten the scanner life or cause hardware failures Do not place the scanner where liquid spills may occur Be aware of static electricity which can damage the scanner s sensitive electronic parts Be sure the flooring and the desk are made of materials that do not generate static electricity For information on the minimum required size of the installation space see Chapter 5 Specifications 2 1 Inspection T
4. the ADF completely and enable the read operation Double Feed This message is displayed when the ADF detects the Double feed error Check the document and re scan the document 1 9 H Alarm One of the following messages is displayed if an error occurs in the scanner If one of the following error messages is displayed turn the power Off and then On again If the same message is displayed contact your service representative lt Optical alarm front gt are aan Side Opti al A Toe ie im TR rf fH t Side Opi amp a tl Alarm G IP Ff f w Side ofp t ime an A 1 nrm B lt Optical alarm back gt ee ae Optical Alarm PR Back Si de Optical Alarm G Bac k S i d e Opt ea I Alarm B r 4 lt FB mechanism alarm gt TANI Mechanica Alarm NOTICE When the total number of sheets scanned by the ADF is less than 100 the message above and the message below are displayed alternately Remove the bracket Shipping Lock that holds the carrier in place Check Shipping Lock lt Motor fuse alarm gt Motor Tu S e Alarm J lt Lamp fuse alarm gt L a m pT US e Alarm 1 10 lt Image transfer alarm gt I mg Trans Alarm lt Memory alarm gt L Memor y Alarm J lt EEPROM alarm gt EEPROM A larm lt FAN alarm gt T lt IPC Board alarm gt 61 11 1 12 CHAPTER INSTALLATION AND CONNECTIONS
5. 1 Contents of the Setup mode 7 2 Conventions vi Density 6 5 Dimentions 5 2 5 3 Document bed 1 2 1 3 holding pad 1 2 1 3 Quality 4 2 Size 4 1 type 3 6 4 2 Double feed detection setting 7 4 7 5 feed error 1 9 Duplex reading mode 6 4 Enter button 1 6 Exit button 1 6 FB erasing edges 7 14 Feeding direction 4 1 Halftone processing 6 5 Heat capacity 5 2 High quality mode setting 7 15 Hopperempty 1 9 Image processing circuit 7 3 7 12 Input power 5 2 Inspection 2 2 Installation specifications 5 2 Interface connectors 1 2 1 3 Interface select 7 11 IPC mode select 7 3 7 12 preset mode setting 7 2 7 6 status display 7 2 7 10 IPC 4D option 6 7 7 12 Label A 2 2 B 2 2 Landscape orientation 6 4 LCD 1 5 LED 1 6 Light source select 7 15 Low power mode setting 7 11 Manual feed mode 3 3 start mode 1 6 Next button 1 6 Note Liability iv Offset setting 7 2 7 8 Operation status 1 8 Operator panel 1 2 1 5 Option 6 2 6 3 6 7 Pad Assembly 1 1 6 2 Paper counter 1 7 weight 4 2 Pick roller 1 4 6 1 start time setting 7 2 7 7 Plainpaper 4 2 Portrait 6 4 Power cable 1 1 2 4 consumption 5 2 inlet 1 2 1 3 2 4 switch 1 2 1 3 2 4 3 1 IN 1 Precautions 2 1 4 2 Preface v Previous button 1 6 Reading mode 6 4 face 6 4 Resetting abrasion counter 7 2 7 7 Resolution 6 4 Scanner 1 1 SCSI ID setting 7 10 SCSI terminator setting 7 10 Select interface 7 11 IPC mode 7 12 lig
6. Option IPC 4D Option Consumables The following table lists consumables used for the scanner Be sure to keep some consumables in stock The customer is responsible for changing these items periodically in accordance with the guidelines given below and in the Cleaning and Maintenance manual If they are not changed as recommended the scanner may not function properly The abrasion counter can be used to check the total number of documents scanned since the last replacement s Name Specification Remarks Pad ASY PA03951 0151 Up to 100 000 sheets or one year Up to 200 000 sheets or one year Pick rollers PA03951 0153 Two rollers are included ZZ NOTICE Refer to the Cleaning and Maintenance guide for replacing the consumables CAUTION Certain paper types or conditions might reduce the life of consumables 6 1 Options The following table lists options available for the scanner Contact your Fujitsu sales agent for more information Name P N Remarks Video Interface Board Option CA02956 2391 IPC 4D CA02919 0521 Image Processing Circuit One per unit Video Interface Option H How to Install the Video Interface Option Board Q Loosen the two screws to remove the plate 1 BEL Ss LAN gt 7 CAUTION Turn Off the power before removing the Third Party slot plate Insert the board along the rails of the third party slot Make sure
7. Press Next or Previous and let the scanner display Screen 50 2 Screen 50 displays the IPC option installed and the total image memory installed 3 Press to return 11 SCSI ID Setting 1 Press Next or Previous and let the scanner display Screen 51 2 At Screen 51 press or to select SCSI ID Then press to activate the setting 3 Press to return 12 SCSI Terminator Setting 1 Press Next or Previous and let the scanner display Screen 52 2 At Screen 52 press or to select Terminator Then press to activate the setting 3 Press to return 7 10 lt Screen 50 gt An example 110 IPC IPC 4D lt Screen 50 1 gt 110 IPC No IPC 4D lt Screen 51 gt 111 SCSI ID 0 1 2 3 4 5 6 7 lt Screen 52 gt 112 Terminator On Of f 13 Low Power Mode Setting lt Screen 53 gt 1 Press Next or Previous and let the scanner display Screen 53 113 Power Save 10 15 20min 2 At Screen 53 press or to select the time duration A minimum of 5 min to the maximum of 60 minutes can be selected Then press to activate the setting ZZ NOTICE The default time recommended by the EnerGYSTAR program is 15 minutes The default for the fi 4750C scanner is 15 minutes as recommended 3 Press to return 14 Select Interface lt Screen 54 gt 1 Press Next or Previous and let
8. Screen 57 2 4 At Screen 57 2 press or to change the top setting The value changes in 1 mm units Then press to activate the setting The scanner displays Screen 57 3 5 At Screen 57 3 press O or to change the bottom setting With Up the area is set upward from the bottom edge of the image With Down the area is set downward from the bottom edge of the image The value changes in 1 mm units Then press to activate the setting The scanner displays Screen 57 4 6 At Screen 57 4 press O or to change the left setting The value changes in 1 mm units Then press to activate the setting The scanner displays Screen 57 5 7 AtScreen 57 5 press or to change the top setting The value changes in 1 mm units Then press to activate the setting The scanner displays the next setup item lt Screen 57 gt 117 ADF EdgeERS Change No Yes lt Screen 57 1 gt Pat lh Deraul ig No Yes lt Screen 57 2 gt 117 2 ADF Top Top Omm lt Screen 57 3 gt 117 3 ADF Bottom Btm Omm Up lt Screen 57 4 gt 117 4 ADF Left Left Omm lt Screen 57 5 gt 117 5 ADF Right Right Omm 7 13 18 Adjust FB Erasing Edges 1 Press Next or Previous and let the scanner display Screen 58 2 At Screen 58 press or to select Yes and press Enter Then the scanner displays Screen 58 1 3 At Screen 58 1 select Ye
9. moves When the C gt button is pressed the blinking moves from 1 to 3 When the lt button is pressed the blinking moves in the opposite direction However if the setting by the host computer is valid the location of the blinking does not move when either button is pressed 1 No is blinking Paper thickness is not checked 2 Yes and 1 are blinking Paper thickness is checked However a detected double feed error is displayed on the screen only processing is continued 3 Yes and 2 Stop are blinking Paper thickness is checked When the double feed error is detected the scan processing is stopped The error is then reported to the host If you want to disable the double feed select No then press Enter Press to return L NOTICES 1 Double Feed detection might have better results when both the paper thickness and the paper length are Used 2 When the document in ADF is not the double fed document the previous document might be double fed in case the scanner stops feeding by using the double feed detection 3 Depending on the type of printing on the document a double feed may not be detected by the paper thickness 7 4 2 Setting double feed detection Paper Length lt Screen 42 gt 1 Press or and let the scanner display Screen 42 02 Length Check No Yes gt 1 2 Stop 2 Press either the or button to set double feed detection according to paper le
10. that may cause undesired operation Responsible Person Name Reza Majidansari Title Sr Director Product Support Engineering Peripherals Scanners and Software K Signature 2 Date Aale o o Doc No C9S012MDfi 4750C fe FUJITSU i f Conformi According to EN45014 According to Electromagnetic Compatibility Directive 89 336 EEC a 4 2 QUI RKOU ana FT LIMITED 27 at 114 Q Q C 4 1 L Ti ESTE declares in sole responsibility that the following product including the options or accessories Product Type I nner Model Number fi 4750C Aproval ID Number __S12050136 Referred to in this declaration conforms with the following directives and standards Electromagnetic Compatibility Directive 89 336 EEC 92 31 EEC 93 68 EEC EN55022 1998 Class B EN55024 1998 EN61000 4 2 1995 A1 EN61000 4 3 1996 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 EN61000 3 2 1995 A1 A2 EN61000 3 3 1995 EN60950 1992 A1 A2 A3 A4 AI1 The product of safety has been evaluated to EN60950 and has been confirmed to comply with all related requirements of EN60950 Importer Distributor in EU r 05 2000 L Tatsuya To Department Manager feren 1184 126 00 Quality assurance Department Printing and Imaging System Division
11. that the connector is connected securely Secure the board with two screws CAUTION Protective measures are required to prevent damage from static electricity Z NOTICE When the scanner power is turned On again the scanner automatically recognizes the video interface board 6 3 H Reading Mode Setting When the Video Interface Option is Installed This section describes the button specifications and setup details for reading modes when the scanner has the video interface option in the third party slot When the reading mode is set by the command from the host computer the following button operation is notrequired ZZ NOTICE When the video interface option is installed in the scanner the scanner automatically recognizes the board and changes the display Whenever you press Exit the scanner returns to screen M1 lt Screen M1 gt 1 Turn the power On and verify that Scanner g D Ready is displayed on the LCD XXX Ready XXX XXX lt Screen M2 gt E S 2 Press Next then the scanner displays Moda sea 0 Screen M2 a Reading Mode P 3 Press then the scanner displays Screen 1 lt Screen 1 gt 4 Select ADF or FB by pressing or then press Enter The scanner displays Screen 2 4101 Image Source ADF FB lt Screen 2 gt 5 Select Simplex or Duplex by pressing or C gt Then press Enter The scanner displays Screen 3 02 Reading face Si
12. the scanner display Screen 54 114 Interface Auto SCSI TPS ZZ NOTICE The screen 54 will appear oniy when the scanner has proper interface boards or option boards in the third party slot 2 At Screen 54 press or C gt to select the interface type Press if you want to change the setting ZZ NOTICES 1 Normally this setting does not have to be changed 2 When an appropriate board is installed in the third party slot of the scanner the scanner automatically turns off the SCSI interface activating the board in the third party slot Screen 54 can be used to forcibly change the selected interface The selected interface is then forcibly changed 3 The SCSI interface and the board installed in the third party slot cannot be used at the same time 4 The default is Auto 3 Press to return 7 11 15 Display the TPS Board ID Number lt Screen 55 gt An Example 1 Press Next or Previous and let the scanner display Screen 55 115 TPS Board Interface ID The scanner displays the ID number if the applicable board is installed L NOTICE If the Fujitsu video Interface Option board is installed properly the display shows ID 7 2 Press to return 16 Select Built In IPC 4D Image Processing lt Screen 56 gt 116 IPC Mode 1 Press Next C gt or and let the scanner display the Screen 56 Standard IPC 4D 2 At Screen 56 press lt or to select Sta
13. the scanner display Screen 59 119 Light Select R G B W 2 At Screen 59 press or to select a light source Press if you want to activate the setting ZZ NOTICES 1 The specification from the host computer has priority 2 The default is G Green 3 Press to return 20 Line Enhance Mode setting lt Screen 60 gt 1 Press Next or Previous and let the s scanner display Screen 60 120 Line Enhance On Ott 2 At Screen 60 press or to select On or Off Press if you want to activate the setting Zz NOTICE The reading speed reduces to half when On is selected 3 Press to return 7 15 7 16 GLOSSARY OF TERMS A4 size A standard paper size Paper size is 210 x 297 mm AB size A standard paper size Paper size is 148 x 210 mm A6 size A standard paper size Paper size is 105 x 148 mm A7 size A standard paper size Paper size is 74 x 105 mm A8 size A standard paper size Paper size is 53 x 74 mm Abrasion counter Counts the cumulative number of documents read to indicate when belts rollers should be replaced The number of read documents accumulates until an operator resets the counter The counter should be reset when these consumables are replaced ASCII The acronym for American Standard Code for Information Interchange ASCII is a set of 256 codes numbered 0 to 255 used to communicate information between a computer and an
14. the desk Good less than 20 cm 8 in 2 Remove the shipping lock from position A Then install the shipping lock at position B Front side Front side L T Enlarged H Shipping Lock A gt for operation gt a Bottom view Shipping Lock Position for storage position for shipment Enlarged section A Shipping Lock Position for shipment CAUTION Before moving or storing the scanner make sure that the shipping lock is set to the shipment position to prevent possible damage Before setting the shipping lock make sure that the carrier has been returned to the home position 2 3 Cable Connections This section describes how to connect the cables Connect the cables as follows H Turning the power switch Off Press the O side of the power switch to turn the power Off d P a SZ z T Power switch ON U Q 2 H Connecting the power cable Connect the power cable to the power inlet of the device and a power outlet for North America FT Power outlet 21 WS Power inlet lt lt ES S w A A for Europe 2 4 H Connecting the interface cables Connect the SCSI interface cables and secure them Back of the image scanner lt 9 Interface To the host system cables 53 Zz NOTICES 1 Factory default for the SCSI terminator is On If the scan
15. the scanner is On Indicates the scanner is reading or ready to read Check If lit this indicates that an alarm occurred Pressing the Stop button turns the Check lamp Off If it blinks at one second intervals this means that a jam or double feed has been detected If the problem is jammed paper removing the jammed paper turns off the Check lamp If the problem is double feed pressing the Stop button turns off the Check lamp If it blinks at four seconds intervals this means that cleaning the ADF is necessary 1 6 H Counter Display The scanner is provided with a counter display Paper counter X X X X X X Ready X X X gt Abrasion counter Counter Function Paper counter When the The paper counter counts the number of scanned sheets button is pressed from the start of reading until Paper Empty or an error is detected The counter is automatically reset at the start of reading The counter is used for checking the number of the sheets scanned in one batch When the C gt This counter increments each time a document is button is pressed scanned It is not initialized until the power is turned off The counter can be used for example for checking the number of sheets that have been scanned in one day Abrasion counter The abrasion counter counts the accumulated number of scanned sheets This counter increments every 10 sheets It is useful to check the cleaning cycle or the par
16. 9 2 26294 201 http www fujitsu europe com home FUJITSU NORDIC AB Kung Hans vag S 192 68 Sollentuna SWEDEN TEL 46 8 626 4500 FAX 46 8 626 4588 http www fujitsu europe com home FUJITSU LIMITED International Operations Marunouchi 1 6 1 Chiyoda ku Tokyo 100 JAPAN TEL 81 3 3216 3211 FAX 81 3 3213 7174 TLX J2283 Cable FUJITSU LIMITED TOKYO http www fujitsu co jp Note Liability READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT IF NOT USED CORRECTLY UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS While all efforts have been made to ensure the accuracy of all information in this manual FUJITSU assumes no liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual its updates or supplements whether such errors are omissions or statements resulting from negligence accidents or any other cause FUJITSU further assumes no liability arising from the application or use of any product or system described herein nor any liability for incidental or consequential damages arising from the use of this manual FUJITSU disclaims all warranties regarding the information contained herein whether expressed implied or statutory FUJITSU reserves the right to make changes to any products herein to improve reliability function or design without further notice and without obligation Preface This manual explains how to use the fi 4750C image scanne
17. Area section H Paper weight The paper weight should fall within the following ranges e 52 to 127 g m 13 9 to 34 Ib 127g m 34lb for A8 H Precautions A preliminary document feed test may be necessary to avoid unexpected errors If document slip or jam in the ADF JAM error or double feed occurs frequently read the documents manually using the flatbed The following documents may be difficult to read properly using the ADF e Paper with clips or staples Paper written on with wet ink Paper without a constant thickness like envelopes Paper with large rumples or curls See the NOTICE on the next page Paper with folds or tears Tracing paper Coated paper for example some paper used for color printing Carbon paper Paper smaller than A8 Portrait size or larger than A3 or Double Letter Materials other than paper for example clothes metal foil or OHP film Photographic paper Paper with notches on its side Non rectangular paper Very thin paper 4 2 Zz NOTICES 1 When scanning a translucent document set the density to light mode 2 Carbonless papers have a chemical composition that damages the Pad and Pick roller Therefore note the following Cleaning If mispicks occur frequently clean the Pad and Pick roller in accordance with the Cleaning and Maintenance manual Replacementofparts The life of the Pad and Pick roller may be shorter than if PPC paper documents are fed 3
18. C150 E182 02EN fi 4750C Image Scanner Operator s Guide fi 4750C Image Scanner Operator s Guide Revisions Disclaimers Edition Date published Revised contents 01 October 2000 First edition 02 November 2000 Partly changed Specification No C150 E182 02EN FCC declaration This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC warning Changes or modifications not e
19. ES Note the following when preparing the paper gt Remove paper clips and staples Flatten the staple holes O Read the following documents using the Flatbed Paper with clips or staples Paper written on with wet ink Paper of uneven thickness for example envelopes Paper with large rumples or curls Paper with folds or tears Tracing paper Coated paper Carbon paper Paper smaller than A8 portrait size or wider than A3 size Materials other than paper for example clothes sheet metal or OHP film Photographic paper Paper with perforations on the side Non rectangular paper Very thin paper Set documents on the ADF so that the curl of the leading edge does not exceed the measures shown below More than 30mm More than 30mm Feed direction Feed direction Less than C 1 Less than 1 3mm A 5mm LA X Top of the paper Read surface Read surface Top of the paper To avoid skewing do not feed docments of different widths during the same batch ADF paper chute Adjust the stacker extension to the paper size and then flip out the plate Stacker 3 6 4 Set the guides so that there is a small clearance between the document edges and the guides Load the document face down on the ADF paper chute and adjust the guides to the document width Zz NOTICES x Squeeze the guide lever to free the guides Do not load document stacks thicker than 8
20. IPC pre setting 1 Sharpen of parameters are available when IPC 4D is _ 2 Darken Character not installed j 3 Copy Quality 4 Resetting of Resets the abrasion counter abrasion counter Specifies the time from document Insertion to the start of picking User can select the most comfortable Pick start time for the job Time 0 2 to 29 8 sec Time 27 values from 1 to 1999 sec Offset H 2 to 3 mm V 2 to 3 mm Specifies the horizontal and vertical offset of the front side image when using the ADF Specifies the horizontal and vertical offset Offset of the back side image when using the H 2 to 3 mm ADF V 2 to 3 mm Offset H 2 to 3 mm V 2 to 3 mm Horizontal and vertical offset of the FB image is specified Displays whether or not the image IPE AV processing board IPC 4D is installed The SCSI ID is selectable Note that the 11 SCSI ID settin new setting is made valid after power is SCSI ID g g E 0 1 2 3 4 5 6 7 turned off and on again SCSI terminator Switches the SCSI terminator On Off On Off On setting 13 Low Power Mode Changes the default setting of the duration 5 min setting for power save to 60 min 7 2 Continued Me Selectable Description parameters Selects the interface when the scanner has Select Interface a board in the third party Slot Auto SCSI Tps 15 Display TPS Board Displays the ID number of the board which ID Number is installed in the third p
21. ITSU AUSTRALIA LIMITED Fujitsu Hause 2 Julius Avenue North Ryde N S W 2113 AUSTRALIA TEL 61 2 9776 4555 FAX 61 2 9776 4019 http www fujitsu com au FUJITSU CANADA INC 2800 Matheson Blvd East Mississauga Ontario L4W 4X5 CANADA TEL 1 905 602 5454 FAX 1 905 602 5457 http www fujitsu ca FUJITSU DEUTSCHLAND GmbH Frankfurter Ring 211 8000 Munchen 40 F R GERMANY TEL 49 89 32378 0 FAX 49 89 32378 100 http www fujitsu de FUJITSU ESPANA S A Edificio torre Europa 5 Paseo de la Castellana 95 Madrid 28046 SPAIN TEL 34 1 581 8000 FAX 34 1 581 8300 http www fujitsu europe com home FUJITSU EUROPE LTD 2 Longwalk Road Stockey Park Uxbridge Middlesex UB11 1AB U K TEL 44 81 573 4444 FAX 44 81 573 2643 http www fujitsu europe com home FUJITSU FRANCE S A Place des Etats Unis SILIC 310 94588 Rungis cedex FRANCE TEL 33 1 41 80 3880 FAX 33 1 4180 3866 http www fujitsu europe com home FUJITSU COMPUTERS SINGAPORE PTE LTD 20 Science Park Road 03 01 Tele Teck Park Singapore Science Park II Singapore 117674 Republic of Singapore TEL 65 777 6577 FAX 65 771 5669 http www fujitsu computers com sg FUJITSU HONG KONG Limited 10 F Lincoln House Taikoo Place 979 King s Road Island East Hong Kong TEL 852 827 5780 FAX 852 827 4724 TLX 62667 http www fujitsu com hk FUJITSU ITALIA S p A Via Nazario Sauro 38 20099 Sestos Giovanni MI ITALY TEL 39 2 26294 1 FAX 3
22. ODE Activatingthe SetupiMode AFE H cetee T7Tl l te FFE EEE EEE 7 1 Cone Oe SeA M ode 7 2 SITES OG A Nee RMS T GL 1 o INDEX N cnecee cn ccc cease care aa e ae E E aa Eaa AA E eE AA eA Ee eae a Eoee aE eA Aeae EEEE aae a IN 1 Q Declarations of Conformity vii viii o o I I gt gt v v m m 0 D O O I I gt gt v v 4 m m D 0 Let 81 O I gt m J h o o I I gt gt v v m m J BY eS N R 7 COMPONENTS INSTALLATION AND CONNECTIONS OPERATING INSTRUCTION DOCUMENT SPECIFICATION SCANNER SPECIFICATIONS CONSUMABLES AND OPTIONS SETUP MODE GLOSSARY OF TERMS INDEX COMPONENTS INSTALLATION AND CONNECTIONS DOCUMENT SPECIFICATION SCANNER SPECIFICATIONS SETUP MODE GLOSSARY OF TERMS CHAPTER COMPONENTS This chapter describes the components of the scanner part names operator panel arrangement and the function of parts and LED indicators After unpack ing the scanner confirm that all components have been received by checking them against the list in the first section Checking the Components Units and Assemblies Operator Panel Checking the Components These high precision components must be handled carefully Confirm that all the components shown in the following figure have been received If any component is missing please contact your sales agent Scanner Power cable Power cable for North America for Europe Man
23. The leading edge of all documents fed using the ADF should be straightened so the curl of the paper meets the specifications shown below More than More than 30 mm 30 mm Feed direction Less than Feed direction 3mm Less than 5mm Read surface Top of the paper Top of the paper Read surface 64 2 ADF Document Feeder Capacity The number of pages that can be loaded into the ADF chute depends on the paper size and the ream weight This information is shown in the following graph 100 190 b A4 Letter or smaller 80 B4 ADF chute loading 60 A3 number of pages or Double Letter 50 40 i 133 125 20 i 0 52 64 81 104 127 ADF Capacity g m Paper weight conversion table country unit J Cowes OOOO O aa wem 45 s 646 775 so 1098 135 _ us e 139 17 o a aro sa ata F Europe ow s ea 75 90 104 127 1s7 44 Areas not to be Perforated With the ADF perforations in the shaded areas may cause errors If you must read data from such a paper use the flatbed irection Bottom of paper Center of paper Areas that must not be perforated Grounding Color Areas The shaded area in the Figure below should have paper grounding color white or drop out color If not turn the white level following Off when reading Grounding color white or drop out color area Read reference Main scanning direction _ Subscanning dir
24. ading mode Only the front side of the document is read in this mode Place the documents face up at the center of the hopper table Smoothing A process that eliminates jaggies from slanted lines and curves Irregular convexities are deleted and irregular concavities filled in This is useful in OCR applications for example Temporary Error An error correctable by the operator Terminator Devices with a SCSI interface can be daisy chained A resistor that includes terminal circuits needs to be placed at both ends of a cable when devices are daisy chained If a device such as a scanner is the last device in a chain leaving an interface connector unused a Terminator theerfore must be attached to provide those terminal circits Third Party Interface Optional board provided by Fujitsu or interface board provided by a third party can be installed and used Time out limit This is the time the scanner waits for next document insertion after the last document feeding The scanner returns Paper Empty when no document is set after time out limit CC TPS Third Party Slot GL5 GL 6 Abrasion counter 1 7 Activating the Setup mode 7 1 ADF 1 2 1 3 ADF erasing edges 7 13 lever 1 2 1 3 mode 1 9 paper chute 1 2 Alarm 1 10 Ambient condition 5 2 Arrangement 1 5 Assemblies 1 4 Button LED Function 1 6 Cable connection 2 4 Checking the components 1 1 Connecting the interface cable 2 5 the power cable 2 4 Consumables 6
25. arty Slot When the IPC 4D image processing board is installed in the third party Slot select this ved La IPC 4D board or the image processing circuit built in the scanner Adjusts the edge areas to be erased from 17 ADF Edge Erasing the image scanned by the automatic document feeder ADF Adjusts the edge areas to be erased from the image scanned by the flat bed FB Select light source Selects a light source in reading in unicolor R G B W Select this mode when blur of color should be prevented However the reading speed On Off reduces to half 18 FB Edge Erasing Line enhance mode This offset refers to the difference from the value adjusted by automatic offset adjustment Some restrictions apply to the detection of a double feed 7 3 1 Setting double feed detection Paper Thickness When you set the use of double feed detection you must set it as follows lt Screen 41 gt 101 Double Feed No Yes gt 1 2 Stop 1 Press or and let the scanner display Screen 41 2 AtScreen 41 Press either the or button to set the double feed detection according to the paper thickness transmitted light The paper thickness is checked using the difference between two consecutive sheets of paper fed from the ADF On this screen select whether or not to check for double feeding and select the error processing Each time either of these buttons is pressed the location of the blinking
26. ation Installation Specification Dimensions Basic Product Specification Specification Remarks Operating method ADF Duplex Flatbed 2 Image sensor CCD x2 Front Back 2 Light source LED Lamp x 2 Green Red Blue Minimum Maximum B Document Thickness 4 Document Size A8 Portrait A3 Double Letter 52 g m 14 Ib to 127 g m 34 Ib 6 Optical Resolution 400 dpi 7 Output 100 150 200 240 300 400 600 800 dpi Resolution 100 150 200 240 300 400 600 dpi o 100 150 200 240 300 400 600 dpi 8 Grayscale level internal 1024 levels 10 bits 9 Scanning White binary 50ppm 200dpi A4 Portrait Speed 35ppm 300dpi A4 Portrait mechanical Simplex 64ppm 200dpi A4 Landscape Note 2 Unicolor binary 36ppm 200dpi A4 Portrait Color 16ppm 200dpi A4 Portrait White binary 90ipm 200dpi A4 Portrait 62ipm 300dpi A4 Portrait 114ipm 200dpi A4 Landscape Unicolor binary 64ipm 200dpi A4 Portrait Color 24ipm 200dpi A4 Portrait Dither Error diffusion i 100 sheets A4 64 g m 17 Ib Note 4 10 Halftone patterns 11 Capacity of ADF 12 Compression MH MR MMR Note 5 13 Interface SCSI 2 Note 6 High Density Half 50 pin Female Note 7 Third Party Slot Notes 1 The details are described in chapter 4 2 The actual scanning speed might differ due to hos
27. d is installed zk 1 3 H Assemblies 1 4 Stacker Thumb screw Pick roller 2 Guide A ASY Pick roller 1 Operator Panel The operator panel is located on the upper right hand side of the scanner The panel consists of an LCD display 16 characters x 2 lines LEDs and buttons ee H Arrangement Operator panel Previous lt gt 2 o end To CS OS gt Start O Read lt gt O Check Next HO l 1 5 H Button LED Function Fk of the button and Fk Function Displays the next LCD screen Previous Displays the previous LCD screen Moves the cursor to the left Button Moves the cursor to the right Exit When you are entering settings on the Operator panel pressing this button returns you immediately to the Scanner Ready screen Enters the parameter currently selected by the cursor Send To Operational only when Manual start mode is set or the Read lamp lights Starts Start the reading when video interface option is used Some application software packages make use of this button Stop When the Check LED lights pressing this button releases the error status turns off Check and returns to the Scanner Ready screen Operational only during the reading operation stops the reading when the video interface option is used Also turns off the Check lamp Indicates that
28. drawing mode Selecting linedrawing mode makes threshold and contrast settings effective but prevents brightness from being set The specified threshold value determines whether black or white pixels are scanned Line drawing mode is therefore appropriate for scanning text and line art images Manual Feed mode Manual Mode Requires the operator to feed each document manually into the ADF paper chute Manual start mode lt gt automatic start mode The reading operation is activated by pressing the START button in this mode Available only when video option board is installed GL 3 Mirror image The read image is symmetrically flipped to produce a mirror image of the original detected in the main scanning direction Noise removal Isolated noise from an image appearing as black spots in white areas and voids in black areas is removed to improve image quality Operator panel A panel containing the scanner indicators and buttons The operator panel is used to control scanner operations such as loading document selecting features and changing setup options Outline extraction The boundary between black and white areas is traced and the outline extracted for closed areas PAPER JAM A warning informing the user that document is jammed in the transport unit or that transportation is disabled because the transport unit is slippery This warning also appears when a double feed is de tected Photograph mode White level follo
29. ected by the operator Call CE Error diffusion High quality halftone pseudo grayscale image production based on black and white pixel binarization A pixel s optical density and that of adjacent pixels are summed with black pixels relocated in their order of density as they relate to adjacent pixels The purpose of this technique is to minimize the average error between read and printed densities Den sity data for adjacent pixels is modified by diffusing errors on the objective pixel into several pixels which are then binarized This maintains high grayscale levels and resolution during reading while suppressing more patterns by dotted halftone images such as newspaper photographs FB In this manual FB means flat bed Filtering A correction method that improves the read quality of handwritten documents The read quality of images written in pencil or ball pointed pen depends on the reflective light characteristics of the specific ink or lead used Dropped pixels may produce outlines gaps or thin barely connected lines due to uneven optical density Filtering detects areas lighter than their surroundings and increases their density to improve image clarity Front side reading Front side scanning Refers to reading the front side of the document specifically in Duplex reading mode Halftone processing Any method used to reproduce a photograph which includes a shade as an image composed of dots namely a binary image Dither
30. ection Read surface Unit mm Grounding color area 4 6 Double Feed Detection Condition When the double feed sensor is used the thickness or the combination of the thickness and the length of the document is subject to the following specifications Thickness 0 065 mm to 0 15 mm Paper length accuracy 1 or less Any black print at the center of the leading edge of the paper is not allowed 10 mm x 10 mm No binding holes are allowed within 35 mm of the middle halfway point along the center of the paper Printing duty 12 or less The deviation of the amount of transparent light on the base color area should be less than 10 ZZ NOTICE Certain paper types or a certain condition of paper result in lower detection rates in terms of double feed detection Gn Q E GM 35 mm 10 mm No printing allowed Paper feeding direction No binding holes allowed 47 Job Separation Sheet 1 Shape The following shows the typical format of the job separation sheet 15 Top of paper 15 Reading direction Bottom of paper Center of paper Job separation sheet 2 Paper conditions The paper conditions are the same as the specification described before But the paper width must be A4 or larger 210 mm or larger in width L 4 8 CHAPTER SCANNER SPECIFICATIONS This chapter describes the basic product specifications installation specifica tions and dimensions Basic Product Specific
31. his section describes how to check the labels Position of two labels Label A Sn 7 Label B Label A Example your actual label may differ Indicates regulations and standards to which this scanner conforms Fa 1 8 0 74 M 14 Tested To Comply K 9 With FCC Standards Gu FELEI FOR HOWE OR OFFICE USE rve This Class B digital apparatus complies with Canadian ICES H3 Cet appareil num rique de la classe B est conforme Ja norme NUB 003 du Canada Se Label B Example your actual label may differ Indicates product information as follows Model name MODEL fi 4750C Specification number PARTNO CAO02956 2352 2 N Serial number SER NO 000001 rn eee il MGH Weight 22 Kg i 4750C MADE IN JAPAN t t EEE F 2 3 F EEE 2 2 Repositioning the Shipping Lock To keep the scanner from being damaged during shipping the carrier unit is fixed with a Shipping Lock After placing the carrier unit where it will be installed change the position of this Shipping Lock as explainedbelow Place the image scanner on the edge of the desktop so that the left side of the scanner where the ADF is attached extends from the desktop Do not set the image scanner upside down or on its side CAUTION Do not let the scanner hang more than 20 cm 8 in over the edge of
32. ht source 7 15 Setting double feed detection paper thickness 7 4 paperlength 7 5 high quality mode 7 15 IPC preset mode 7 6 low power mode 7 11 Offset 7 8 pick start time 7 7 SCSIID 7 10 SCSI terminator 7 10 time out limit 7 8 Setup mode 7 1 7 2 Shipping lock 2 3 Simplex 6 4 Size 6 4 Specifications 5 1 5 2 Stacker 1 2 1 4 2 6 Start button 1 5 1 6 Stop button 1 5 1 6 Temporary error 1 9 Third party slot 1 2 1 3 Time out limit setting 7 8 TPS board ID number display 7 12 Turning the power on 3 1 the power off 2 4 Units 1 2 Units and Assemblies 1 2 W Weight 5 2 IN 2 O Left Arrow Key button 1 6 Right Arrow Key button 1 6 lt Next button 1 6 lt gt Previous button 1 6 Send To button 1 6 Start button 1 6 Stop button 1 6 Enter button 1 6 Exit button 1 6 o FUJITSU Declaration of Conformity Responsible Party FUJITSU COMPUTER PRODUCTS OF AMERICA INC Address 2904 ORCHARD PARKWAY SAN JOSE CA 95134 2009 U S A Phone Number 408 432 6333 Fax Number 408 894 1709 Hereby declares that the product Product Name Image Scanner 11 4750C Revision AO Conforms to the following specifications Supplementary Information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference
33. in Manual Feed mode lt Screen M1 gt XXX Ready XXX XXX lt Screen M2 gt Mode Select O fl Reading Mode lt Screen M3 gt Mode Select 1 M Manual Feed lt Screen M4 gt MO 1 No Yes Manual Feed lt Screen M1 gt XXX Ready XXXXXX Manual Loading Documents on the ADF Val NOTICE Be sure to change the position of the shipping lock according to the Installation and Connection procedure before operation ADF ADF paper chute Guide 1 Guide lever ADF lever gt Stacker Lift up the ADF paper chute and lock the bar in its operating position Operating position Bar Fan the sheets before setting a stack of Document documents on the ADF paper chute For details see the next page e Place the documents face down with the top to the left as shown in A The long side is the top for landscape mode and the short side is the top for portrait mode e Holding both ends with both hands lift the documents e Hold the documents tightly with your left hand and bend them as shown in B Grip the documents tightly with your right hand loosen the grip of your left hand and straighten as shown in C s Even up the feed edge of the batch of paper as shown in D S A For portrait mode B Z NOTICE Reduce the batch size of the documents if double feed or mispick occurs 3 5 ZZ NOTIC
34. ing IPC pre set mode When you set the use of the IPC pre set mode you must set it as follows 1 Press Next or Previous and let the scanner display Screen 43 lt Screen 43 gt 2 At Screen 43 press or to select the pre Setting and press to activate the 103 IPC Pre Set pre setting Then the scanner displays No Screen 43 1 L NOTICES The following IPC pre settings can be selected when IPC 4D is installed Preset 1 Captures texts printed on the colored background Preset 2 Produces an image with good contrast Preset 3 OCR Smoothing Preset 4 Image Smoothing Preset 5 Dither The following built in IPC pre settings can be selected even though IPC 4D is not installed e Sharpen e Darken Character e Copy Quality lt Screen 43 1 gt 3 AtScreen 43 1 select Yes or No Note that when you select Yes the IPC setting 103 1 Use IPC from the Host computer is ignored If you 9 select No the IPC setting will be changed Preset Yes No according to the host setting Finally press Zz NOTICE When you select the Copy Quality select the scanner and printer settings carefully to get the best quality 7 6 4 Reset of the abrasion counter When you reset the abrasion counter you must set it as follows 1 Press Next or Previous and let the scanner display Screen 44 lt Screen 44 gt 2 AtScreen 44 i If you want to reset the abrasio
35. ing and error diffusion processing are examples of halftone processing GL 2 Hexadecimal A base 16 numbering system also commonly referred to as hex numbers Since a base 16 system requires 16 digits numbers 0 through 9 and letters A through F are used It is convenient to express binary numbers in hexadecimal because fewer digits are required Image emphasis Density is decreased for lighter but not completely white areas adjacent to black areas Weakening this emphasis eliminates spot noise or produces softened images Image processing An image is read with specified parameters Interface The connection that allows communication from one part of a system to another For example electrical signals are transferred between the computer and scanner over an interface cable Inversion Reverse image reading In reverse image reading data is changed from black to white and vice versa IPC preset mode While reading binary images it is necessary to set the scanner according to the quality of the sheet to be read In this mode these settings can be performed in advance by corresponding each setting to a pattern number IPC 4D Image processing option of this scanner IRAS Initialization of the hardware Landscape orientation A document is transported and read with the long side vertical to the moving direction Letter size A standard paper size used in the U S A and other countries Paper size is 8 1 2 x 11 inches Line
36. is set 7 Press Exit to return to the Scanner Ready screen if you don t need to change the SCSI terminator LZ NOTICE If no other device is using the same SCSI ID the scanner ID does not have to be changed Val NOTICE The new ID does not take effect until the system power is turned On again 8 Press Next O then the scanner displays Terminator on the upper line of the LCD 4 oo Select On or Off by pressing or then press Enter Val NOTICE The scanner includes a SCSI terminator that can be turned On and Off from the operator panel of the scanner The factory default is On 9 Press Exit to return to the Scanner Ready state 27 2 8 CHAPTER OPERATING INSTRUCTION This chapter describes how to turn the power on and gives button specifica tions and reading mode settings for both ADF and Manual modes how to load documents onto the ADF and Flatbed how to load documents larger than the Document bed and how to read a page from a thick book Refer to the Cleaning and Maintenance manual for routine scanner mainte nance Turning the Power On Waking up the Scanner from the Low Power Mode Manual Feed Mode Setting Loading Documents on the ADF Loading Documents on the Flatbed Loading Documents Larger than the Document Bed Reading a Page from a Thick Book Turning the Power On This section describes how to tur
37. mm e Set the guides so that they touch the document sides O After the read command is issued from the host system and the documents are read scanned documents are expelled into the stacker for removal Guide lever Both sides 3 7 Loading Documents on the Flatbed N CAUTION Do not look directly at the light source during the read operation Scanner parts involved when loading documents Document cover Document holding pad Documentbed Q Open the document cover 2 Place the document face down and align the top left corner with the reference mark Reference mark Slowly close the Document cover Issue the read command from the host system Loading Documents Larger than the Document Bed A CAUTION Do not look directly at the light source during read operation Documentbed Document Q Open the Document cover to an angle of approximately 90 degrees and slide the cover in the direction of the arrow to remove it Place the document face down on the Document bed Issue the read command from the host system After the read operation remove the document re attach the Document cover and close it gently 03 9 Reading a Page from a Thick Book A CAUTION Do not look directly at the light source during the read operation Thick book Q Open the Document cover
38. mplex Duplex lt Screen 3 gt 6 Select Portrait or Landscape by pressing i O or Then press Enter The scanner 03 Orientation displays Screen 4 Port Land lt Screen 4 gt 7 Select Size by pressing or C gt Then press Enter The scanner displays Screen 5 04 Size A4 A3 LT LG DLT lt Screen 5 gt 8 Select Resolution by pressing or As R the cursor moves to the left 100 150 may 05 Resolution appear Then press Enter The scanner S displays Screen 6 200 240 300 400 lt Screen 6 gt 9 Select Front Density by pressing lt or As the cursor moves to the right ll 4106 Front Dens a C1 may appear Then press E Enter The scanner displays Screen 7 AT2 ME Ea BILL Density display Without IPC With IPC 4D Description option option EEE EEE Very dark EHE EHA Dark AT1 Dynamic Threshold DTC mode AT2 Simplified Dynamic Threshold IPC mode EE EE Normal H EN Light H Very light This parameter appears only when IPC 4D is installed lt Screen 7 gt 10 Select Back Density when Duplex was Selected by pressing O or C As the 4d07 Back Dens the cursor moves to the right R 77 W AT2 BEO aO BOO may appear Then press Enter The scanner displays Screen 8
39. n counter 104 Abrasion CNT select Yes through lt or C gt button and XXXXXX Reset No press Enter Go to procedure 3 If you do not want to reset the abrasion counter select No and press Enter Finally press to return lt Screen 44 1 gt 3 AtScreen 44 1 If you want to reset the abrasion counter 104 1 Reset Now select Yes and press Enter If you do not No Yes want to reset it select No and press Enter Press to return 5 Setting the pick start time When you set the pick start time you must set it as follows 1 Press Next or Previous and let the scanner display Screen 45 lt Screen 45 gt 2 At Screen 45 press to increase the Pick start time or press lt to decrease the Pick 105 Pick start start time Then press to activate the setting Finally press Exit to return 1 0 Sec 7 7 6 Setting the time out limit 1 Press Next or Previous and let the scanner display Screen 46 lt Screen 46 gt 2 At Screen 46 press to increase the number or press lt to decrease the time out 06 Time out limit Then press to activate the Z setting 30 Sec Zz NOTICE Default is 30 seconds 3 Press to return 7 ADF Front Offset Setting ADF Back Offset Setting 9 Flatbed Offset Setting o 1 Press Next or Previous and let the 07 ADF F Offset scanner display the following han 9 No yY e Fro
40. n the power On Press the I side of the power switch The power turns On and the green Power lamp at the operator panel lights d A Z Power Off Power On 3 X Power switch 3 1 Waking up the Scanner from the Low Power Mode This section describes how to wake up the scanner from the Low Power Mode To wake up the Scanner simply press a button set the papers on the ADF or send a command to scan from the host computer ZZ NOTICE As an EnerGYSTAR partner Fujitsu Limited declares that this scanner meets the ENERGYSTAR guidelines for energy efficiency 3 2 Manual Feed Mode Setting In this mode the scanner waits for some predetermined time before issuing a Paper Empty message after all documents are read This predetermined time time out limit is specified in the Setup mode Therefore you can set the next documents on the ADF chute without interrupting the reading operation The procedures for setting the manual feed mode are as follows 1 Turn the power On and verify that Scanner Ready is displayed on the LCD Press then the scanner displays Screen M2 Press then the scanner displays Screen M3 Press then the scanner displays Screen M4 Select Yes by pressing C gt Then press Enter Press to return to the Scanner Ready screen Note that Manual Feed is shown on the LCD This means that the scanner is
41. nd AssembliesT TT TT AE e R E EE E E 1 2 Operator Panel eee T 1 5 Q CHAPTER 2 INSTALLATION AND CONNECTIONS PeH IOT 2 1 IEO 2 2 Iaeiei TG Tele HG EE E ET TTE oeio aa 2 3 Gable Connectonss eY 2 4 MountingtheStacker F UT TT TT 2 6 Setting the SCAD Ene iie SSS TAMNEI nenuorama 2 7 Q CHAPTER3 OPERATING INSTRUCTION OEE ERONEN eeaeee U UT E H o E E E 3 1 Waking up the Scanner from the Low Power Mode aaaaaaaaaaasaaas aaansvaaaannaaa 3 2 Manualleed MOde Sea 3 3 Loading Documents on Me ADP ccnnsonnanananennnannaancanoannonnanacanonnnsnncaccansansanarenanssancann 3 4 Loading Documents on the Flatbed 3 a TTT 3 8 Loading Documents Larger than the Document Bed 2 2 aaaa2aaaadvsss arnar 3 9 Reading Page rom a Thick BOOTS eenaa a 3 10 Q CHAPTER 4 ADF DOCUMENT SPECIFICATION DocumentSzess ttt K te tec eee ee eg tee ee ee a se nec nen eee eters 4 1 BocumentQUalv s TT 4 2 ADRiDocument Reeder Gapacity recente TT A renee 4 4 Areassnot tobe Rerlorate O eaaa a a a A E cece lt ceneer cee E er torn ea 4 5 Grounding GTGT T T 4 6 Double Feed betectioniConditon HFEEYA AE YY TTE 4 7 elote o EIEEE e e e E 4 8 Q CHAPTER5 SCANNER SPECIFICATIONS Baal SG 5 1 InStallatiomeSpPeciticationeecessccrsese III 5 2 DIMENSIONS ieee cece cee E E cane cae eceds E E etee 5 3 Q CHAPTER6 CONSUMABLES AND OPTIONS GONSUMADISS Beene yas ae ay date Setter Penne E 6 1 IRO TS 6 2 ATs Gl G EE TIG 6 3 IIS DIK eae 6 7 Q CHAPTER 7 SETUP M
42. ndard or IPC4D When Standard is selected the scanner uses its built in image processing On the other hand the scanner selects the image processing of the IPC 4D when the IPC 4D is installed and selected ZZ NOTICE The factory default is Standard ZZ NOTICE fi 4750C has built in Image Processing The following image processing is supported both by the fi 4750C and the IPC 4D As a default the scanner built in functions are enabled By setting On using the Operator Panel the IPC 4D image processing overrides the built in functions Image Processing IPC 4D fi 4750C 1 Emphasis Smoothing 5 x 5 matrix 3 x 3 matrix 2 Outline Pre threshold Laplacian Laplacian 3 Simplified Dynamic Threshold IPC 2 like SDTC 3 x 3 max min The IPC 4D support of those functions is intended for compatibility with the IPC 3 3D except for image quality The matrix size used in the IPC 4D is larger than the one in the fi 4750C The fi 4750C Built in Dynamic Threshold is a new algorithm 7 12 17 Adjust ADF Erasing Edges 1 Press Next or Previous and let the scanner display Screen 57 2 At Screen 57 press or to select Yes and press Enter Then the scanner displays Screen 57 1 3 At Screen 57 1 select Yes to return the settings to the factory default or select No to make new settings as shown below Then press Enter The scanner displays
43. ner is in the middle of the daisy chain or of two devices turn the scanner termination Off via the operator panel 2 The factory default for the SCSI ID is 5 lf the ID of the scanner is the same as the other device change the ID via the operator panel or change the ID of the other device 2 5 Mounting the Stacker Mount the stacker using the following procedure 1 Mount the stacker Hook the pins on the stacker to the claws on the image scanner Stacker Pin inside 2 6 Setting the SCSI ID and the SCSI Terminator The default of the SCSI ID is 5 The SCSI ID is set by using the Setup mode of the operator panel The procedure to change the SCSI ID is as follows 1 Turn the power On by pressing the I side of the power switch Read gy gt see Figure 1 1 The scanner displays Scanner Ready on the lower line of the LCD 2 Then press the Next gt button The scanner displays Mode select 1 D lt 3 Then press the Next lt gt button twice The scanner displays S Mode select 2 meaning that the setup mode is ready d Then press the Enter button several times The scanner displays the following lo 5 Press the Next button c several times then the scanner ay displays SCSI ID on the upper line of the LCD 6 Select the wished SCSI ID by pressing the or C button and press Enter the SCSI ID
44. ngth The paper length is checked using the difference between two consecutive sheets of paper fed from the ADF Each time either of these buttons is pressed the location of the blinking moves When the button is pressed the blinking moves from 1 to 3 When the lt button is pressed the blinking moves in the opposite direction However if the setting by the host computer is valid the location of the blinking does not move when either button is pressed 1 No is blinking Paper length is not checked 2 Yes and 1 are blinking Paper length is checked However a detected double feed error is displayed only on the screen processing is continued 3 Yes and 2 Stop are blinking Paper length is checked When the double feed error is detected the scan processing is stopped The error is then reported to the host If you want to disable the double feed select No then press Enter Press to return After pressing Enter the scanner displays the screen 42 1 lt Screen 42 1 gt 102 1 Length 3 Press either the or button to set double feed detection paper length When the button is pressed the blinking moves from 1 to 3 When the lt button is pressed the se tae blinking moves in the opposite direction 1 The 10 is blinking Threshold is 10mm 2 The 15 is blinking Threshold is 15mm 3 The 20 is blinking Threshold is 20mm 7 5 3 Sett
45. ns of the IPC 4D refer to the supplied manual 6 7 6 8 CHAPTER SETUP MODE This chapter describes the setup mode of the scanner Activating the Setup Mode Contents of the Setup Mode Activating the Setup Mode This section describes how to activate the setup mode lt Screen M1 gt 1 Turn the power On Then the scanner displays Scanner Ready on the LCD XXX Ready XXX XXX lt Screen M2 gt 2 Ifthe scanner does not have a video interface option go to the procedure step 3 Mode Select 0 Press then the scanner with the video 4 Reading Mode interface option displays Screen M2 lt Screen M3 gt Mode Select 1 M Manual Feed 3 Press then the scanner displays Screen M3 lt Screen M4 gt 4 Press then the scanner displays Screen M4 Mode Select 2 Setup Mode 5 Press Enter Now the scanner is at Screen 41 page 7 4 in Setup mode ZZ NOTICE Any time you press Exit you can return to the Scanner Ready screen 7 1 Contents of the Setup Mode This section describes the contents of the setup mode Specifies the double feed detection Double feed is detected by checking the document length and or paper thickness Specifies the document length to enable alL double feed detection sets the document Toleranca No 10 15 20 mm No 10 15 20mm length Document Scanner automatically sets the No recommended reading parameters 3 sets i
46. nt Offset by ADF Screen 47 S Pan gt ECE e Back Offset by ADF Screen 48 e Offset of the Flatbed Screen 49 ADF B Offset 2 At Screen 47 48 or 49 select Yes by pressing the or button then press Change No Yes Enter The scanner displays Screen A X ges 7 8 or 9 109 FB Offset Change No Yes 3 At Screen A if you want to let the offset OX 1 Return to default return to default select Yes otherwise No No Y then press Enter The scanner displays g SE Screen B 7 8 lt Screen B Example of ADF Front Offset gt 4 At Screen B press to increase the offset or press lt to decrease offset The increment or decrement is 0 5 mm H 0 0mm Left 107 2 Front H lt Screen B Example of ADF Back Offset gt 08 2 Back H H 0 O0mm Left Then press to activate the setting The scanner displays Screen C lt Screen B Example of FB Offset gt 109 2 FB H H 0 0mm Left lt Screen C Example of ADF Front Offset gt 5 At Screen C press to increase the offset or press lt to decrease the offset Then 07 3 Front V press to activate the setting The a scanner displays the next item of the setup V 0 0mm Up mode lt Screen C Example of ADF Back Offset gt 108 3 Back V V 0 0mm Up lt Screen C Example of FB Offset gt 109 3 FB V V 0 0mm Up 7 9 10 IPC Status Display 1
47. other device such as a scanner Automatic separation An image processing method in which the scanner automatically detects difference between text and photos and chooses the threshold accordingly Automatic separation allows the scanner to switch between line mode and half tone mode in one pass Automatic start mode lt gt manual start mode In this mode the reading operation is activated only by issuing the the START command Backside reading Back side scanning Refers to reading the backside of the document specifically in Duplex reading mode Bit The smallest unit of information in computer memory A bit is a single digit either a 1 or a 0 in the binary numbering system Eight bits equal one byte Density In this manual refers to a measurement of the depth of the display Dither Technique for producing halftone images by representing the entire grayscale with only two pixel levels black and white GL 1 Double feed detection A scanner function which detects the accidental feeding of multiple sheets by the ADF unit Can be turned on or off by the operator Double Letter Size A standard paper size used in the U S A and othe countries Paper size is 11 x 17 inches dpi Dots per inch Dropout color A color which is used in the document but does not appear in the read image Duplex reading mode A reading mode in which both sides of the document are read Equipment Error An error that cannot be corr
48. r This manual contains chapters on the following topics COMPONENTS INSTALLATION AND CONNECTIONS OPERATING INSTRUCTIONS ADF DOCUMENT SPECIFICATIONS SCANNER SPECFICATIONS CONSUMABLES AND OPTIONS SETUP MODE It also contains a Glossary of Terms and an Index Refer to the Cleaning and Maintenance Guide for information about the routine operation of the fi 4750C The Cleaning and Maintenance Guide contains chapters on OPERATING IN STRUCTIONS CLEANING REPLACEMENT OF PARTS ADJUSTMENT and TROUBLESHOOTING The fi 4750C is a very fast and highly functional color image scanner developed for high quality color image processing using charge coupled device CCD color image sensors This scanner features high speed duplex scanning with an auto matic document feeder ADF Conventions vi Important information that requires special attention is indicated as follows A WARNING WARNING indicates that serious personal injury may result if you do not follow a procedure correctly CAUTION CAUTION indicates that minor personal injury loss of data or damage to the scanner may result if you do not follow a procedure correctly Official Fujitsu part names are indicated with an initial capital letter as in the part name Pick roller L NOTICE A NOTICE provides how to tips or suggestions to help you perform a procedure correctly CONTENTS Q CHAPTER 1 COMPONENTS GCheckingitheGomponeis aee e I 1 1 Units a
49. s to return the settings to the factory default or select No to make new settings as shown below Then press Enter The scanner displays Screen 58 2 4 At Screen 58 2 press or C gt to change the top setting The value changes in 1 mm units Then press to activate the setting The scanner displays Screen 58 3 5 At Screen 58 3 press or to change the bottom setting With Up the area is set upward from the bottom edge of the image With Down the area is set downward from the bottom edge of the image The value changes in 1 mm units Then press to activate the setting The scanner displays Screen 58 4 6 At Screen 58 4 press or C gt to change the left setting The value changes in 1 mm units Then press to activate the setting The scanner displays Screen 58 5 7 At Screen 58 5 press or to change the top setting The value changes in 1 mm units Then press to activate the setting The scanner displays the next setup item 7 14 lt Screen 58 gt 18 FB EdgeERS Change No Yes lt Screen 58 1 gt 118 1 Default No Yes lt Screen 58 2 gt 118 2 FB Top Top Omm lt Screen 58 3 gt 118 3 FB Bottom Btm Omm Up lt Screen 58 4 gt 118 4 FB Left Left Omm lt Screen 58 5 gt 18 5 FB Right Omm Right 19 Select Light Source in Unicolor Reading lt Screen 59 gt 1 Press Next or Previous and let
50. t computers environment 3 These speeds do not contain processing time at the host computer 4 The maximum number will differ due to the paper thickness Refer to chapter 4 5 The scanning speed might be slow The usage with NO COMPRESSION is recommended 6 Both SCSI 2 and the Third Party Slot can not be used at the same time 7 The Power consumption of the boards should be as follows In the Low Power Mode Less than 0 35 A With IPC 4D option Less than 1 5 A Without IPC 4D option Less than 3 0A 5 1 Installation Specification The following table lists the installation specifications of the scanner snes eee Without Hopper and Stacker 696 4 521 20 5 234 9 2 100 to 127 R or 200 to 240 VAC 10 Input power Single phase 50 60 3 Hz Ambient S 5 to 35 C 20 to 60 C p 41 to 95 F 4 to 140 F Humidity 20 to 80 8 to 95 Heat capacity 110 kcal H 442 BTU H Shipping Weight kg 28 61 7 Ib condition Dimensions io SIS T N Vl LR 2 mMm st N N bei g 445 696 17 5 27 4 unit mm 5 3 5 4 CHAPTER CONSUMABLES AND OPTIONS This chapter describes the consumables and options Consumables Options Video Interface
51. ts replacement cycle How to reset it is described in Chapter 6 NOTICE When the counter value is 0 no number is displayed 1 7 H Operation status The operation status is indicated by the following messages lt Power on gt lt Reading gt lt Waiting for Start gt Only When the Video Interface Option is installed lt Cleaning request gt Warming u p Now N ow Reading The scanner displays the following screen when waiting for the Start button to be pressed S tar S W ON When the Pick roller cleaning is necessary the scanner displays the following on the upper line When the ADF glass cleaning is necessary the scanner displays the following on the LCD C k rol ler hint eh Clean the Pick roller or the ADF glass in accordance with the manual Cleaning and Maintenance lean PEREC Now Read H Temporary error lt Hopper empty gt lt Jam gt lt ADF cover open gt lt Double feed error gt Paper Empt y This message is displayed if there is no more paper on the ADF paper chute during a read operation in ADF mode Fill the ADF paper chute with paper To enable the read operation press the stop button Ere Jam This message is displayed if a document is jammed in the ADF See the Cleaning and Maintenance manual for removing jammed documents ADF Cover Open This message is displayed if the ADF is not closed completely Close
52. uals and Driver Pad ASY lt A E RX Val NOTICE The CD ROM contains Cleaning and Maintenance and this manual Units and Assemblies This section shows the exterior view and assemblies of the scanner This section also provides the name of each part and describes its functions H Units D Document cover 4 Automatic document feeder ADF 6 Stacker SS K z Power switch A R a Interface connector 12 EXT connector Power inlet fi 4750C NOTICE The shipping lock must be switched to the operating position before the scanner can be used Refer to page 2 4 1 2 Closes over and keeps in place the document to be read Document cover Document bed Holds document to be read Also called Flatbed FB Document holding pad Presses document to the Document bed Automatic document feeder Automatically feeds documents to the reading ADF position Stacker Stacks the read documents Operator panel Contains indicator panel that indicates scanner status ADF paper chute Holds the documents to be fed by the automatic pap document feeder ADF Opens closes the ADF to enable the removal of ADF lever S documents jammed in the feeder Power inlet Connects to an AC power outlet with the power cable Interface connectors Connect to the host system with interface cables EXT connector Connects to an optional inprinter 3 Third party slot A Fujitsu Video Interface Option Boar
53. vious to select the corresponding DBA404 0 OMNOH1 p screen and re select the parameter by pressing or and finally press Enter If all parameters are acceptable press Density to return to the Scanner Ready screen Halftone Line Art or Photo Resolution Portrait _ or Landscape Paper size Front side F or Back side B Simplex S or Duplex D 6 6 IPC 4D Option The IPC 4D option performs the image processing IPC 4D supports the following image processing Item Description Pre Filter Ball Point Pen Filter Smooth ball point pen strokes Background Removal Remove background tone and light dither Dynamic Threshold One Pass Two Pass Dynamic Threshold Adjust threshold level for binarzing to separate from background Captures the light text IPC 2 like Dynamic Threshold Adjusts the threshold level for binarzing to separate text from backgrounds thus capturing light text while preserving its sharpness Noise Removal 2x2 to 5x5 dot removal by matching Removes isolated dots in the size of 2x2 to 5x5 pixels Auto Separation Auto Separation Automatically detects the text area for binarizing and the photo area for dithering Outline Extract Outline Extract outline of the image Filter Emphasis Low High Emphasis contour Smooth Smoothing image by averaging ZZ NOTICE For the installation and functio
54. wer OFF Selecting photograph mode makes brightness and contrast settings effective but prevents the threshold from being set With photograph mode the darkness of image corresponds to the black pixel density making it suitable in scanning images such as photographs having gradations Photo mode photograph mode A photograph is read properly in this mode Pick start time The period from the manual insertion of the document until picking starts after the document passes the hopper empty sensor Portrait orientation A document is transported and read with the long side parallel to the moving direction Paper counter Indicates the total number of read document from start of reading until the hopper becomes empty Read operation Refers to the reading operation including Simplex reading and Duplex reading RS 232C interface A type of serial interface See Serial interface SCSI ID Used to specify a particular SCSI device when the initiator selects a target or the target reconnects to the initiator GL4 Serial interface A standard computer interface Information is transferred between devices over a single wire although other wires are used for control With a serial interface an interface cable greater than 3 meters 10 feet can be used This is often necessary in networking environments where the scanner may be shared SETUP mode In this mode users can view or set a variety of function in off line Simplex re
55. xpressly approved by the party responsible for compliance could void the user s authority to operate the equip ment L NOTICE e The use of a non shielded interface cable with the referenced device is prohib ited The length of the parallel interface cable must be 3 meters 10 feet or less The length of the serial interface cable must be 15 meters 50 feet or less e The length of the power cord must be 3 meters 10 feet or less This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conformme a la norme NMB 003 du Canada COREL PRUE SSSRESAEMEBBS VCCI AERO lt 73 ABISMATERCT COMB JERE CHATSTC CE BUL L CHW ETD COBBPIVAPCFL EV a SERIE L CHA TLS C Saera TZAT BW U FRU SPAS L E I o TIEL URW RUE LTR SL As an EnEerGYSTAR Partner Fujitsu Limited has determined that this scanner meets EnERGYSTAR guidelines for energy efficiency ENERGYSTAR is a U S registered mark The contents of this manual may be revised without prior notice All Rights Reserved Copyright 2000 FUJITSU LIMITED Printed in Japan No part of this manual may be reproduced in any form without permission Fujitsu Offices Please send your comments on this manual or on Fujitsu products to the following addresses FUJITSU COMPUTER PRODUCTS OF AMERICA INC 2904 Orchard Parkway San Jose California 95134 2022 U S A TEL 1 408 432 6333 FAX 1 408 432 3908 http www fcpa com FUJ
Download Pdf Manuals
Related Search