Frigidaire FGFU19F6QF Owner's Manual
Contents
1. Warm air entering the appliance causes it to run more Open door less often See DOOR PROBLEMS Turn control knob to a warmer setting Allow several hours for the temperature to stabilize Clean or change gasket See Care and Cleaning Chart Worn cracked or poorly fitting gaskets should be replaced APPLIANCE TEMPERATURES Interior ap pliance tem perature is too cold e Temperature control is set too low Set control to a warmer setting Allow several hours for temperature to stabilize Temperature inside appli ance is too warm Temperature control is set too warm e Door is opened too frequently or too long Door may not be seating properly Large amount of warm or hot food has been stored recently Unit has recently been disconnected for a period of time Turn control to a colder setting Allow several hours for temperature to stabilize Warm air enters the appliance every time the door is opened Open door less often See DOOR PROBLEMS Wait until the appliance has had a chance to reach its selected temperature Appliance requires 24 hours to cool down completely LO is displayed on control E7 ER EQ is displayed on control Control has been locked The control has registered an error code Press the CONTROL LOCK key for three seconds to unlock For toll free telephone support in the U S and Canada 1 800 374 42. Level Lighting Light Bulb Removal Upper Level Lighting The upper level lighting comes on automatically when the door is opened To replace the light bulbs Y IMPORTANT To disconnect power to the unit unplug the unit or switch the breaker that supplies power to the unit to the off position Replace the old bulb with a bulb of the same wattage 1 To replace the light bulb turn the temperature control to OFF and unplug the electrical cord INTERIOR LIGHTING 2 Remove the light shield by pushing in on the sides where the two tabs are located in the back and then rotate the light shield down and out 3 Replace the old bulb with a bulb of the same type and wattage 4 When replacing the light shield insert the three tabs in the front of the light shield into the slots in the control box and then rotate the rear upward until the two retaining latches lock into place 15 STORAGE FEATURES SpaceWise Glass Shelves Multi position adjustable slide out glass shelves can be moved to any position for larger or smaller packages The shipping spacers that stabilize the shelves for shipping may be removed and discarded To Adjust The Shelves e Lift front edge up e Pull shelf out e Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket Lower the shelf into the desired slots and lock into position Pal A 0000000000 oo 00000000
3. RESET key or by closing the door If the door is ajar for 15 minutes the interior light will turn off Temp Sensing Error Alert The sensor alert signals you that a problem exists with a temperature sensor The audible alarm will sound after 1 hour and the display will alternate between E8 or E9 and 10 F 23 C at half second intervals The control will then enter a mode that runs the unit in a manner that maintains the factory set cabinet temperature The audible alert can be turned off by pressing the ALERT RESET key Stuck Key Alert The stuck key alert will sound if the control reads a keypress for longer than 30 seconds The audible alert will sound and will be limited to one minute and will stop automatically The display will alternate between E7 and 10 F 23 C at half second intervals and the control will run the appliance continuously until the condition is resolved The audible alert can be turned off by pressing the ALERT RESET key bl CHANGING THE FILTER PURE ADVANTAGE Air Filter Your new Pure Advantage air filter is located inside one of the 2 Liter Door Bins The air filter cover is located on the upper right side of the control box In general you should change the air filter with Part Number EAFCBF every six months to ensure optimal filtering of freezer odors The replacement air filter can be purchased on the Frigidaire website http frigidaire stores yahoo net or call tol
4. TEMP MODE key the temperature display will toggle between F and C To turn the appliance OFF press the UP key until the warmest temperature setting of 10 F 12 C shows in the display Then press the UP key 3 times within 3 seconds to turn the unit OFF The display will then show OF To turn the unit back ON press the DOWN 7 key 3 times within 3 seconds The control will then display 10 F 12 C and may be adjusted to the desired temperature PRO SELECT Electronic Control Features Replace Air Filter When the REPLACE AIR FILTER LED is illuminated yellow the air filter needs to be replaced The control will signal for air filter replacement after 3600 hours of refrigerator operation After replacing the air filter reset the air filter timer by pressing the AIR FILTER key for 3 seconds The REPLACE AIR FILTER LED will be illuminated green for 3 seconds confirming a timer reset press amp hold alert control reset lock e door ajar e power failure e replace air fitt Control Lock To disable the keypads on the control begin by pressing the CONTROL LOCK key for 3 seconds until LO is displayed for 1 second With the control locked when keys are pressed on the control panel LO will be displayed To unlock the control press the CONTROL LOCK key for 3 seconds The display will show UL for 1 second hold to reset press amp hold air mode filter Fc reset e doo
5. hot and humid which increases internal rate of frost buildup Door is slightly open e Door is kept open too long e This is normal See DOOR PROBLEMS Open the door less often ODOR IN APPLIANCE Odors in appliance e Interior needs to be cleaned e Foods with strong odors are in the appliance Clean interior with sponge warm water and baking soda Replace air filter Cover the food tightly DOOR PROBLEMS Door will not close e Appliance is not level It rocks on the floor when it is moved slightly Floor is uneven or weak This condition can force the cabinet out of square and misalign the door Refer to Leveling in the INSTALLATION section Ensure floor can adequately support appliance Level the appliance by putting wood or metal shims under part of the appliance LIGHTING PROBLEMS Light bulb is not on 20 e The light bulb is burned out e No electric current is reaching the appliance e Control is in Sabbath mode Sb is displayed on control Follow directions under INTERIOR LIGHTING section See APPLIANCE DOES NOT RUN Depress TEMP MODE key and CONTROL LOCK key for 3 seconds MAJOR APPLIANCE WARRANTY Your appliance is covered by a one year limited warranty For one year from your original date of purchase Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or
6. is lower than the refrigerator door raise the freezer door by turning the adjustment screw clockwise using a 7 16 socket wrench See illustration below Slotted Hinge Adjustment Freezer Refrigerator To install the shelf grommet to the shelf 1 With the wire shelf installed press the shelf grommet down onto the wire that is anchored into the freezer wall Be sure to keep the larger end of the shelf grommet away from the wall INSTALLATION 2 Push the shelf grommet onto the wire until it snaps in place 3 Slide the shelf grommet into the grommet already in the freezer wall until it is flush INSTALLATION To install the handle clips to the basket 1 Place the basket on a firm flat surface 2 With the narrow side of the handle clip on the inside of the basket snap the handle clip to the recessed area in the basket Don Connan ooooo 00000 3 Once the inside surface snaps in place continue the process by rolling the handle clip slightly outward and pressing down firmly to snap onto the outside surface If installed incorrectly the handle clip will not lay flat oo009 oooona go ER DOOR REMOVAL If door must be removed e Unplug the unit or switch the breaker that supplies power to the unit to the off position e Remove the plastic top hinge cover e Hold the door in place while removing the top hinge from the cabinet e Remove the two 3 8 hex h
7. or use gasoline or other flam mable vapors and liquids in the vicinity of this or any other appliance Read product labels for flammability and other warnings e Do not operate the unit in the presence of explosive fumes e Remove and discard any spacers used to secure the shelves during shipping Small objects are a choke hazard to children e Remove all staples from the carton Staples can cause severe cuts and also destroy finishes if they come in contact with other appliances or furniture US Installation Checklist Doors Q Handles are secure and tight U Door seals completely to cabinet on all sides A Door is level across the top Leveling O Unit is level side to side and tilted 1 4 6 mm front to back Q Kick plate is properly attached to appliance O Cabinet is setting solid on all corners Electrical Power U House power turned on Q Unit is plugged in Final Checks Q Shipping material removed Q Appliance temperatures set U Registration card sent in A WARNING Child Safety e Destroy carton plastic bags and any exte rior wrapping material immediately after the unit is unpacked Children should never use these items for play Cartons covered with rugs bedspreads plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation e An empty discarded icebox refrigerator or freezer is a very dangerous attraction to children e Remove the door
8. place Recheck for levelness and adjust if necessary e Measure distance from floor to bottom of door on first unit Adjust and level second unit so door height matches Leg Level Adjustments e One full turn of all four leg levelers will raise door 5 32 e Slide second unit into place leaving a minimum gap of 3 16 between units for door swing clearance e This last step may require at least one extraction of the second unit to properly align units in a built in application Leveling Door with Adjustable Hinge Use the lower hinge adjustment to fine tune the door height and for final cabinet spacing Use a 7 16 socket or wrench to adjust the screw at the bottom of the lower hinge Adjusting Doors for Matching Tall Refrigerator Freezer Pair The doors may also be adjusted side to side with the slotted hinge for aligning the doors parallel to each other Loosen the two bolts with a 3 8 wrench and one screw with a Phillips screwdriver Shift the doors until parallel then retighten the screw and bolts securely See illustration below Lower Hinge Adjustment for Leveling the Doors of the Matching Tall Refrigerator Freezer Pair To level the doors using the adjustable lower hinge some models 1 If the refrigerator door is lower than the freezer door raise the refrigerator door by turning the adjustment screw clockwise using a 7 16 socket wrench See illustration below 2 If the freezer door
9. s of any appliance that is not in use even if it is being discarded IMPORTANT SAFETY INSTRUCTIONS WARNING Risk of child entrapment Child entrapment and suffocation are not problems of the past Junked or abandoned appliances are still dangerous even if they will sit for just a few days If you are getting rid of your old appliance please follow the instructions below to help prevent accidents We strongly encourage responsible appliance recycling disposal methods Check with your utility company or visit www recyclemyoldfridge com for more information on recycling your old appliance Before you throw away TS your old appliance MT e Remove door e Leave shelves in place so children may not easily climb inside e Have the refrigerant removed by a qualified technician WARNING Avoid fire hazard or electric shock Do not use an extension cord or an adapter plug Do not remove any prong from power cord Grounding type wall receptacle Do not under any circumstances cut remove or bypass the grounding prong Power cord with 3 prong grounded plug WARNING Electrical Information These guidelines must be followed to ensure that safety mechanisms in the design of this appliance will operate properly e The unit must be plugged into its own dedicated 115 volt 60 Hz 15 Amp AC only electrical outlet The power cord of the appliance is equipped with a three
10. workmanship when such appliance is installed used and maintained in accordance with the provided instructions Exclusions This warranty does not cover the following 1 Products with original serial numbers that have been removed altered or cannot be readily determined 2 Product that has been transferred from its original owner to another party or removed outside the USA or Canada Rust on the interior or exterior of the unit Products purchased as is are not covered by this warranty Food loss due to any refrigerator or freezer failures Products used in a commercial setting Service calls which do not involve malfunction or defects in materials or workmanship or for appliances not in ordinary household use or used other than in accordance with the provided instructions Service calls to correct the installation of your appliance or to instruct you how to use your appliance Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it is shipped from the factory Service calls to repair or replace appliance light bulbs air filters water filters other consumables or knobs handles or other cosmetic parts Surcharges including but not limited to any after hour weekend or holiday service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the state of Alaska D
11. 0000 O Freezer Baskets The freezer baskets are ideal for large items or items that do not store well on the shelves To remove the Mid Level and Tall Lower Basket Pull the basket to be removed out until the slide is fully extended Pull the basket upwards to release the basket from the retaining clips on the basket glides Adjustable Two Liter Door Bins This model is equipped with adjustable door bins that can be moved to suit individual needs To Move Door Bins e Lift the bin straight up e Remove the bin e Place the bin in desired position e Lower the bin onto supports until locked in place 16 Full Width Door Bins The full width door bin is especially designed to hold large containers or freezer bags The full width bins are removed in the same manner as the adjustable two liter door bins A Ideas for Storing Foods Meat Wrap raw meat and poultry securely so leakage and contamination of other foods or surfaces does not occur ENERGY SAVING TIPS e Locate the appliance in the coolest part of the room out of direct sunlight and away from heating ducts or registers Do not place the unit next to heat producing appliances such as a range oven or dishwasher If this is not possible a section of cabinetry or an added layer of insulation between the two appliances will help the unit operate more effi
12. 432 BEFORE YOU CALL PROBLEM Sb is displayed on control CAUSE e The control is in Sabbath Mode CORRECTION Pressing the CONTROL LOCK and TEMP MODE keys to exit Sabbath Mode SOUND AND NOISE Louder sound levels whenever appliance is on Popping or cracking sound when compressor comes on Bubbling or gurgling sound Vibrating or rattling noise e Modern freezers have increased storage capacity and more stable temperatures They require heavy duty compressors Metal parts undergo expansion and contraction as in hot water pipes Refrigerant used to cool refrigerator is circulating throughout the system Appliance is not level It rocks on the floor when it is moved slightly Floor is uneven or weak Appliance is touching the wall This is normal When the surrounding noise level is low you might hear the compressor running while it cools the interior This is normal Sound will level off or disappear as appliance continues to run This is normal Level the appliance Refer to Leveling in the INSTALLATION section Ensure floor can adequately support the appliance Level the appliance by putting wood or metal shims under part of the appliance Re level appliance or move appliance slightly Refer to Leveling in the INSTALLATION section WATER MOISTURE FROST INSIDE APPLIANCE Moisture forms on inside appliance walls e Weather is
13. FRIGIDAIRE se amp Care TABLE OF CONTENTS Important Safety Instructions COMEN eins 1122 Feature DVM NA Ice a Installation eeren sas cc raeeeser Interior Lon a DOOBREMOVAlaneneeeereenneennnnnss sen 8 Storage Features uuuuu Electronic iControl m enee 9 Energy Saving Tips SAA ies Care amp Cleaning MEAS o Before you Call CCINEIRGNIMG Tie Ala 12 Major Appliance Warranty cccmmnncncnnnnnncnnnnnnns 21 www frigidaire com USA 1 800 944 9044 www frigidaire ca Canada 1 800 265 8352 pT0z 3snbny T06090TOV IMPORTANT SAFETY INSTRUCTIONS WARNING Please read all instructions before using this appliance Definitions AX This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death Ah DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury caution CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Y IMPORTANT IMPORTANT indicates installation operation or maintenance information which is important but not hazard related WARNING For your safety e Do not store
14. Handle Set Screws are Facing Each Other with Doors Closed Matching Refrigerator and Freezer Door Handle Installation L NOTE All set screws should be tightened and sub flush Allen set screw should be seated just below the surface of the end cap of handle end cap The end caps should be drawn tight to door with no gaps Kick Plate Removal To remove the kick plate use a Phillips head 6 screwdriver and remove the two screws holding the kick plate to the cabinet Then pull the kick plate away from the unit Kick Plate Removal Leveling Rest all bottom corners firmly on a solid floor The floor must be strong enough to support a fully loaded appliance It is VERY IMPORTANT for your unit to be level in order to function properly If the appliance is not leveled during installation the door may be misaligned and not close or seal properly causing cooling frost or moisture problems To Level the Appliance While unit is laying on its back note the location of the 4 leg levelers installed at each corner These leg levelers will be used to level the unit and to adjust the height Use a carpenter s level to level the appliance from front to back and side to side Adjust the plastic leveling feet in front 2 bubble higher so that the door closes easily when left halfway open Leveling Instructions for Matching Tall Refrigerator Freezer Pair e Level door of first unit using all four levelers and slide unit into
15. L NOTE Ensure that your water supply line connections comply with all local plumbing codes Before Installing The Water Supply Line You Will Need e Basic Tools adjustable wrench flat blade screwdriver and Phillips screwdriver Access to a household cold water line with water pressure between 30 and 100 psi e A water supply line made of 1 4 inch 6 4 mm OD copper or stainless steel tubing To deter mine the length of tubing needed measure the distance from the ce maker inlet valve at the back of the freezer to your cold water pipe Then add approximately 7 feet 2 1 meters so the freezer can be moved out for cleaning as shown e A shutoff valve to connect the water supply line to your household water system DO NOT use a self piercing type shutoff valve e A compression nut and ferrule sleeve for con necting a copper water supply line to the ice maker inlet valve CONNECTING WATER SUPPLY To Connect Water Supply Line To Ice Maker Inlet Valve 1 Disconnect appliance from electric power source 2 Place end of water supply line into sink or bucket Turn ON water supply and flush supply line until water is clear Turn OFF water supply at shutoff valve 3 Remove plastic cap from water valve inlet and discard cap 4 If you use copper tubing Slide brass compression nut then ferrule sleeve onto water supply line Push water supply line into water valve inlet as far as it will go inch 6 4 mm S
16. amages to the finish of appliance or home incurred during installation including but not limited to floors cabinets walls etc Damages caused by services performed by unauthorized service companies use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies or external causes such as abuse misuse inadequate power supply accidents fires or acts of God DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN CLAIMS BASED ON IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW BUT NOT LESS THAN ONE YEAR ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE If You Need Keep your receipt delivery slip or some other appropriate payment record to establish the warranty period Se
17. bulb or any electrical part Door Gaskets e Soap and water e Wipe gaskets with a clean soft cloth Drawers amp Bins e Soap and water e Use a soft cloth to clean drawer runners and tracks e Do not wash any removable items bins drawers etc in dishwasher Soap and water e Allow glass to warm to room temperature Glass cleaner before immersing in warm water Mild liquid sprays Exterior Soap and water e Do not use commercial household cleaners Handles Non Abrasive Glass ammonia or alcohol to clean handles Cleaner e Use a soft cloth to clean smooth handles e Do not use a dry cloth to clean smooth doors Exterior amp Soap and water e Never use CHLORIDE to clean stainless steel Handles Ammonia e Clean stainless steel front and handles Stainless Steel with non abrasive soapy water and a Models Only Stainless Steel Cleaners dishcloth Rinse with clean water and a soft cloth e Wipe stubborn spots with an ammonia soaked paper towel and rinse Use a non abrasive stainless steel cleaner These cleaners can be purchased at most home improvement or major department stores Always follow manufacturer s instruction e NOTE Always clean wipe and dry with grain to prevent cross grain scratching e Wash the rest of the cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth 18 1 800 944 9044 United States 1 800 265 8352 Canada Before calling for servic
18. carded until the cubes produced are free of discoloration and taste Turning Your Ice Maker Off To stop the ice maker lift the wire signal arm until it clicks and locks in the up or OFF position The ice maker also turns off automatically when the ice container is full If your model has an adjustable freezer shelf place the shelf in the lower position so that the wire signal arm will hit the ice when the container is full Ice Maker Tips e If the ice maker will be turned off for a long period of time turn the water supply valve to the closed position e Ice cubes stored too long may develop an odd flavor Empty the ice container and ensure that the wire signal arm is in its down or ON position The ice maker will then produce more ice e Occasionally shake the ice container to keep ice separated e Keep the wire signal arm in its up or OFF position until the freezer is connected to the water supply or whenever the water supply is turned off e The following sounds are normal when the ice maker is operating e Motor running e Ice loosening from tray e Ice dropping into ice container e Running water e Water valve opening or closing fie Ice f Container mA IMPORTANT Your ice maker is shipped with the wire signal arm in the ON position To ensure proper function of your ice maker hook up water supply immediately or turn ice maker OFF by lifting the wire signal arm until it c
19. ciently Level unit so that the door closes tightly Refer to the SETTING THE TEMPERATURE CONTROL section for the suggested temperature control settings Do not overcrowd the appliance or block cold air vents Doing so causes the unit to run longer and use more energy Cover foods and wipe containers dry before placing them in the appliance This cuts down on moisture build up inside the unit Organize the appliance to reduce door openings Remove as many items as needed at one time and close the door as soon as possible CARE AND CLEANING Keep your appliance clean to prevent odor build up Wipe up any spills immediately and clean at least twice a year Never use metallic scouring pads brushes abrasive cleaners or strong alkaline solutions on any surface Do not wash any removable parts in a dishwasher Always unplug the electrical power caution e When moving the unit pull straight out Do not shift the appliance from side to side as this may tear or gouge the floor covering e Damp objects stick to cold metal surfaces Do not touch interior metal surfaces with wet or damp hands Vacation and Moving Tips Short Vacations e Leave the unit operating during vacations of less than three weeks Long Vacations Tf the appliance will not be used for several months e Remove all food and unplug the power cord e Clean and dry the interior thoroughly e Leave the door open slightly blocking it o
20. e review this list It may save you time and expense This list includes com mon occurrences that are not the result of defective workmanship or materials in this appliance PROBLEM APPLIANCE OP Appliance does not run Appliance runs too much or too long CAUSE ERATION e Appliance is plugged into a circuit that has a ground fault interrupt Temperature Control is in the OFF position Appliance may not be plugged in or plug is loose House fuse blown or tripped circuit breaker Power outage Room or outside weather is hot Appliance has recently been disconnected for a period of time Large amounts of warm or hot food have been stored recently Door is opened too frequently or too long Door may be slightly open Temperature control is set too low Gaskets are dirty worn cracked or poorly fitted BEFORE YOU CALL Visit our web site at www frigidaire com CORRECTION Use another circuit If you are unsure about the outlet have it checked by a certified technician See ELECTRONIC CONTROL section Ensure plug is tightly pushed into outlet Check replace fuse with a 15 amp time delay fuse Reset circuit breaker Check house lights Call local electric company It s normal for the appliance to work longer under these conditions It takes 24 hours for the appliance to cool down completely Warm food will cause appliance to run more until the desired temperature is reached
21. ead bolts from the top hinge with a 3 8 wrench or socket e Lift the door upwards and pull up and away from the cabinet until free of the bottom hinge pin mounted on the front of the cabinet e To replace the door reverse the above procedures and securely tighten all screws to prevent hinge slippage caution Doors are heavy Two people are recommended to remove or replace the door assembly from the cabinet inge Cover I Hinge Bolts 2 ELECTRONIC CONTROL Setting the PRO SELECT Electronic Control Cool Down Period For safe food storage allow 4 hours for the appliance to cool down completely The unit will run continuously for the first several hours Pro Select Electronic Control The Pro Select Electronic Control is located inside the appliance Temperature is factory preset to provide satisfactory food storage temperatures However the temperature control is adjustable to provide a range of temperatures for your personal satisfaction hold to reset press amp hold A if F air mode alert control I I filter Fac reset lock of a a a v e door ajar e power failure e replace air filter To adjust the temperature setting press the UP key for warmer temperature and DOWN 7 key for colder temperature on the control panel Allow several hours for the temperature to stabilize between adjustments The unit can be adjusted between 10 F 23 C and 10 F 12 C By pressing the
22. izing yourself with product features and terminology L NOTE Features may vary according to model Pro Select Ice Maker Electronic Pure Ice Bin Control Agvantage Air Baffle Upper Level Pohl Two Liter Adjustable Door Bins SpaceWise Adjustable Glass Shelves Upper Freezer Basket Mid Level Full Width Lighting Door Bins Lower Freezer Basket Adjustable Light Bottom Hinge Kick Switch Plate INSTALLATION Required Tools You will need the following tools This Use amp Care Guide provides general operating instructions for your model Use the unit only as instructed in this Use amp Care Guide Before starting the appliance follow these important first steps Phillips Location Head or e Choose a place that is near a grounded electrical outlet Do Not use an extension cord or an adapter plug e If possible place the unit out of direct sunlight and away from the range OR N dishwasher or other heat sources e Install the appliance on a floor that is level EN and strong enough to support the unit fully B8 FIXE oe Wrench loaded Wrench Set caution DO NOT install the appliance where the temperature will drop below 55 F 13 C or rise above 110 F 43 C The compressor will not be able to maintain proper temperatures inside the unit DO NOT block the kick plate on the lower front of your appliance Sufficient air circulation is essential for the
23. l arm side mounted or set the ice maker s On Off power switch to the I position rear mounted L NOTE Check with your local building authority for recommendations on water lines and associated materials prior to installing your new freezer Depending on your local state building codes Frigidaire recommends for homes with existing valves its Smart Choice water line kit 5305513409 with a 6 ft Stainless Steel Water Line and for homes without an existing valve Frigidaire recommends its Smart Choice water line kit 5305510264 with a 20 ft Copper Water Line with selftapping saddle valve Please refer to http frigidaire stores yahoo net for more information 13 ICE SERVICE If your freezer has an automatic icemaker it will provide a sufficient supply of ice for normal use During the initial startup of your freezer however no ice will be produced during the first 24 hours of operation Automatic ice makers are also optional accessories that may be installed in some models at any time Call your local dealer for information Turning Your Ice Maker On After the plumbing connections have been completed the water supply valve must be opened Place the ice container under the ice maker pushing it as far back as possible Lower the wire signal arm to its down or ON position New plumbing connections may cause the first production of ice cubes to be discolored or have an odd flavor These first cubes should be dis
24. l free in the U S and Canada 1 800 599 7569 Your electronic control is equipped with a Replace Filter indicator to remind you to change your filter See ELECTRONIC CONTROL section To Install Or Replace The Air Filter e Pull down on the front of the Pure Advantage air filter cover to release the hinged bottom cover e Allow bottom cover to swing open and then remove the old filter and discard it e Unpackage the new filter and place it inside the hinged bottom cover of the housing e Push the hinged bottom cover upward until the tab snaps into closed position Air Filter gt Remove Air Filter 12 CONNECTING WATER SUPPLY WARNING To avoid electric shock which can cause death or severe personal injury disconnect the freezer from electrical power before connecting a water supply line to the freezer caution e Copper or Stainless Steel braided tubing is recommended for the water supply line Water supply tubing made of 1 4 inch plastic is not recommended to be used Plastic tubing greatly increases the potential for water leaks and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line e DO NOT install water supply tubing in areas where temperatures fall below freezing e Chemicals from a malfunctioning softener can damage the ice maker If the ice maker is connected to soft water ensure that the softener is maintained and working properly
25. licks and locks in the UP position Check the leveling bracket on the ice maker to ensure the ice maker is level If the gap between the freezer wall and the ice maker is the same at top and bottom then ice maker is level If the ice maker is not level loosen the screw and slide the bracket to the correct position to make it level Retighten the screw You will need a Ya inch socket wrench for this task caution e DO NOT place the ice container in dishwasher e Wash the ice container in warm water with mild detergent Rinse well and dry e Stop the ice maker when cleaning the freezer and during vacations The mid level and upper level lighting comes on automatically when the door is opened a IMPORTANT To disconnect power to the unit unplug the unit or switch the breaker that supplies power to the unit to the off position Replace the old bulb with a bulb of the same wattage To replace the light bulb 1 Turn the temperature control to OFF and unplug the electrical cord 2 Remove the lens from the lamp housing by unsnapping it from the lamp housing using your fingers or a screwdriver Be careful not to break the locking tabs on the lamp housing 3 Replace the old bulb with a bulb of the same type and wattage 4 To replace the lens snap one side of the lens opening to the tab on the lamp housing Then carefully attach the other side To Remove Light Lens E Press Tabs in Direction Shown Mid
26. lide ferrule sleeve into valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT overtighten See Figure A If you use stainless steel tubing The nut and ferrule are already assembled on the tubing Slide compression nut onto valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT overtighten See Figure B Plastic Water Plastic Water Tubing Z Steel Tubing to Ice zr Clamp to Ice Maker la Steel Maker Fill Brassi Fill Tube J4 Ciamp ompression Nut Ferrule Sleeve iS Se Copper water Line water line Water Valve Water Valve Bracket Bracket Valve Inlet Valve Inlet Water Valve Water Valve Copper water line from household water supply Include enough tubing in loop to allow moving refrigerator out for cleaning 6 ft Stainless Steel water line from household water supply Figure A Copper Water Line Connection Figure B Stainless Steel Water Line Connection 5 With steel clamp and screw secure water supply line copper tubing only to rear panel of freezer as shown 6 Coil excess water supply line copper tubing only about 2 turns behind freezer as shown and arrange coils so they do not vibrate or wear against any other surface 7 Turn ON water supply at shutoff valve and tighten any connections that leak 8 Reconnect freezer to electrical power source 9 To turn ice maker on lower wire signa
27. panel The high temp icon will continue to display even if the door is closed until Sabbath mande is exited and the icon reset For further assistance guidelines of proper usage and a complete list of models with the Sabbath feature please visit the web at http www star k org NOTE While in Sabbath mode neither the lights nor the control panel will work until Sabbath mode has been deactivated The unit stays in Sabbath mode after a power failure recovery It must be deactivated with the buttons on the control panel hold to reset press amp hold alert control L A l o e Cs reset lock e door ajar e power failu 10 ALERTS There are four possible conditions that will cause the alert tone to sound High Temp Alert If the temperature inside the cabinet exceeds 23 F 5 C the HIGH TEMP LED will illuminate and after 1 hour the HIGH TEMP Alarm will sound and the cabinet temperature is shown in the display The LED and temperature alert will remain active until the cabinet temperature is below 23 F 50C The audible alert can be turned off by pressing ALERT RESET key hold to reset press amp hold e door ajar e power failure e replace air filter Door Ajar Alert This alert will sound to alert you that the door has been open for 5 minutes or more The DOOR AJAR LED will illuminate and the audible alert will sound until the door is closed The audible alert can be turned off by pressing the ALERT
28. pen if necessary to prevent odor and mold growth Moving When moving the unit follow these guidelines to prevent damage e Disconnect the power cord plug from the wall outlet e Remove foods then defrost and clean the appliance e Secure all loose items such as base panel baskets and shelves by taping them securely in place to prevent damage e In the moving vehicle secure unit in an upright position to prevent movement Also protect outside of the appliance with a blanket or similar item 117 CARE AND CLEANING L NOTE e Turning the temperature control to OFF See ELECTRONIC CONTROL section turns off the compressor but does not disconnect electrical power to the lights or other electrical compo nents Unplug the unit or switch the breaker that supplies power to the unit to the off position e Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing adhesive labels Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent or touch the glue residue with the sticky side of tape you have already removed Do not remove the serial plate Care and Cleaning Chart Cleaning Agents Tips and Precautions Interior amp e Soap and water e Use 2 tablespoons of baking soda in 1 Door e Baking soda and water quart of warm water Liners e Be sure to wring excess water out of sponge or cloth before cleaning around controls light
29. prong grounding plug for your protection against electrical shock hazards It must be plugged directly into a properly grounded three prong receptacle The receptacle must be installed in accordance with the local codes and ordinances Consult a qualified electrician Receptacles protected by Ground Fault Circuit Interrupters GFCI are NOT RECOMMENDED Do NOT use an exten sion cord or adapter plug e If the power cord is damaged it should be replaced by an authorized service technician to prevent any risk e Never unplug the appliance by pulling on the power cord Always grip the plug firmly and pull straight out from the receptacle to prevent damaging the power cord e Unplug the unit before cleaning and before replacing a light bulb to avoid electrical shock e Performance may be affected if voltage varies by 10 or more Operating the unit with insufficient power can damage the compressor Such damage is not covered under the warranty e Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to prevent the appliance from being turned off accidentally a IMPORTANT To disconnect power to the unit unplug the unit or switch the breaker that supplies power to the unit to the off position FEATURE OVERVIEW Understanding Features and Terms Your Frigidaire appliance is designed for optimal convenience and storage flexibility The illustration below is provided to assist you with familiar
30. proper operation of your unit L NOTE The exterior walls of the appliance may become quite warm as the compressor works to transfer heat from the inside Temperatures as much as 30 F warmer than room temperature can be expected Installation Installation clearances 1 25 mm e Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides 3 8 inch Top and Back 1 inch e Allow for trim kit if it is to be installed with the unit L NOTE Tf your unit is placed with the door hinge side against a wall you may have to allow additional space so the door can be opened wider Freezer Door Handle Mounting Instructions 1 Remove handle from carton and any other protective packaging INSTALLATION 2 Position handle end caps over upper and lower pre installed shoulder bolts A that are fastened into door ensuring the holes for the set screws are facing towards the outside of door if a single unit installation or the refrigerator door if installing the matching refrigerator Single Unit Installation 3 While holding handle firmly against door fasten upper and lower Allen set screws B with supplied Allen wrench 4 Repeat steps 2 and 3 to install handle if installing the matching refrigerator Ensure the holes for the set screws are facing towards the refrigerator door Ensure
31. rajar e power failure e replace air filter ELECTRONIC CONTROL Power Fail The POWER FAIL indicator light informs you that due to a power failure the cabinet temperature exceeded 23 F 5 C If the power failure lasted more than 1 hour the display alternates between showing the power failure duration Hours and DURATION LED illuminate in the display and the cabinet temperature F or C illuminates every Y second This safety feature will aid in determining what food spoilage action to take The Power Fail indicator light and duration display can be turned off by pressing Alert Reset hold to reset press amp hold air mode alert control filter F c reset lock e door ajar e power failure e replace air filter SABBATH MODE The Sabbath mode is a feature that disables portions of the refrigerator and its controls in accordance with observance of the weekly Sabbath and religious holidays within the Orthodox Jewish community To initiate or exit Sabbath Mode press and hold the CONTROL LOCK and TEMP MODE keys for 3 seconds Then Sb will be displayed on the control panel indicating that the unit is in Sabbath mode In the Sabbath mode the High Temp alarm is active for health reasons If a high temperature alarm is activated during this time for example due to a door left ajar the alarm will sound for about 10 minutes The alarm will then silence on its own and a high temp icon will be displayed on the control
32. rvice should service be required If service is performed it is in your best interest to obtain and keep all receipts Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below This warranty only applies in the USA and Canada In the USA your appliance is warranted by Electrolux Major Appliances North America a division of Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp Electrolux authorizes no person to change or add to any obligations under this warranty Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company Product features or specifications as described or illustrated are subject to change without notice USA Canada 1 800 944 9044 1 800 265 8352 To David Taylor Drive 2 Electrolux a e Charlotte NC 28262 Mississauga Ontario Canada L5V 3E4 Pil
Download Pdf Manuals
Related Search