Fisher-Price 79638 Instruction Sheet
Contents
1. e Push each seat height adjuster to be sure they are completely on the seat bottom tubes Front Leg Hole e Insert a 8 x 3 4 screw through each seat height adjuster and the ends of the seat bottom tube e Tighten the screws with a Phillips screwdriver Front Base Do not over tighten N A 8 x 3 4 Screw 2 fe SHOWN ACTUAL SIZE 7 6 _ K Y T E 10 x 8 Black Screw 2 Seat Ms Me ea A SHOWNACTUALSIZE Height gt Height QE Adjuster ot i Adjuster C e ee ee M a TA Fit the frame front legs onto the front base e Fit a screw retainer over a hole in the front leg eee eee eee e Insert a 10 x 7 8 black screw through the screw retainer x yo Te and front leg o L Seat JS e Tighten the screw with a Phillips screwdriver Do not Ki _ Bottom N fy Tube Ends over tighten K e Repeat this procedure to secure the other end of the SALA front base with the remaining screw retainer and 10 x 7 8 black screw 1 44 A be Back and A Hint The 10 x 7 8 black screws may have been assembled to Bottom View the screw retainers e From the back and bottom of the assembly insert a 8 x 3 4 screw through both seat height adjusters and the ends of the seat bottom tube Tighten the screws with a Phillips screwdriver 7 Do not over tighten SHOWN ACTUAL SIZE n Assembly Pad Hole e Ins2. e Remove the waist shoulder belts and crotch belt through the slots in the pad e Unfasten the pad fasteners from the front edge of the seat bottom e Remove the pad To replace the pad and headrest refer to Assembly steps 15 19 IMPORTANT Never use this product without the restraint system Replace the waist shoulder belts and crotch belt For other countries outside the United States Canada call 1 800 567 7724 or write to Mattel Canada Inc 6155 Freemont Blvd Mississauga Ontario L5R 3W2 Great Britain telephone 01628 500302 Australia Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia Consumer Advisory Service 1300 135 312 New Zealand 16 18 William Pickering Drive Albany 1331 Auckland Fisher Price Inc a subsidiary of Mattel Inc East Aurora New York 14052 U S A 2002 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc Printed in China 79638c 0920
3. FisherPrice Healthy Care High Chair Product features and decoration may vary from the photo above Model Number 79638 79639 79640 79641 B2875 Please keep this instruction sheet for future reference as it contains important information Adult assembly is required Tool needed for assembly Phillips Screwdriver not included Discover what s Warnings and Caution A WARNING Prevent serious injury or death from falls or sliding out e The child should be secured in the high chair at all times by the restraining system either in the recline semi recline or upright position The restraint belts must be adjusted to fit your child snugly The tray is not designed to hold the child in the chair Always keep child in view while in the high chair Never leave child unattended It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted CAUTION This product contains small parts in its unassembled state Adult assembly is required Consumer Information Occasionally a consumer may experience a problem with one of our products If this should happen please call us toll free rather than return this product to the store Usually we can solve the problem over the telephone or send you replacement parts Please call Fisher Price Consumer Relations toll free at 1 800 432 5437 8 AM 6 PM EST Monday through Friday Hea
4. ert the crotch belt through the slot in the pad Make sure the crotch belt is not twisted Front View CULL Aneen Sl re A et ee aA o Elastic Loops 15 Back and Bottom View e Lift the assembly upright e From the front of the assembly place the pad onto the seat Lift the bottom of the pad Insert the two elastic loops on the pad through the holes in the seat bottom e From the back and bottom of the seat hook the elastic loops to the tabs on the seat Assembly Upper Shoulder Shoulder Belt Slots Shoulder Portion Portion Lower Shoulder Belt Slots e Fold the top of the pad down e Remove the shoulder portion of the waist shoulder belts by feeding them through the slots in the seat back Lift the top of the pad e Thread the waist shoulder belts through the bottom slots in the back of the seat pad Assembly Handle Pad Strap Caa Elastic ff epee I der d e 1 ees es F From behind the seat be sure the shoulder portion of the waist shoulder belts are secure in the seat back slots e Hook the elastic loops on each side of the pad onto the tabs in the seat back Storage e At an angle fit the storage caddy onto the tab on either frame Assembly is now complete 10 Securing Your Child IMPORTANT Before each use inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any pa
5. k and forth to be sure they are secured to the seat bottom If the seat bottom tubes move you have probably not fastened them properly Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned Replace and tighten the screws Seat Bottom Tubes Footrest 2 e Slide a seat bottom tube through each set of plastic rings on the seat bottom 10 x 7 8 Black Screw 2 SHOWN ACTUALSIZE e Insert two 10 x 7 8 black screws through the footrest and into the seat bottom S e Tighten the screws with a Phillips screwdriver 4 Do not over tighten Assembly Seat Back Pin Frame Leg Opening Seat Bottom Assembly 5 e Pull the frame leg out on each frame to open Make sure it clicks into place e Turn the seat bottom assembly upright Fit the seat back pins into the openings in the top side of mne Short Leg the seat bottom assembly 10 x 7 8 Black Screw SHOWN ACTUAL SIZE y Back Base Long Tapered Leg Tube Front Base e Identify the back and front base The back base has short leg Turn the seat assembly face down tubes and the front base has long tapered leg tubes You will e Insert the hinge rod through the hinge on the seat back use the back base for the next assembly step and seat bottom as shown e Insert a 10 x 7 s black screw into the hinge rod e Tighte
6. n the screw with a Phillips screwdriver Do not over tighten e Set the seat assembly aside for Assembly step 12 Assembly Frame Decorated Side Seat Height Adjusters Press Lever oo of oo oP e While pressing the levers on the seat height adjusters lift ee them to position 4 on the frame front legs as shown oo 9 Back Base Hole pow 7 Jo 2 10 x s Black Screw 2 Screw Retainer lt 2 N SHOWN ACTUAL SIZE y l y e Position a frame so that the decorated side is outward e Insert the back leg of a frame into the back base e Fit a screw retainer over the hole in the back base as shown e Insert a 10 x 7 s black screw through the screw retainer and back base e Tighten the screw with a Phillips screwdriver Do not over tighten e Repeat this procedure to attach the other frame back leg to the other side of the back base Seat Assembly Seat Bottom Tubes Hint The 10 x 7 8 black screws may have been assembled to the screw retainers e Fit the seat assembly between the two frames e Insert the seat bottom tubes into the sockets in each seat height adjuster Hints Be sure the seat height adjusters are in the same position position 4 You may need to push the frames apart slightly to fit the seat bottom tubes into the seat height adjuster sockets Assembly Seat Bottom Tube Ends i 8 x 3 4 Screw 2
7. ont of the base tray adjust the base tray forward or backward PT an R Fit the base tray onto the seat armrests Push down until the base tray snaps into place l l e While squeezing the latches underneath the base tray Hint Before use thorougly wash all parts the trays that may adjust the base tray forward or backward contact food 12 Using the Trays Hint The base tray can be removed two ways see steps 9 and 10 Base le pees Tray Squeeze i y Squeeze Fit the food tray into the base tray as shown Hint Before use thorougly wash all parts the trays that may contact food e Squeeze one or both of the latches underneath the base tray and lift e While pushing the release bar on the front of the base tray pull the tray base towards you and remove 13 Adjusting the Seat WARNING Prevent serious injury or death from falls or sliding out It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted Hint Adjust the seat height to any of seven positions Seat Height Adjuster N To adjust the seat height e Press the levers on both seat height adjusters and lift or lower the seat to the desired height e Make sure both sides of the seat are adjusted to the same height Push the seat bottom to be sure the seat is locked in place 14 Hin
8. ring impaired consumers using TTY TDD equipment please call 1 800 382 7470 Or write to Fisher Price Consumer Relations 636 Girard Avenue East Aurora New York 14052 Parts Food Tray Seat Back Base Tray Seat Bottom Frame Hinge 10 x 7 s Rod Black Screw wnat Storage Caddy 8 x 3 4 Screws 2 Seat Bottom Tubes 4 pand L 8 x 3 4 lt i Screws 4 Screw Retainers SS 10 x 7 2 Black Screw 4 Footrest Back Base Front Base 10 x 7 8 Black Screws 8 x 3 4 Screw 8 SHOWN ACTUAL SIZE 10 x 7 8 Black Screw 7 SHOWN ACTUAL SIZE Assembly IMPORTANT Before assembly inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts Seat Footrest a al Plastic ate Rings AALI bo IN m N Seat Bottom peA Align the holes in the plastic rings and the seat bottom tubes 8 x 3 4 Screw 4 Insert a 8 x 3 4 screw through each plastic ring and into the 4 SHOWN ACTUAL SIZE 4 seat bottom tubes as shown V Tighten the screws with a Phillips screwdriver e Place the seat bottom face down on a flat surface At an angle fit the footrest on the seat bottom as shown Do not over tighten Push the seat bottom tubes bac
9. rts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts AN WARNING Prevent serious injury or death from falls or sliding out The child should be secured in the high chair at all times by the restraining system either in the recline semi recline or upright position The restraint belts must be adjusted to fit your child snugly The tray is not designed to hold the child in the chair Waist Shoulder Waist Shoulder errr rrr rrr ny EOS acco a 8 se 2 sananne y a e Sees e Place your child in the seat Position the crotch belt between your child s legs e Fasten both waist shoulder belts to each side of the crotch belt Make sure you hear a click on both sides e Check to be sure the restraint system is securely attached by pulling it away from your child The restraint system should remain attached Securing Your Child WW Anchored To tighten the waist belts e Feed the anchored end of the waist belt up through the buckle to form a loop Q e Pull the free end of the waist belt JS eS e Repeat this procedure to tighten the other waist belt nr E To loosen the waist belts e Feed the free end of the waist belt up through the buckle to form a loop Q j Enlarge the loop by pulling on the end of the loop toward the buckle e Pull the anchored end of the waist belt to shorten the free end of
10. t Adjust the seat angle to any of three positions Upright Semi Recline or Recline Recline To adjust the seat angle e Squeeze the seat back handle and push the seat back forward or pull it backwards to the desired position e Push the seat back to be sure it is latched in position Storage Pull Frame Release Latch e With the legs all the way open lower the seat to position 1 the lowest position Fit the holes on the base tray latches onto the pegs on the e Pull the frame release latches forward and push the rear legs back of the high chair frame toward the front legs 15 Care e The pad and headrest are machine washable Wash the pad and headrest separately in cold water on the gentle cycle Do not use bleach Tumble dry separately on low heat and remove promptly The frame and base tray may be wiped clean using a mild cleaning solution and a damp cloth Do not immerse the base tray The food trays are dishwasher safe Simply remove the food tray from the base tray and place in your dishwasher To remove the pad e Remove the four elastic loops from the pegs on the underside and back of the seat e Unfasten the pad strap and headrest strap from the seat back e Feed the shoulder portion of the waist shoulder belts through the slots in the seat back the pad and the headrest e Feed the waist portion of the waist shoulder belts and crotch belt down through the slots in the seat
11. the waist belt e Repeat this procedure to loosen the other waist belt To change shoulder belt slots e From the back of the high chair push the shoulder portion of the waist shoulder belts through the seat back slots Hold _ Adjuster Slide Pull Strap Adjuster Tighten Loosen To tighten the shoulder belts Hold the adjuster and pull the front shoulder strap down To loosen the shoulder belts Slide the adjuster down e From the front of the high chair pull the shoulder portion of Note After adjusting the restraint system to fit your child the waist shoulder belts out and then fit them back through make sure you pull on it to be sure it is securely fastened the desired shoulder belt slots in the headrest pad seat pad and the seat back Pull on the belts to be sure they are secure in the seat back 11 Using the Trays WA R N N G Hint The base tray can be adjusted for your child s comfort two ways see steps 7 and 8 Prevent serious injury or death from falls or sliding out The child should be secured in the high chair at all times by the 22 A ie a ra restraining system either in the recline semi recline or upright position The restraint belts must be adjusted to fit your child snugly The tray is not designed to hold the child in the chair Release Bar Base Tray econ 22n 7 s e While pushing the release bar on the fr
Download Pdf Manuals
Related Search