Foundations SI258SM-D User's Manual
Contents
1. A stud MUST be located and used for at least one side of the diaper changing station PARTS LIST Parts Description Quantity Hardware for installation 3 x 1 4 Wood Screws 3 4 Finishing Washers 3 x 1 4 Machine Screws 3 4 Flat Washers Toggle Anchors Door Wall Plate INANI RR For Wood Studs For Use With Toggle Anchors ES ji SS A D A Compliance Toggle Anchors 4 4 1 Maximum Protruding Objects 4 2 5 Forward Reach 4 2 6 Parallel Approach 4 27 4 Operation Compliant when properly installed Door wall plate to be mounted on outside of restroom door 21 3 8 542 mm 17 3 16 436 mm 34 3 4 883 mm Door 1 INSTALLATION Recommended Blocking Wood double stud blocking is necessary Contact an architect a and building official to make sure the blocking is adequate and Top complies with building codes Fig a For A D A Compliance 45 114 cm AFF Remove and discard Truss Head Spanner screws from unit back Fig b Locate wood stud where left side of changing station will be mounted to the wall For A D A compliance measure up 45 114 cm from the floor and mark the wall This locates the position for the top left attachment hole NOTE Mark on wall MUST be in center of wood stud Lay top section of changing station down on changing station bed Fig c and align hol2. Foundations DIAPER CHANGING STATIONS Model 100 SSC SM Clad Stainless Steel Changing Station Installation Instructions Surface Mount Thank you for purchasing a quality Foundations product Our goal is 100 consumer satisfaction If for any reason you are not satisfied or if you have questions regardin your product or installation please contact our customer service team at 1 877 716 2757 Please DO NOT contact your distributor or reseller as we are better prepared to assist you A WARNING Failure to follow these warnings and the installation instructions could result in serious injury or death Read all instructions before installing diaper changing station Keep these instructions DO NOT discard S1258SM D INSTALLATION INSTRUCTIONS ADULT INSTALLATION REQUIRED A TOOLS REQUIRED e S Level A Measuring tape B Cc Power drill with 3 16 1 2 and 1 8 masonry bit C Power screwdriver with bull nose phillips bit D Truss head spanner bit E READ ALL INSTRUCTIONS BEFORE ASSEMBLY OF DIAPER CHANGING STATION e Unpack carton and identify all parts A WARNING This changer has six 6 recess mounting holes The diaper changing station is no stronger than the anchors or walls to which they are attached and therefore MUST be firmly secured in order to support the weight they are intended to support Contact an architect or building contractor if any questions
3. de red locking tab over top of buckle Fig i Reverse steps to loosen strap MAINTENANCE AND CLEANING Check all hardware and components monthly or as required to ensure hardware is tight and there are no missing or damaged components Take unit out of service if any component is missing or damaged and contact customer service to order replacement parts Do not substitute parts For replacement parts contact customer service at 1 877 716 2757 Clean by using a damp cloth with mild soap or mild multi purpose cleaner Do not use any strong chemical cleaners or cleaning agents that may be hazardous to children A WARNING Child should never be left unattended Avoid serious injury from falling or sliding out Always use restraint system Adding excessive weight such as parcels packages or accessories to the unit or to the bag hooks that exceed the total weight limit of 50 pounds 22 7 kg may cause the unit to be unstable or may cause a hazardous unstable condition to exist Toggle Wood Stud Anchor Break Away Fig h Top Of Locking Buckle
4. e in top left corner of changing station with mark on wall and hold in place Using a level and measuring tape mark the remaining three 3 holes After marking holes set changing station down on ground Use a power drill and appropriate bit to drill four 4 holes in the wall This may require 2 people NOTE 1 For wood studs If finished wall surface is tile or masonry over wood studs use a 7 32 masonry bit for the pilot hole until you hit the wood stud then change to 1 8 bit Use wood screws finishing washers and flat washers Fig d NOTE 2 For use with toggle anchors If finished wall surface has wood studs that are not 16 on center has metal studs or has an underlying surface of concrete block use 1 2 bit Use machine screws and flat washers Fig e For holes NOT located in a wood stud toggle anchors MUST be used Fig f See Using Toggle Anchors section Rotate plastic top section back up so that mounting hardware goes through the plastic as well as the metal back Fig b NOTE This unit incorporates a finishing collar that seats behind the changer s outside flange Center the collar as the unit is being tightened against the wall Fig g Align holes in changing station with drilled holes and secure top left corner of changing station to wall stud using the appropriate screw and washer Continue to secure the three 3 remaining corners using the appropriate screws a
5. nd washers as described in Note 1 or Note 2 Collar Wall Unit SSA Fig g 8 1 4 210 mm on cente 32 813mm a on center Fig a Truss Head Spanner Screws Fig b Surface Mount Holes U Fig c Flat Washer Wood Stud Finishing Washer Wood Screw Changing Fig d Station Toggle Wood Stud Anchor Changing Station ae Using Toggle Anchors Fig f 1 Insert metal end of toggle anchor into 1 2 hole 2 Slide zip strip down snugly against wall 3 Snap off break away pieces of toggle anchor Fig h 4 Align holes in changing station with toggle anchors and secure top left corner of changing station to wall using machine screws and flat washers Continue to secure the three 3 remaining corners using machine screws and flat washers 5 Ensure all four 4 screws are tight and snap caps over screw heads OPERATION Rotate base downward Place infant on top of the changing surface Use restraint system as described below After child has been changed remove restraint system and rotate base back up against the wall USE OF RESTRAINT SYSTEM Place child so restraint strap is located at abdomen Rotate top of buckle upward and insert strap in buckle Pull strap through buckle until snug against infant Rotate top of buckle downward to lock the strap into place Sli
Download Pdf Manuals
Related Search