Foundations 100-EV User's Manual
Contents
1. Foundations Model 100 EV Vertical Diaper Changing Station Installation Instructions A WARNING Failure to follow these warnings and the installation instructions could result in serious injury or death Read all instructions before installing diaper changing station Keep these instructions DO NOT discard 1255D Gen ASSEMBLY INSTRUCTIONS ADULT INSTALLATION REQUIRED A TOOLS REQUIRED Lo e ST Level A Measuring tape B c D Power drill with 7 32 1 8 and 1 2 masonry bits C Power screwdriver with bull nose phillips bit D x 5 e READ ALL INSTRUCTIONS BEFORE ASSEMBLY OF Diaper Changing Station e Unpack carton and identify all parts PARTS LIST Parts Description Quantity Hardware for installation 3 Wood Screws 3 4 Finishing Washers 3 Machine Screws 3 4 Flat Washers Toggle Anchors 1 1 4 Caps Door Wall Plate P HA pM AR For Wood Studs For Use With Toggle Anchors Toggle Anchors 1 1 4 Caps Door wall plate to be mounted on outside of restroom door A D A Compliance Maximum Protruding Objects Forward Reach 2 Parallel Approach 27 4 Operation liant when properly installed 7 A WARNING e A stud MUST be located and used for at least one side of the diaper changing station e The diaper changing station is no stronger than the anchors or walls to which they are2. D A Compliance 61 Rotate base downward Place infant on top of the changing surface Use restraint 155 cm ig 9 system as described below After child has been changed remove restraint system 4 and rotate base back up against the wall USE OF RESTRAINT SYSTEM ae Place child so restraint strap is located at abdomen Rotate top of buckle upward and insert strap in buckle Pull strap through buckle until snug against infant Rotate top of buckle downward to lock the strap into place Slide red locking tab over top of buckle Fig f Reverse steps to loosen strap Top Of Locking Tab MAINTENANCE AND CLEANING Check all hardware and components monthly or as required to ensure hardware is tight and there are no missing or damaged components Take unit out of service if any component is missing or damaged and contact customer service to order replacement parts Do not substitute parts For replacement parts contact customer service at 1 877 716 2757 Clean by using a damp cloth with mild soap or mild multi purpose cleaner Do not use any strong chemical cleaners or cleaning agents that may be hazardous to children Fig f A WARNING Child should never be left unattended Avoid serious injury from falling or sliding out Always use restraint system Adding excessive weight such as parcels packages or accessories to the unit or to the bag hooks that exceed the total weight limit of 50 pounds 22 7 kg may ca
3. attached and therefore MUST be firmly secured in order to support the weight they are intended to support Contact an architect or building contractor if any questions INSTALLATION Locate wood stud where left side of changing station will be mounted to the wall Measure up 61 155 cm from the floor and mark the wall This locates the position for the top left attachment hole NOTE Mark on wall MUST be in center of wood stud Align hole in top left corner of changing station with mark on wall and hold in place Using a level and measuring tape mark the remaining three 3 holes After marking holes set changing station down on ground Use a power drill and appropriate bit to drill four 4 holes in the wall This may require 2 people NOTE 1 For wood studs If finished wall surface is tile or masonry over wood studs use a 7 32 masonry bit for the pilot hole until you hit the wood stud then change to 1 8 bit Use wood screws finishing washers and flat washers Fig a NOTE 2 For use with toggles If finished wall surface has wood studs that are not 16 on center has metal studs or has an underlying surface of concrete block use 1 2 bit Use machine screws and flat washers Fig b For holes NOT located in a wood stud toggle anchors MUST be used Fig c See Using Toggle Anchors section Align holes in changing station with drilled holes and secure top left corn
4. er of changing station to wall stud using the appropriate screw and washer Continue to secure the three 3 remaining corners using the appropriate screws and washers as described in Note 1 or Note 2 A WARNING e All 4 of these locations MUST be used for safe installation The lower holes ensure installation through the metal brackets Ensure all four 4 screws are tight and snap caps over screw heads Using Toggle Anchors 1 Insert metal end of toggle anchor into 1 2 hole Slide zip strip down snugly against wall 2 3 4 Snap off break away pieces of toggle anchor Fig d Align holes in changing station with toggle anchors and secure top left corner of changing station to wall using machine screws and flat washers Continue to secure the three 3 remaining corners using machine screws and flat washers Ensure all four 4 screws are tight and snap caps over screw heads 2 Flat Washer Wood Stud Finishing Washer Wood Screw Changing Fig a Station Toggle Wood Stud Anchor Flat Wash Changing ow Station Screw Toggle Wood Stud Anchor Break Away Fig d RECOMMENDED BLOCKING Top If the walls do not have studs on center then additional blocking is necessary _ __ Fig e 4 Contact an architect or building contractor to make sure the blocking is adequate and complies with building codes ere 16 406 mm 578 mm on center OPERATION For A
5. use the unit to be unstable or may cause a hazardous unstable condition to exist
Download Pdf Manuals
Related Search