Foster FHG 3L User's Manual
Contents
1. Default A7 0 Enables alarm Ed1 and Ed2 Not used by Foster Default A8 0 alarms Ed1 and Ed2 disabled Door switch light management mode Not used by Foster Default Ado 0 High condenser temperature alarm Not used by Foster Default Ac 70 0 High condenser alarm temperature differential Not used by Foster Default AE 5 0 High Condenser temperature alarm delay Not used by Foster Default Acd 0 Off time with light sensor Not used by Foster Default AF 0 Fan management FO Fan runs all of the time for fans during defrost see F3 Default FO 0 Fan start temperature Used in conjunction with FO when FO 1 Default FO 5 0 Fans remain ON while the evaporator is 5 degrees colder than the room temperature Fans off with compressor off Used in conjunction with FO Default F2 1 Foster setting F2 0 fans are always ON FO 0 Fans in defrost Used to determine if the fans operate or not during defrost Default F3 1 Fans do not operate during defrost Fans off after dripping Fans can be stopped for a further period in minutes after defrost beyond what has been set in dd Default Fd 1 1 additional minute dripping time Serial address Used to assign an address to the instrument so that it responds to when connected to a supervisory or telemaintenance system Default HO 1 Foster setting HO 30 Function of relay2. FHG 2L amp FHG 3L REFRIGERATOR SERVICE MANUAL Foster Refrigerator Environmental Management Policy Product Support and Installation Contractors Foster Refrigerator recognises that its activities products and services can have an adverse impact upon the environment The organisation is committed to implementing systems and controls to manage reduce and eliminate its adverse environmental impacts wherever possible and has formulated an Environmental Policy outlining our core aims A copy of the Environmental Policy is available to all contractors and suppliers upon request The organisation is committed to working with suppliers and contractors where their activities have the potential to impact upon the environment To achieve the aims stated in the Environmental Policy we require that all suppliers and contractors operate in compliance with the law and are committed to best practice in environmental management Product Support and Installation contractors are required to 1 Ensure that wherever possible waste is removed from the client s site where arrangements are in place all waste should be returned to Foster Refrigerator s premises In certain circumstances waste may be disposed of on the clients site if permission is given if the client has arrangements in place for the type of waste 2 If arranging for the disposal of your waste handle store and dispose of it in such a way as to prevent its escape into the enviro
3. the parameters 4 9 4 sur Confirm by pressing _ The display shows the code of the first modifiable type C parameter Modifying the parameters After having accessed the parameters either type C or type F proceed as follows 1 10 11 12 13 14 15 Press or until the parameter to be modified is reached when scrolling through an icon appears on the display indicating the category the parameters belong to Alternatively press zel to display a menu that is used to quickly access the group of parameters to be modified Scroll through the menu using the or buttons the display shows the codes of the various categories of the parameters accompanied by the display of the corresponding icon if present s se Once having reached the desired category press _ to move directly to the first parameter in the category If there are no visible parameters in the selected category pressing amp y will have no effect At this point continue to scroll through the parameters until reaching the parameter to be modified or return to the Categories menu by pressing B for one second Press ze to display the associated value is Increase or decrease the value by pressing or buttons respectively until the desired value has been reached By pressing this will temporarily save the new value and return to displaying the parameter code Repeat the operations
4. 16A 16A we en reen rte tare PBOOFOHB10 PBOOFOHB10 PBOOFOHB10 PBOOFOHB10 Heat loads amp Consumption d 330 Compressor consumption Watts Compressor Duty Wats NENNEN Compressor Current A a Temperature controller It is strongly advised that before adjusting any Service Parameters a thorough understanding of the following instructions should be obtained Carel PBOOFOHB10 Controller Display and Symbols NOTE When the buttons are pressed a brief audible signal is emitted this signal can not be disabled 1 HACCP Pressing this button displays a sub menu used to access the HACCP parameters not used by Foster 2 9 ON OFF When pressed for more than 5 seconds switches the controller on off When OFF the controller display alternates between OFF and the air temperature as read by the air probe 3 Eel PRG MUTE Mutes the audible alarm and deactivates the alarm relay If pressed for more than 1 second the during the reception of the automatic network address assignment request package starts the address assignment procedure not used by Foster If pressed for more than 5 seconds allows access to the menu for setting the F frequent parameters If pressed for more than 5 seconds together with P allows access for setting the C configuration Parameters If pressed for more than 5 seconds when switching the instrument ON activates the procedure for s
5. 4 Auxiliary output used to power the doorframe lighting and frame heater Default H1 1 Foster setting H1 2 Disable keypad infra red Can be used to inhibit some functions relating to the use of the keypad Default H2 1 all enabled Remote control enabling code Assigns an access code to the remote control if fitted Not used by Foster 12 Default H3 0 H4 Disable buzzer H4 0 buzzer enabled H4 1 buzzer disabled Default H4 0 H5 Function of relay 5 Not used by Foster Default H5 3 H6 Lock out Buttons Not used by Foster Default H6 0 H7 Select Keypad Used to select the type of keypad on the controller Default H7 0 Use the standard controller HPr Print Profile Not used by Foster Default HPr 0 printing report disabled Note Although there are further parameters in the controller these are not used by Foster and should be left with the standard default settings Spare Parts List Part Number FHG2L FHG3L tem Scroll Compressor FL200DL 400 3 50 Scroll Compressor DS183651 230 1 50 X Compressor Scroll Compressor FL300DL 400 3 50 00 555451 Condenser coil Condenser Set LUVE STVF370 00 555448 X CondFanMotr MOTOR 1TWS 1624068 X Cond Fan Blade Blade 254 26 5A 1 1 16240059 X Cond Fan Shroud SHROUDCF 27 16240060 XT Condenser coil Condenser Coil BC6013 115 00 5554 4 X Condense
6. Proportional factor for variation in dl 50 50 50 60 A1 JjTypeofthresholdfor AL and AM flag 0 0 0 61 AL Lowtemperaturealarmthresold C F 00 00 00 62 AH High temperature alarm threshold CF 00 00 00 64 A4 Configuration of digitalinput1 0 0 0 65 A5 Configuration of digitalinput2 _ _ 0 0 0 66 A6 Stop compressor from external alarm mn 0 0 0 67 A7 _ External alarm detection delay mn 0 0 0 68 A8 Enable alarms Ed1 and Ed 1 1 flag 0 0 0 69 Ado Door switch light management mode flag 0 0 0 72 Acd High condenser temperature alarm delay mn 0 0 0 _Off time with light sensor E E a 000 Fan management fag 0 0 0 76 F2 Fanoffwithcompressoroff flag 1 0 0 Serialaddress doo 4 1 30 30 80 H1 Functonofreay4 1 flag 1 2 2 82 H3 Remotecontrolenablingcode 0 0 0 83 H4 Disablebuzzer fag 0 0 0 84 H5 Functionofreay5 J 3 3 3 85 H6 Lockoutbuttons 1 0 0 0 86 H7 SelectPDbytimeorpressure flag 0 0 0 HPr p Print profile O0 Note The total number of parameters is 105 For ease of set up Foster only use the ones listed The remaining are not used and adjustment is not recommended Param
7. ator probe failure Default dP1 30 Foster setting dP1 20 Maximum defrost duration auxiliary evaporator Not used by Foster Default dP2 30 Defrost start delay Not used by Foster Default d3 O Enable defrost at start up Activates a defrost when the defrost is switched on 0 no defrost performed when the instrument is switched on Default d4 O Defrost delay at start up Not used by Foster Default d5 O Display during defrost 1 The last temperature read prior to the start of the defrost remains on the display The display returns to displaying the temperature when the set point is achieved Default d6 1 Dripping time after defrost The time in minutes that the evaporator fans are delayed after defrost to allow for the evaporator to drip Default d6 2 Foster setting d6 7 1 Bypass alarms after defrost The time in hours that the high temperature alarms is disabled for after the end of the defrost cycle Default d8 1 Defrost priority over compressor protection Not used by Foster Default d9 0 d 1 Display defrost probe Displays the value measured by the defrost probe Once d 1 has been selected press the button to display the temperature measured by the defrost probe d 2 Display defrost probe 2 reading Not used by Foster dC Base time for defrost Not used by Foster Default dC 0 d10 Compressor running time Not used by Foster Default d10 0 d11 Runn
8. ers RTC parameters Parameter Settings The highlighted section indicate the Foster settings No Code Parameter measure Defaut FHo2I FOL 1 2 Measurementstability F 4 4 4 2 3 pProediplyrecionn 0 0 0 3 Virtvaprobe O O O0 4 5 jSeet CotF flay 0 O 0 5 6 jDecmapon flay 0 0 0 6 Display on internal terminal 1 1 1 7 AE Displayonexternalterminal 0 0 0 8 P jSeecttypeofpobe 0 O 0 9 A2 Configuratonofprobe2 J 2 2 2 10 A3 jConfigmaionofpobe3 0 0 0 11 A4 Configuration ofprobe4 0 0 0 0 12 C1 Calibrationofprobel CF 00 00 00 13 C2 Calibrationofprobe2 CF 00 00 00 14 C3 Calibrationofprobe3 CF 00 00 00 Calibration of probe 4 C SOOO ROO Temperature setpoint CF 00 00 00 19 r2 MaximumSETallowed CF 60 15 15 20 r8 Operatingmode CT fag 0 O 0 22 r5 Enabletemperature monitoring fag 0 0 0 28 m Temperature monitoring interval hours J 24 rH Maximumtemperatureread CPF Minimum temperature read C Compressor and fan start delay at startup min 0 0 0 27 cf M
9. eter Definitions 2 I3 14 I5 6 Iti KE IP IA2 IA3 JA4 St rd r1 r2 Measurement stability Defines the coefficient used to stabilise the temperature reading Probe display rate Sets the rate at which the temperature display is updated Probe average Virtual probe Used to choose whether to control the temperature based solely on the room probe reading or alternatively whether to refer to the average of the room probe S1 and probe 2 S2 see parameter A2 Select C or F Defines the unit of measure in degrees centigrade or Fahrenheit Decimal point Used to enable or disable the displaying of the temperature with the resolution to the tenth of a degree between 20 and 20 Probe displayed by instrument Select the probe to be displayed by the instrument Warning Control is always based on the virtual control probe Probe displayed on external terminal Selects the probe to be displayed on the remote terminal Select type of probe Used to select the type of probe for temperature measurement Default P standard NTC probe with range 50 to 90 C Configuration of probe 2 Used to configure the operating mode of probe 2 Default A2 2 Defrost probe Configuration of probe 3 Used to configure the operating mode of probe 3 Default A3 0 Probe 3 absent Configuration of probe 43 Used to configure the operating mode of probe 43 Default A4 0 Probe 4 absent Calib
10. etting the default parameter values If pressed for more 5 seconds together with resets any active alarm with manual reset the message TES indicates that the alarm has been reset any delays relating to the alarms are re activated 4 L UPICC If pressed for more than 5 seconds activates deactivates the continuous cycle operation the message ccE and ccE indicate respectively the start and end of the continuous cycle request If pressed together with for more than 5 seconds starts the report printing procedure provided the printer interface is connected to the controller If pressed for more than 5 seconds together with zel resets any active alarm with manual reset the message rES indicates that the alarm has been reset any delays relating to the alarms are re activated 5 9 Light If pressed for more than 1 second activates deactivates auxiliary output 2 6 AUX If pressed for more than 1 second activates deactivates auxiliary output 1 7 DOWN IDEF If pressed for mare than 5 seconds activates deactivates a manual defrost the message dFb and dFE indicate respectively the start and end of defrost ser 8 SET If pressed for more than 1 second displays and or sets the set point If pressed for more than 5 seconds together with 2 accesses the menu for setting the type C configuration parameters If pressed together with al for more than 5 seconds starts t
11. frigerator co uk Email sales foster uk com a Division of ITW UK Ltd DISPCASE SM 10 04
12. he report printing procedure provided the printer interface is connected to the controller 3 98 Compressor Illuminated when the compressor is running Flashes when the activation of the compressor is delayed by safety times 10 FAN Illuminated when the fan starts Flashes when the activation of the fan is prevented due to external disabling or procedures in progress 11 DEFROST Illuminated when defrost is activated Flashes when the activation of the defrost is prevented due to external disabling or procedures in progress 12 MX AUX Illuminated when the auxiliary output 1 and or 2 selected as AUX is activated 13 amp ALARM Illuminated following the activation of the external digital input alarm Flashes in the event of alarms during normal operation e g high low temperature or in the event of alarms from an external digital input immediate or delayed 14 CLOCK Illuminated if at least one timed defrost has been set On start up comes ON for a few seconds to indicate that the Real Time Clock is active 15 LIGHT Illuminated when the auxiliary output 1 and or 2 is selected as the LIGHT is activated 16 amp SERVICE Flashes in the event of a malfunction for example EPROM errors or probe faults 17 DISPLAY Displays the temperature in the range 50 to 150 C the temperature is displayed to the tenth of a degree between 19 9 and 19 9 C the display of the tenths can be disabled by setting the rela
13. ing time temperature threshold Not used by Foster Default d11 1 0 d12 Advanced defrost Not used by Foster Default d12 O dn Nominal defrost time Indicates the average duration of the defrost in normal operating conditions expressed as a percentage in accordance with dP1 Default dn 65 Example dn at 65 of dP1 20 minutes 13 minutes nominal defrost duration dH Proportional factor for variation in dl Default dH 50 AO Alarm and fan differential Default AO 2 0 Foster setting AO 4 0 A1 Type of threshold for AL and AH Used to select if the values of parameters AL and AH are absolute threshold or relative to the value of the set point Default A1 0 AL and AH are relative thresholds AL Low temperature alarm threshold Not used by Foster Default AL 0 alarm disabled AH High temperature alarm threshold Not used by Foster Default AH 0 alarm disabled Ad Low and high temperature alarm delay Indicates the time in minutes that the alarm from when the alarm was signalled Default Ad 120 A4 Configuration of digital input 1 Not used by foster Default A4 0 A5 Configuration of digital input 2 Not used by foster Default A5 0 A6 Stop compressor from external alarm Not used by Foster AT A8 Ado Ac AE Acd AF F0 F1 F2 F3 Fd HO H1 H2 H3 Default A6 0 External alarm detection delay Not used by foster
14. inimum time between successive starts min 0 1 1 mn 0 O0 0 29 c3 Minimum compressor ON time mn 0 0 O 30 c4 DutySetting 14A mn 0 80 80 31 cc Continuous cycle duration hours 0 0 0 33 c7 Maximum pump down PD time mn 0 O O sec 6 35 c9 Enable autostart with PD operation flag 0 0 0 36 c10 Select Pd by time or pressure flag 0 0 0 Type of defrost 0 fag 0 1 1 39 d Intervalbetweendefrosts hours 8 6 6 44 d3 Defroststartdelay min 0 0 0 45 d4 j Enabledefrstatstatup fag 0 0 0 46 d5 jDefrstdelyatstatup mn 0 0 0 47 d6 jDisplayoffduingdefrost 1 1 J 1 48 dd jDrippingtimeafterdefrost mn 2 1 J 41 49 d8 Bypassalarmafterdefrost hours 1 1 1 50 d9 Defrost priority over compressor protection 1 flag 0 0 0 51 d 1_ Display defrost probe CPF J 52 d2 Displaydefrostprobe OF J 53 dC jBasetimefordefrost flag 0 0 0 54 d10 j Compressorrunningtime hours 0 0 0 56 d12 Advanced defrost 0 0 0 57 dn Nominaldefrosttime 65 65
15. mpressor and fan start delay if fan relay present on start up When the controller is switched on the compressor and evaporator fans start after a delay in minutes equal to the value set for this parameter Default c0 0 Minimum time between two successive starts of the compressor Sets the minimum time in minutes that must elapse between two starts of the compressor irrespective of the temperature and the set point Setting this parameter limits the number of starts per hour Default c1 0 Foster setting c1 1 Minimum compressor OFF time Sets the minimum time in minutes that the compressor must remain OFF The compressor is not started again until the minimum time selected c2 has elapsed from when it last stopped Default c2 0 No minimum OFF time is set Minimum compressor ON time Sets the minimum running time for the compressor Default c3 0 No minimum running time selected Duty setting If the virtual control probe fault alarm occurs indicating a probe fault the compressor unable to operate based on temperature will run on a timed bases equal to the value set in c4 with a fixed OFF time of 15 minutes Default c4 0 minutes Foster setting c4 80 minutes Continuous cycle duration The time in hours that the compressor operates continuously to lower the temperature even below the set point Default cc 0 the continuous cycle is disabled Alarm bypass after continuous cycle The time in hou
16. nment harm to human health and to ensure the compliance with the environmental law Guidance is available from the Environment Agency on how to comply with the waste management duty of care 3 The following waste must be stored of separately from other wastes as they are hazardous to the environment refrigerants polyurethane foam oils 4 When arranging for disposal of waste ensure a waste transfer note or consignment note is completed as appropriate Ensure that all waste is correctly described on the waste note and include the appropriate six digit code from the European Waste Catalogue Your waste contractor or Foster can provide further information if necessary 5 Ensure that all waste is removed by a registered waste carrier a carrier in possession of a waste management licence or a carrier holding an appropriate exemption Ensure the person receiving the waste at its ultimate destination is in receipt of a waste management licence or valid exemption 6 Handle and store refrigerants in such a way as to prevent their emission to atmosphere and ensure they are disposed of safely and in accordance with environmental law 7 Make arrangements to ensure all staff who handle refrigerants do so at a level of competence consistent with the City Guilds 2078 Handling Refrigerants qualification or equivalent qualification co Ensure all liquid substances are securely stored to prevent leaks and spill and are not disposed of to sto
17. point 1 or point 2 If the parameter has sub parameters press to display the first sub parameter Press or to display all of the sub parameters Press e to display the associated value Increase or decrease the value by pressing Llor buttons respectively until the desired value has been reached By pressing this will temporarily save the new value and return to displaying the sub parameter code Press to return to displaying the parent parameter Procedure for setting the default parameter values To set the default parameter setting proceed as follows 1 2 3 Switch the instrument off FE Press and hold the l button Whilst holding the button switch the instrument on again until the message std is shown on the display Note the standard default values are set for parameters C and F on completion it is necessary to change the respective parameters as detailed in the parameter settings table on page 6 and 7 Classification of Parameters The parameters as well as being divided into type are also grouped into logical categories identified by the initial letters or symbols of such parameters The following table lists the categorise and the corresponding letters Parameter Oy ee C Compressor safety time and activation parameters CMP 5 EN CN AM dh H Configuration General configuration parameters addresses enabling etc A H HACCP HACCP paramet
18. r Fan Motor 5136 GridMount16W 1547027 X Drier DMLOS 00555889 X X LiquidReceiver VLR 122637 3 8 Sweat amp 01 15482010 X X HP Switch Setat28BAR 00555386 X X Vaporiser TrayHeater Copper Coil TBA _ L lt L K X lt X lt Evaporator Coil BC6013 114 FHG2L 00 555475 Evaporator Coil BC6013 114 FHG3L 00 555476 5133 Ring 10W 200mm 00 599687 NO 03 68 209300 68 20 15451105 Expansion Valve Body TES2 NL68Z34300 68 15450386 NO 02 68 2092 68 2072 15451104 X po p p MCB Siemens 5SY6316 8 TP 16 Amp 3 Pole 16240209 Wiring diagrams The drawings numbers for the display cases are as follows FHG2L 2 door unit single phase 00 233867 02 FHG2L 2 door unit three phase 00 233868 02 FHG3L 3 door unit three phase 00 233869 02 15 FHG2L 2 door unit single phase 00 233867 02 FHG2L 2 door unit three phase 00 233868 02 FHG3L 3 door unit three phase 00 233869 02 J FOSTER REFRIGERATOR Foster European Operations France Foster Refrigerator France SA Tel 33 01 34 30 22 22 Fax 33 01 30 37 68 74 Email commercial fosterfrance com Germany Foster Refrigerator Gmbh Tel 49 2333 839375 Fax 49 2333 839377 Email info foster gmbh de Foster Refrigerator Oldmedow Road Kings Lynn Norfolk PE30 4JU Tel 01553 691122 Fax 01553 691447 Website www fosterre
19. ration or offset probe 1 Calibration or offset probe 2 Calibration or offset probe 3 Calibration or offset probe 4 These parameters are used to correct the temperature by the probes using an offset Example To decrease the temperature measured by probe 1 by 2 3 degrees set C1 2 3 Set point Establishes the controller set point Default St 0 0 Control delta Establishes the value of the differential or hysteresis used to control the temperature Default rd 2 0 Foster setting rd 4 0 Minimum allowed set point Determine the set point minimum value Default r1 50 Foster setting r1 26 Maximum allowed set point Determine the set point maximum value Default r2 60 Foster setting r2 15 r3 r4 r5 rH rL cO c1 c2 c3 c4 CC c6 c7 c8 c9 c10 Operating mode The controller can work as a thermostat and defrost controller r3 0 or as a simple thermostat in direct operation r3 1 or as a simple thermostat in Reverse cycle operation r3 2 Default setting r3 0 Automatic variation of the set point in night time operation Default 3 0 Not used by Foster Enables minimum and maximum temperature monitoring Effective interval for monitoring the maximum and minimum temperature Maximum temperature measured in the interval rt Minimum temperature measured in the interval rt These parameters are used for recording the temperature Not used by Foster Co
20. rm drains foul drain surface water to soil Contents 3 1202 y Page Introduction O 2 Accessing the type F parameters Accessing the type C parameters nam EE Introduction The display case are manufactured in two formats FHG 2L 2 doors and the FHG 3L three doors There are also Multiplex options that are a combination of two FHG 2L cases to make a FHG 4L or a combination of the FHG 2L and FHG 3L to make a FHG 5L Technical Specification Model 2 Door 3 Door 4 Door 5 Door External Dimensions m Height m 2100 2100 2100 2100 Width m 1684 2463 3254 4035 Depth m 900 900 900 900 Internal Dimensions m Height m 1354 1354 1354 1354 Width m 1564 2343 3128 3907 Depth m 550 550 550 550 No of Shelves 12 18 24 30 Shelf capacity each Kg 40 40 40 40 Door System Schott Schott Schott Schott Refrigeration System Hitachi Hitachi FL200 Compressor uox FL200 DL 400v y hase 400v 3 phase Hitachi From Aug nacn DS 183651 2004 De 230v 1 phase 230v 1 phase Hitachi FL300DL 400 3 Phase x 2 Hitachi FL300DL 400 3 Phase R404A R404A Refrigerant Pata dE 2500 grms 2500 grms x 2 3500 grms Vaporisaton HotGas HotGas HotGas HotGas Hor sasand Hot Gas and Hot Gas and Hot Gas and Defrost Type Electric 1 kW Electric Electric Electric 1 5 kW 2 1kW 2 5 kW 400 3 50 Electrical Supply Capacity 16A 16A
21. rs that the temperature alarm is deactivated after a continuous cycle Default c6 2 hours Maximum pump down time Not used by Foster Compressor start delay after opening PD valve Not used by Foster Default c8 5 Enable autostart function with PD operation Not used by Foster Default c9 0 Select pump down by pressure or time Not used by Foster Default c10 0 c11 do di dt1 dt2 dP1 dP2 d3 d4 d5 d6 dd d8 d9 Delayed compressor delay Not used by Foster Default c11 4 Type of Defrost Sets the type of defrost required Default dO O Foster setting dO 1 Hot gas defrost terminated by evaporator probe or in the event of probe failure by time see dP1 Interval between defrosts The defrosts are performed periodically at an interval equal to the value of dl in hours The interval is cyclical and is maintained if the controller is turned OFF when the controller is turned back ON a defrost will occur if the interval was exceeded Default dl 8 Foster setting dl 6 End defrost temperature evaporator probe The evaporator probe termination temperature in the event of a probe failure the defrost will be terminated by time see dP1 Default dt1 4 0 Foster setting dt1 20 0 End defrost temperature auxiliary evaporator Not used by Foster Default dt2 4 0 Maximum defrost duration Evaporator Maximum time in minutes for defrost in the event of evapor
22. ted parameter 18 HACCP Illuminated if the HACCP function is enabled Flashes when there are hew HACCP alarms stored HA and or HF alarm shown on the display 19 CONTINUOUS CYCLE Illuminated when the CONTINUOUS CYCLE function is activated Flashes if the activation of the function is prevented due to external disabling or procedures in progress e g minimum compressor OFF time Setting the set point To display the set point proceed as follows sut i 1 Press for more than 1 second to display the set point 2 To increase the set point press or to decrease the set point press until the desired value is reached 3 To confirm the value press A Programming the controller The parameters can be modified using the front keypad The operating parameters are divided into two families Frequent parameters type F and configuration parameters type C Access to the configuration parameters is protected by a password that prevents unwanted modification or access by unauthorised persons Accessing the type F parameters Press for more than 5 seconds if an alarm is active the buzzer is muted the display shows the code of the first modifiable type F parameter Accessing the type C parameters 1 Press Sland Pi together for more than 5 seconds the display will show the number 00 2 Press amp until the display shows 22 the code allows access to
Download Pdf Manuals
Related Search