Fisher & Paykel BI602CTE User's Manual
Contents
1. 20 mm plastic wiring card gt 16 20 mm L ili 600 mm BI452 series Compact Built In Oven BI602XC series Built In Oven Microwave Combination 70 mm min clearance gt Top View Top View 570 mm MIN 570 mm MIN 20 sz 20 16 20 mm L ili 16 20 mm 600 mm 600 mm2. OVEN 5 E n KUU UU Cu OVEN OVEN Y a a A a 5 A n A E E LO au Woy SINGLE OVEN DOUBLE OVEN COMBINATION OVEN BI602 series Single Built In Oven Na 8 S m Es gt De 578 mm i A 595 mm Top View 20 mm L 16 20 mm L T 600 mm I 570 mm MIN BI602ED series Double Built In Oven em E b E D E amp E LO 460 MIX B Mi L pm ern cpl mmp owet or gt Top View 570 mm MIN 16 20 mm j BI602CTE series Built In Oven Cooktop Combination Benchtop Detail Benchtop 20 mm 55 mm CookTop Cutout Gap m f OVEN ae see cooktop installation instructions p n 599100 Cooktop Installation 1 Remove the brackets from the cooktop 2 Place the cooktop in the cutout and secure p using the brackets previously removed 3 Feed the cooktop wiring harness out through the oven cavity 4 Remove the oven connector block cover on the oven top wiring cover 5 Connect the cooktop wiring harness lining the numbers letters on the harness with the numbers letters on the oven connector ock Leave plastic wiring card attached for future reference o 6 Clamp the wiring harness with the wiring clamp on the oven top wiring cover 7 Replace the oven connector block cover Top View 8 Install the oven as described on page 2 lt harness detail oven connector o TS
3. Fisher8Paykel innovative living Installation Instructions NZ AU Installation Information oO BI452 series BI602 series Built In Compact Built In Oven Oven pp O000 BI602CTE series Built In Oven Cooktop combination 0000 em A SS BI602ED series BI602XC series Built In Double Built In Oven Oven Microwave combination 541768C 10 2004 NZ Warnings and Safety information A WARNING Cut Hazard Take care panel edges are sharp Failure to use caution could result in minor injury or cuts A CAUTION In order to avoid hazard these products must be installed according to these instructions Please follow installation information carefully If in doubt consult your local building authority by laws Failure to install the product correctly could invalidate any warranty or liability claims The product is to be installed only by an authorised person IMPORTANT Please make this information available to the person responsible for installing the product as it could reduce your installation costs The cavity must be a completely sealed box with no gaps This will ensure the cooling air flows under the product and through the oven frame to give the correct venting and cooling for the oven and cabinet surround Failure to seal cavity box may cause distortion of su
4. rrounding cabinetry Read these instructions carefully before installing or using this product Before you start Ensure a suitable disconnection switch is incorporated in the permanent wiring mounted and positioned to comply with the local wiring rules and regulations A means of disconnection with at least a 3mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules unless he local wiring rules allow for the following variation A means of disconnection from he supply having an air gap separation in all active phase conductors must be incorporated in to the fixed wiring Ensure that the location of the oven connection socket is outside the installation space if the product is flush to the rear wall Ensure the benchtop and the oven cavi square and level y are Ensure the electrician provides sufficien free length of mains cable to reach from the bottom rear of the cavity to at least 1 5 metres in front of the bottom edge of the opening The cable may enter the cavity from the side op or bottom but top entry must be at the rear of the cavity Use easy to clean finishes for the wall surfaces surrounding the oven and cooktop to aid in removal of any cooking fume staining resulting from the use of the oven and cooktop Check the height from the floor suits the user Ensure that drawers and doors will be clear of obs
5. truction when fully opened Installation Instructions Installation instructions 1 Check that the oven cavity is square and within the limits in the installation dimensions 2 Remove the mains wiring access cover 3 Connect the mains wiring and replace the access cover 4 Remove the oven door and accessories lift and slide oven into place When installing the oven it is essential to centre the product in the cavity giving a spacing of 2 5mm from the door edge to the joinery 5 Secure oven in cavity using the four wood screws and washers supplied through the enamelled frame at either side of the oven as shown in the flush fitting installation options 6 Test then refit the door and accessories check that the oven is firmly secured in the kitchen unit Installing a cooktop above an oven If installing a cooktop above the oven ensure adequate clearance is provided for the cooktop as per the Cooktop Manufacturers Instructions Flush fitting installation options 20mm gie a gi 2 5 mm CUPBOARD FRONT l 20 mm ae DRAWER FRONT Height recommendation guide Figures are based on an average height of 1650mm 5 5 wearing shoes The height of the product may vary according to the height of the most frequent user 1650mm Average Height 595mm Oven 810mm Oven Base INSTALLATION Sooo f 8 OVEN
Download Pdf Manuals
Related Search