Fisher & Paykel GC9002 User's Manual
Contents
1. Email customer care fp com au SINGAPORE 150Ubi Avenue 4 02 00 Sunlight Building Singapore 408825 Tel 65 5470100 Fax 65 5470123 Email customerservice fisherpaykel com sg2. GC600 GC9002 CG901M Width 578mm 914mm 914mm Depth 511mm 533mm 546mm Height 40mm 40mm 76mm Note Height measurement below bench surface GC600 GC9002 CG901M A Width 560 564mm 846 882mm 860 895mm B Depth 485 495mm 478 501mm 486 524mm C Side Clearances 140mm 140mm 118mm D Rear Clearance 100mm 100mm 120mm E Entry from Side 50mm 50mm 25mm F Entry from Back 30mm 30mm 25mm G Clearance Below 60mm 60mm 81mm Bench Minimum clearance for cutout to combustible surface Manifold Centre Line A When used with a flexible hose the connector on the wall should be between 800mm to 850mm above the floor and in the region outside the width of the appliance to a distance of 250mm This should be accessable with the appliance installed Clearances RANGEHOOD CLEARANCE Dimension A See A G A 601 5 12 1 6 Dimension A Measured from the plane of the pan supports to Rangehood should not be less than 650mm Any other downward facing combustible surface less than 600mm above the highest part of the hob shall be protected for the full width and depth of the cooking surface area However in no case should this clearance to any surface be less than 450mm SIDE CLEARANCE Dimensions B amp C Where Dimension B measured from the periphery of the nearest burner to any vertical combustible surface is less than 200mm the surface shall be protected in accordance with Clause 5 12 1 2 to a Height C of not less than 150mm above
3. the hob for the full dimension width or depth of the cooking surface area Do use easy to clean finishes for the wall surfaces surrounding the cooktop to aid removal of any cooking stains resulting from use of the cooktop A G A Clause 5 12 1 2 A G A Clause 5 12 1 2 Protection of a Combustible Surface Near a Cooking Appliance The protection required by clause 5 12 1 1 shall ensure the surface temperature of the combustible surface does not exceed 50 C above ambient Note The fixing of 5mm thick ceramic tiles to the surface or attaching fire resistant materials to the surface and covering with sheet metal with a minimum thickness of 1 4mm would satisfy this requirement CLAMPING DOWN THE COOKTOP HOB Place the cooktop into the cutout and tighten it with the supplied clamps DO NOT OVER TIGHTEN The clamps will cope with bench thickness 15 50mm see diagram when used in the two orientations Gas Supply GAS SUPPLY CONNECTION The product is supplied set up for Natural Gas This cooktop is suitable for installation with Natural Gas or LP Gas Refer to table for the relevant pressures and appropriate injector sizes Gas connection to the product must use the elbow supplied The regulator will not seal if installed without it Ensure the blue washer supplied is located between the elbow and the product inlet Failure to use this will cause the product to leak AFTER INSTALLATION MAKE SURE ALL
4. CONNECTIONS ARE GAS SOUND Blue Washer FLEXIBLE HOSES Flexible hose assemblies should be AS NZS 1869 Class B or Class D certified Flexible hoses should not be exposed to temperatures exceeding their certified value They should not touch hot surfaces on the cooktop or neighbouring products Flexible hoses should not be subject to abrasion kinking or permanent deformation FOR LP GAS MODELS For LPG Models the gas supply for the appliance must be regulated to a pressure of 2 72kPa 11 WG See below for conversions FOR NATURAL GAS MODELS For NG Models the gas supply is connected to the regulator which is supplied loose with a built in test point 1kPa 4 WG and the inlet connection of 1 2 B S P male thread Do not over tighten The test point pressure should be preset to 1 0 kPa with the wok and semi rapid burners operating at maximum GAS SUPPLY CONNECTION CHECK To enable the gas supply to be readily shut off the gas supply must be connected with an isolating valve close to the product After installation and making all connections check thoroughly for possible leaks 1 Turn all control knobs on the unit to off position 2 Open the valve on the gas supply 3 Using a suitable leak testing solution e g Rocol check each gas connection one at a time by brushing the solution over the connection 4 The presence of bubbles will indicate a leak Tighten the fitting and recheck for leaks Ensure t
5. Fisher amp Paykel NEW ZEALAND AUSTRALIA and SINGAPORE INSTALLATION INFORMATION For GC600 GC9002 CG901 SERIES GAS COOKTOPS IMPORTANT INFORMATION Read the instructions before installing or using this product Please make this information available to the person responsible for installing this cooktop as soon as possible it could reduce your installation cost These products are registered in New Zealand at www ess govt nz and in Australia with AGA at www gas asn au CAUTION In order to avoid a hazard these products must be installed according to these instructions for installation Please follow installation information carefully If in doubt consult your local building regulations local gas authority codes and electrical regulations Failure to install the appliance correctly could invalidate any warranty or liability claims and lead to prosecution The product is to be installed only by a person aurthorised to work on gas installations This appliance shall be installed in accordance with the installation requirements of the local gas authority or the appropriate installation code issued by the A L PG A and A G A Reference Code AGA 601 or the Building Authorities requirements Particular attention shall be given to the relevant requirements regarding ventilation Take care of sharp edges when handling stainless steel products When this product is installed it shall not be used as a space hea
6. he blue washer supplied is located between elbow and manifold 5 Turn on each gas valve and light each burner 6 Check for a clear blue flame without yellow tipping If burners show any abnormalities check that they are located properly and in line with injector nipple Check correct orifices are installed 7 The operation of the appliance including the ignition system must be tested before leaving If after following the instructions given satisfactory performance cannot be obtained contact the local gas authority or your local Approved Service Agent for advice and assistance GAS RATE SUMMARY Your product is factory set for Natural Gas but may be converted to LPG use See overleaf Refer to the chart below for ratings BURNERS LP Gas Injector MJ h Orifice 2 75kPa Natural Gas Injector MJ h Orifice 1 kPa GC 9002 series Semi Rapid Burner LH amp RH Rear Aux Burner RH Front Fish Burner Centre Wok Burner LH Front 7 9MJ h 3 7MJ h 10MJ h 15MJ h 7 9MJ h 4 1MJ h 10MJ h 15MJ h GC 600 Series Semi Rapid Burner LH amp RH Rear Aux Burner RH Front Wok Burner LH Front 6 1MJ h 3 7MJ h 15MJ h 6 4MJ h 4 1MJ h 15MJ h CG 901 M Semi Rapid Burner LH Rear Simmer Burner RH Front Rapid Burner LH Front RH Rear Wok Burner Centre 6 1MJ h 3 2MJ h 6 4MJ h 3 2MJ h 7 9MJ h 15MJ h 8 4MJ h 15MJ h The data plate information can be found in the duplica
7. should be placed over the existing gas type label to indicate the change This has been set at the factory for NG but can be checked after the correct pressure has been reached To adjust the minimum setting you will need a 2 5 x 45 screwdriver 1 Remove the knob 2 Ignite the burner and set the knob to its minimum position 3 Rotate the turn down screw down the hole in the valve spindle Rotate slowly until a minimum regular flame is achieved The flame will diminish when the screw is turned clockwise and increase when turned anti clockwise 4 When the setting is right check regulation by quickly rotating the knob from the maximum to the minimum delivery position The flame must not go out 5 Replace the knob Before you call for service or assistance Check the things you can do yourself Refer to your User Guide and check 1 Your product is correctly installed 2 You are familiar with its normal operation If after checking these points you still need assistance please call your Fisher amp Paykel retailer who is trained to provide information on your product or if we can be of any further help please contact our Customer Care Centre NEW ZEALAND P 0 Box 58732 Greenmount Auckland Toll Free 0800 FP CARE 0800 37 2273 Fax 09 273 0656 Email customer care fp co nz AUSTRALIA P O Box 798 Cleveland OLD 4163 Toll Free 1300 650 590 Tel 07 3826 9100 Fax 07 3826 9298
8. te data plate which should be placed on an accessible surface adjacent to the cooktop Adjusting the Cooktop MINIMUM SETTING OR TURN DOWN Customer Support CONVERSION TO DIFFERENT GAS TYPE Burners can be used with NG or LPG provided that the injector orifices appropriate for the gas delivered are installed To change the injector orifices you will need a 7mm box spanner and a 10mm ring spanner CG901M only 1 Turn off the main electrical supply WARNING Shock Hazard Inside 2 Ensure all gas valves are turned off 3 Remove all trivets and burner heads 4 Pull off knobs 5 Unscrew the nut securing the flame failure probe of the mini auxiliary burner 6 Remove the 2 screws holding each burner 3 on the wok burner 7 Partially lift the hob and unplug the electrode on the mini auxiliary burner to allow hob removal Caution The edge can be sharp l CG901M on 8 Unscrew the orifices and replace them with the correct ones size numbers are stamped on the side eg 70 0 70mm 9 Reset the venturi position aligning the end K of the venturi tube with the edge of the slot K AN in the bracket below it Outermost position f a for LPG innermost for NG see figure right Some fine adjustment may be required for local conditions 10 To replace the CG901M hob repeat steps 1 7 in reverse CG901M only 11 Reset the minimum setting see next column The label supplied with the orifices
9. ter especially if installed in boats or caravans No combustible material or products should be placed on this product at any time Do not spray aerosols in the vicinity of this product while it is in operation This product should not be sealed into the bench with silicon or glue This will make future servicing difficult Fisher amp Paykel will not be liable for costs associated with releasing such a product nor for repairing damage that may be incurred in doing this BEFORE YOU START DO Prior to installation ensure that the local distribution conditions nature of gas and pressure and the adjustment of the product are compatible DO Ensure a suitable disconnection switch is incorporated in the permanent wiring positioned to comply with the Local Wiring Rules and Regulations DO Ensure the benchtop is square and level and ensure no structural members interfere with space requirements DO Ensure that there is a 3 pin socket outlet within reach of the cooktop cable 900mm from rear right of product this should be accessible after installation The mains cable should not touch any hot metal parts DO Make the benchtop of a heat resistant material CURRENT INFORMATION Current Installation Instructions Product dimensions and specifications are available on the Fisher amp Paykel web site www fisherpaykel com Includes Quantum Models Part No 530451 D February 2003 Dimensions PRODUCT DIMENSIONS
Download Pdf Manuals
Related Search