Fisher & Paykel RH900CQ User's Manual
Contents
1. suit the dimension required fit black plastic extrusion to the base of the chimney and cut to length G Mounting screws and plastic cover caps are applied on top and bottom of the chimney 104385 Issue A DEG QRATI VI nod ISCREW COVER2. partial vacuum in the room This includes gas hobs A partial vacuum in the room could result in too high a concentration of gas in the atmosphere The appliance is supplied with an approved power cable which must not be changed If the supply cord of this equipment is damaged it must only be replaced by the manufacturer or its service agent or similarly qualified person in order to avoid hazard Particular care must be taken with grease filters which must be periodically cleaned at least every two months Remove the grease filters and wash them either by hand or in the dishwasher using mild detergent Use lukewarm water and mild detergent to clean stainless steel components In high humidity and coastal environments cleaning should be carried out frequently CAUTION Never use products containing abrasive liquid cleaners etc USE Care and attention should always be taken when cooking with oils alcohol etc which give off flammable vapours Pre used oil is especially dangerous in this respect Do not use uncovered electrical grill To avoid possibk risks of fire always comply with the maintenance instruction above When making the electrical connection check that the socket has an earth connection and that the voltage values correspond to those indicated on the rating plate inside the appliance The power socket connection is to be easilly accessible after installation CONTROL PANEL gy Left Push Button Fan Off D i
3. Lamp Replacement a SWITCH OFF THE POWER TO THE RANGEHOOD b USE A SMALL BLADE SCREWDRIVER INSTALLATION INSTRUCTION TO PRISE OFF THE LIGHT COVER Ci NOTE SLOT 87764 APEX MODEL c USE A CLOTH TO REMOVE THE BULB RHS00CQ DO NOT TOUCH THE BULB WITH FINGERS d REPLACE WITH A NEW BULB AND SNAP THE COVER BACK IN PLACE e HALOGEN BULB 12Volt 20Watt Parts a Service FILTERS Aluminium Filter No R104163 Ducted models Charcoal Filter No R104165 Recirculation models The use of charcoal filter is recommended on recirculating model rangehoods RECIRCULATING KIT 1752 Kits include Charcoal Filters 150 Flexible ducting Cable Ties 2 Top Guide Three filters For other Accessories Parts or Service please contact your local supplier Refer to the Warranty Certificate PRODUCT DIMENSIONS WARNING This appliance is not intended for use by young children or infirm persons without supervision eYoung children should be supervised to ensure that they do not play with the appliance There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels eYou must read the details concerning the method and frequency of cleaning There is a fire risk if cleaning is not carried out in accordance with the instructions Do not flamb under the rangehood Exhaust air must not be discharged into an existing flue which is used for exhausting fu
4. Second Push Button Fan On Low Speed Third Push Button Fan On Second Speed Fourth Push Button Fan On High Speed I Fifth Push Button Light On Off Switch INSTALLATION OF UNIT Read in conjunction with the following diagrams The unit is designed for 2 4 to 2 65 metre high ceiling The decorative chimney cover is telescopic and is designed for 665 to 950mm adjustment Note Ducting accessories are not supplied Please refer to the optional ducting kits The air outlet from the motor requires 150mm round ducting which requires 160mm diameter round hole in the ceiling This hole will he covered by the decorative chimney Care should be taken to align canopy with decorative chimney allowing sufficient clearance to accommodate the flexible ducting Before starting assembly read the Instructions carefully and remove the filters from canopy to allow access to wall mounting holes To remove the filters push the relative catch inward and tilting it downwards until it disengages from the supports Reverse these instructions when refitting the filters NOTE Stainless steel is very easily damaged during installation if abraided or Knocked b S INSTALLATION OF THE UNIT DUGTING SE TION N A7 E TON NA aA 2 4 TO 2 65 METRE HIGH C CEILING oe H UNDERSIDE OF HOOD TO COOKING SURFACE e RECIR SULATING DUCTING WARNING The distance between the hob and the mounting holes of the canopy to be at least 900mm to ensure that the fully in
5. mes from appliances burning gas or other fuels The minimum distance between the hob surface and the lowest part of the rangehood is 600mm This distance shall be at least 650mm recommended 700mm if the rangehood is installed over a gas hob Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air is fulfilled elf the supply cord of this equipment is damaged it must only be replaced by the manufacturer or its service agent or similarly qualified person in order to avoid a hazard 1064 nax Electrical Rating 295W 1 23A Max at 240V 50Hz g RANGEHOOD BUSTING All Dimensions in mm RECOMMENDED DUCTING SYSTEMS 104385 Issue A FOR RANGEHOODS CANOPY OPERATION Thank you for purchasing a quality stainless steel canopy rangehocd We have a high standard of quality control and each rangehood is tested and approved before it leaves the factory IMPORTANT Please read prior to installation or operation Always switch power off prior to installing servicing or cleaning the appliance Never use the appliance without filters Please read the notes on general cleaning especially the filters Exhaust air must not be discharged into a heating flue or wall cavity unless the cavity is designed for that purpose Areas where the rangehood is installed that also have gas oil or coal fired heaters must be well ventilated to prevent a
6. stalled canopy has a clearance of 700mm recommended height between the lower part of the hood and the cooking hob Before drilling any holes check the wall and the ceiling are clear of any electrical cables pipes etc Fixing to a solid stud is recommended T 4 Fix the mounting washers in position shown in diagram 1 Check with spirit level accross the washers to ensure they are level INSTALLING DUCTING NOTE All ducting must comply with local requirements and building codes Mark the position of decorative chimney at ceiling and wall cut cornice moulding away if necessary to enable panels to fit fat against the wall and ceiling 2 Mark and cut the hole in the ceiling to fit the ducting 155 to 160mm dia 3 This is positioned centrally with the canopy and 100mm from the wall INSTALLING CEILING BRACKET Using the supplied screws fix the ceiling bracket 4 to the wall checking that it is aligned with the hood CUT CORNI ce TO GLEAR ae IF a z 28 a KEYHOLES IN REAR OF CANOPY SHOWN DOTTED FIX SAFETY SCREW AFTER MOUNTING CANOPY FINAL ASSEMBLY Remove protective plastic covering from all parts ncluding filters Now fit the canopy an the fixed mounting washers Plug in power cord at power supply Check function of rangehood light and motor before continuing assembly Fix safety screw 5 connect 150mm ducting6 to top of motor flange secure with cable tie Assemble the telescopic ducting covers chimney 7 to accurately
Download Pdf Manuals
Related Search