Fishman Aura Pro User's Manual
Contents
1. Press and hold the Tuner and Anti Feedback buttons simultaneously 3 Plug in the guitar Continue to hold the Tuner Anti Feedbackbuttons for three seconds after you plug in 4 Release the Tuner Measure buttons then unplug the guitar to complete the procedure Defaults EQ for all four Images reverts to at Relative Phase settings return to default state Anti Feedback frequency is reset to 100Hz 17 Electrical Speci cations Digital Signal Path A D D A conversion 24 bit Signal Processing 32 bit Typical in use current consumption 9VDC 18mA Typical 9V lithium battery life 54 hours Typical 9V alkaline battery life 27 hours Nominal output impedance 1k Ohm Recommended load impedance 10k Ohm and up Input Trim gain range 6dB to 6dB Maximum output level onset of clipping 5dBV Baseline noise 92dBV Dynamic Range 97dB Bass control 12dB 90Hz Midrange control 12dB 1kHz Treble control 12dB 6kHz Anti Feedback cut depth 13 5dB The speci cations and information in this manual are subject to change without notice www shman com 513 300 150 Rev C 2 092. in memory until you push the Measure button again To turn the circuit off push and hold the Anti Feedback button for ve seconds Battery Replacement Pull the small tab at the top of the Aura Pro toward you The body of the preamp will swing out revealing the battery compartment Observe the polarity marks on the battery compartment and install a fresh 9V battery See page 15 We recommend a lithium battery for extended battery life 14 Input Trim and VU Meter Adjust this set and forget control to accommodate the dynamics of your playing style When you set Input Trim to the optimum level you can play strongly without distortion and play quietly without hiss To Set the Input Trim Unplug the guitar and pull the small tab at the top of the Aura Pro toward you Locate the small circular potentiometer on the right side of the preamp To turn on the VU meter move the Edit Play switch to Play and plug in the guitar while holding the Tuner button The Tuner display will ash and the pitch LEDs two arrows and a circle will now display the input level of the preamp Play the instrument strongly and watch the LED display Use a small at head screwdriver to raise or lower the trim control so all three LEDs ash occasionally with hard strumming To exit the VU meter push the Tuner button 15 16 Restore Factory Defaults 1 Unplug the guitar and move the tone controls to the center detent position 2
3. USER GUIDE AURA PRO RETAIL 3 Welcome Thank you for making Fishman a part of your acoustic experience We are proud to offer you the nest acoustic ampli cation products available high quality professional grade tools to empower you to sound your very best We are con dent Aura Pro will both enhance and inspire your music making Troubleshooting Installation by a quali ed professional is strongly recommended Should you have any problems please check with your installer or refer to the online installation guide for this product Technical support troubleshooting tips and installation information can be found at http www shman com support 4 Image Chart Once you upload Images into your Aura Pro use this chart for quick reference Image Instrument Name Microphone Mic Distance 1 2 3 4 5 Fundamentals To experience the bene ts of Aura install the Aura Gallery CD on your computer then upload Images into the Aura Pro pre amp Flip open the preamp and connect the included USB cable to the side of the preamp USB mini jack 6 Quick Start Before you begin set the controls as shown 1 Plug in Use a inch instrument cable 2 Tune up Set Play Edit switch to Play Press Tuner button When engaged Tuner mutes the output Press again to exit Tuner 3 Select an Image Raise the Volume and use the Image switch to browse the Images 4 Blend in pickup Turn Blen
4. d control left to mix pickup with Image 7 5 Pickup tone Set Play Edit switch to Play and adjust tone controls 6 Image tone Set Play Edit switch to Edit and adjust tone controls Move switch back to Play to lock Image tone 7 Control Feedback If feedback occurs push Phase switch If feedback recurs when you change your location press switch again Push Anti Feedback button once Turn up Volume then either dampen the strings while tapping the body or play the troublesome note until the lter eliminates feedback Note Aura Pro is a programmable preampli er To restore factory defaults see page 16 8 Power Plug in the guitar and the Aura Pro switches on To conserve the battery remove the instrument cable from the guitar when the system is not in use The LEDs in the tuner display ash once at power up to tell you the preamp is on Low Battery Indicator When the Battery LED ashes once every three seconds you have approxi mately 1 5 hours before the battery is exhausted Change it at the next opportu nity When the Battery LED ashes every half a second the battery is practically spent and should be changed immediately 9 Tuner Plug an instrument cable into the endpin jack move the Play Edit switch to Play and press the Tuner button to turn the circuit on and off This digital chromatic tuner accommodates all standard and alternate tunings When engaged the tu
5. ner also mutes the output Note that the tuner is calibrated to A 440 10 Controls Image Your Aura Pro is factory loaded with four Images created especially for this instrument Each Image corresponds to a different microphone type and position Contact the guitar s manufacturer to identify the microphone associated each Image Volume For the cleanest noise free sound set the Volume as high as possible without causing your amp or mixer to distort Blend Use the Blend slider to set the balance between the pickup and the Image 11 Tone Controls amp Play Edit Switch The Play Edit switch lets you EQ the pickup and Image s independently Pickup EQ Move the Play Edit switch to Play and adjust the Bass Mid and Treble controls Switch to Edit and the preamp retains the pickup EQ settings disengages the pickup tone controls and enables Image EQ Return to Play and the preamp holds the pickup EQ settings until the Bass Mid or Treble controls are moved regardless of the current position of the controls Programmable Image EQ To EQ an Image move the Play Edit switch to Edit The LED ashes to indicate Edit mode Move the Blend slider to Aura select an Image and adjust the tone controls You can program EQ for each of the four Images simply select another Image and adjust the controls Switch to Play and the preamp retains the Image EQ settings disengages the Image tone controls and enables pickup EQ Go back t
6. o Edit and the preamp holds the Image EQ settings until the Bass Mid or Treble controls are moved regardless of the current position of the controls 12 Phase Switches Phase global Use the Phase switch to improve bass response at low volume and suppress feedback at high volume Push the Phase switch in and out and leave it in the position most pleasing to your ear If feedback occurs push the switch again Relative Phase pickup phase To change the character of your blended sound you may wish to change the phase of the pickup relative to the Image There is no best position for Relative Phase and where you set it is a matter of personal taste 1 Center Blend slider and switch to Edit The LED ashes to indicate Edit mode 2 Push the Tuner button to toggle the relative pickup phase default 3 To exit Relative Phase move the Play Edit switch to Play You can program different Relative Phase settings for each of the four Images Select a different Image and repeat above procedure 13 Anti Feedback Use this search and destroy Anti Feedback lter in addition to the Phase switch 1 Push Anti Feedback button once The letter F in tuner display will ash 2 Turn up Volume then either dampen the strings while tapping the body or play the troublesome note until the feedback begins The automatic lter will identify and eliminate the feedback The circuit will hold this offending frequency
Download Pdf Manuals
Related Search