Fisher-Price G5911 User's Manual
Contents
1. 2 Parts IMPORTANT Please remove all parts from the package and identify them before assembly The kickstand is packaged within the pad at the factory Before beginning assembly please remove kickstand from the pad 2 Side Rails 2 Retainers with Lock Nut Cross Brace Front Tube Kickstand Toy Bar 3 Toys All Shown Actual Size 8 x 1 9 cm 3 4 Screw 2 8 x 3 cm 11 8 Screw 2 M4 Lock Nut 2 Inside Retainers Occasionally a consumer may experience a problem with one of our products If this should happen please call us rather than return this product to the store Usually we can solve the problem over the telephone or send you replacement parts Great Britain telephone 01628 500302 Consumer Information Seat Back Tube Pad Australia Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia Consumer Advisory Service 1300 135 312 New Zealand 16 18 William Pickering Drive Albany 1331 Auckland IMPORTANT Before assembly inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Mattel for replacement parts and instructions if needed Never substitute parts This package contains small parts in its unassembled state Adult assembly is required CAUTION Position each side rail so that the button faces outward Fit the cross brace between the side ra2. before charging If removable rechargeable batteries are used they are only to be charged under adult supervision Hint We recommend using an alkaline battery for longer battery life Battery Installation 8 Securing Your Infant Place your child in the seat Position the restraint pad between your child s legs Fasten the restraint belts to each side of the restraint pad Make sure you hear a click on both sides Check to be sure the restraint system is securely attached by pulling it away from your child The restraint system should remain attached Restraint Pad Restraint Belt Restraint Belt To prevent serious injury or death Always use the restraint until child is able to climb in and out of the chair unassisted It is dangerous to use this product on an elevated surface Never leave child unattended WARNING 2 Recline Select a seat position for your child s comfort Upright or Recline Upright While pressing the button on each side rail lift the seat back Recline While pressing the button on each side rail lower the seat back IMPORTANT Before each use inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Mattel for replacement parts and instructions if needed Never substitute parts Seat Position Press Button Press Button Lift 1 To prevent serious inj
3. the upper pocket on the pad onto the seat back tube Fasten the pad buckles around each side rail 8 Pad Pad Slot Press Seat Back Hardboard Seat Back Tube Pad Buckles Side Rail Assembly 7 Locate the battery compartment on the bottom of the vibrations unit Loosen the screw in the battery compartment door with a Phillips screwdriver Lift to remove the battery compartment door Insert one LR20 D alkaline battery as indicated inside the battery compartment Replace the battery compartment door and tighten the screw with a Phillips screwdriver Do not over tighten Battery Compartment Battery Safety Information 1 5V LR20 D SHOWN ACTUAL SIZE Batteries may leak fluids that can cause a chemical burn injury or ruin your product To avoid battery leakage Do not mix old and new batteries or batteries of different types alkaline standard carbon zinc or rechargeable nickel cadmium Insert batteries as indicated inside the battery compartment Remove batteries during long periods of non use Always remove exhausted batteries from the product Dispose of batteries safely Do not dispose of batteries in a fire The batteries may explode or leak Never short circuit the battery terminals Use only batteries of the same or equivalent type as recommended Do not charge non rechargeable batteries Remove rechargeable batteries from the product
4. ar straps through the slot in the toy rings Fasten the straps Or attach the toys to the pad straps see Step 4 Toy Bar 5 Toys Plug Plug Toy Bar Hint Pull the monkey s head for a short tune 11 Storing the Restraint System for Toddler Use 8 Large Slot Small Slot Small Slot Insert the restraint belts back through the small slots in the pad Insert the restraint pad down through the large slot in the pad Rotate the kickstand out Push down on the seat bottom to be sure the kickstand is in position Kickstand 7 Kickstand Turn the rocker face down Tuck the ends of the restraint pad underneath the buckles as shown 9 Fisher Price Inc a subsidiary of Mattel Inc East Aurora NY 14052 U S A 2004 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc PRINTED IN CHINA G5911pr 0726 The frame pad toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth Do not use bleach Do not use harsh or abrasive cleaners Rinse clean with water to remove residue Care
5. ils as shown Push the cross brace down to snap it into place This may require a lot of force Side Rails 1 Insert a screw through the hole in the bottom of each side rail and into the cross brace Tighten the screws with a Phillips screwdriver Do not over tighten 3 2 Shown Actual Size 8 x 1 9 cm 3 4 Screw Cross Brace Button Side Rails Push Cross Brace Insert the seat back tube into the socket in each side rail While pressing the tabs on the ends of the seat back tube continue to insert the seat back tube into the sockets in each side rail until the tabs snap into place Make sure you hear a snap on each side Pull the seat back tube up to be sure it is secure in the side rail sockets 3 Seat Back Tube Press Tabs Side Rail Sockets Push Assembly 4 4 Locate the hole in each side rail With the vibrations unit facing forward fit the front tube to the side rails as shown Hold the front tube in place and proceed to step 5 Front Tube Side Rail Hole Side Rail Hole Vibrations Unit Insert a 8 x 3 cm 11 8 screw through the outside of each side rail and into the ends of the front tube Side Rail Side Rail Front Tube 5 Shown Actual Size 8 x 3 cm 11 8 Screw IMPORTANT Please follow the next assembly step 6 carefully to completely secure the front tube to the side rails Assembly 5 Pos
6. ition the assembly face down as shown While pressing the tab on each end of the kickstand insert the kickstand into the receptacle in each side rail as shown Push the kickstand into the receptacles until the tabs snap into place Make sure you hear a snap on each side Pull the kickstand to be sure it is secure in the receptacles 7 Press Tab Press Tab Kickstand Receptacles 6 Shown Actual Size Fit a retainer with lock nut onto the end of the screw and to the inside of a side rail Tighten the screw with a Phillips screwdriver Do not over tighten Repeat this procedure to fasten the screw in the other end of the front tube and side rail using the remaining retainer with lock nut Rounded Side M4 Lock Nut 2 Inside Retainer Retainer with Lock Nut Hint A lock nut has been factory assembled to the retainer During shipment the lock nut may have fallen out of the retainer If it has please fit it into the hexagonal hole in the retainer so that the rounded side of the lock nut faces out Assembly 6 Turn the hardboard over and insert it into the slot in the front edge of the pad Fasten the pad buckles on the front edge of the pad and underneath the seat Make sure you hear a snap on both sides Press the fasteners together in the seat back portion of the pad Assembly is now complete 9 Pad Buckles Turn the assembly upright Fit
7. ury or death Use the upright position only when child has developed enough upper body control to sit without leaning forward WARNING Upright Lower Set Up amp Use 9 Toys 4 Fit the pad straps through the slot in the toy rings Fasten the straps Or attach the toys to the toy bar straps please see Step 5 Toy Toy Toy Strap Loosen Tighten B Anchored End Free End Anchored End Free End B 3 To tighten the belts Feed the anchored end of the restraint belt up through the buckle to form a loop Pull the free end of the restraint belt Repeat this procedure to tighten the other restraint belt To loosen the belts Feed the free end of the restraint belt up through the buckle to form a loop Enlarge the loop by pulling on the end of the loop toward the buckle Pull the anchored end of the restraint belt to shorten the free end of the restraint belt Repeat this procedure to loosen the other restraint belt B B Strap Strap Hint Pull the monkey s head for a short tune Securing Your Infant 10 Calming Vibrations Make sure your child is properly secured in the seat Slide the power switch to the on position for calming vibrations Slide the power switch to the off position to turn vibrations off 6 Power Switch Fit the plugs on each end of the toy bar into the sockets in each side rail Fit the toy b
8. ww w fis her p ric e c o m Infant to Toddler Rocker Infant Seat Toddler Seat L E A R N I N G P A T T E R N S L E A R N I N G P A T T E R N S Model Number G5911 IMPORTANT KEEP INSTRUCTIONS FOR FUTURE REFERENCE WARNING Please keep this instruction sheet as it contains important information Use the upright position only when your child has developed enough upper body control to sit without leaning forward Always use the restraint until your child is able to climb in and out of the chair unassisted Adult assembly is required Tool needed for assembly Phillips Screwdriver not included Requires one LR20 D alkaline battery not included for vibrations unit operation Warning To prevent serious injury or death It is dangerous to use this product on an elevated surface Never use on a soft surface bed sofa cushion since product can tip over and cause suffocation in soft surfaces Always use the restraint until child is able to climb in and out of the chair unassisted Never leave child unattended Use the upright position only when child has developed enough upper body control to sit without leaning forward Never use as a carrier or lift while child is seated Never use the toy bar as a handle Reclined position not recommended for children who can sit up by themselves 6 months approximately until 9 kg WARNING
Download Pdf Manuals
Related Search