Fisher & Paykel DD36SDFTX2 Installation Guide
Contents
1. V wall mounted Ensure drain hose is routed straight to joiner Remove excess drain hose material if necessary Do not shorten the inlet hose 1 CONNECT INLET HOSE TO HOT WATER SWITCH PRODUCT ON Tighten coupling with wrench a gaa G Ensure the x 180 pp iea ru t er washer is No leaks fitted inside pag et i cae the coupling 1 N 4 7 Important Ensure that drain connection will comply with local plumbing regulations 19 3 FINAL CHECKLIST M 0O O O OO ogo Check all parts are installed Ensure product is level securely fastened to the cabinetry and opens and closes freely The drawer must be free to fully close with no resistance from the cabinetry Ensure inlet hose to water supply has supplied rubber washer fitted and that it s tightened a further half turn after seal contact Ensure any knockouts or plugs in drain connection have been drilled out and drain connection has been made The drain hose joiner must not support the weight of excess hose material Keep drain hose as fully extended as possible to prevent sagging Any excess length of drain hose should be kept on the dishwasher side of the highloop If connecting the drain hose to the sink trap ensure the Highloop is a minimum 6 150 mm higher than the drain hose joiner Ensure any packaging or tape securing the racks is removed2. Important Ensure correct chassis position In order for product to function cabinetry must not block the drawer front from closing hard against the chassis Minimum clearances from adjacent cabinetry min 2 13 mm clearance from a min Ye 2 mm corner cupboard O o emne 7 to adjacent cupboard door p 16 U SJS JS INTEGRATED MODELS ONLY CUSTOM FRONT PANEL CALCULATIONS FRONT PANEL SPECIFICATIONS min Ye 2mm 3 1346 16 20 mm panel thickness i Maximum weight of panel 20 Ib 9 kg iy Adequately sealed to withstand moisture 122 F 50 C 80 RH lz Because of it being a hot and wet environment generally the back and sides of the panel should be completely sealed with a waterproof vapor barrier ie polyurethane to prevent damage to the panel The back of the panel including any integrated handle should be P completely flush so that the seal between the panel and the rubber trim is maintained A H n gt min e 2mm min e 2mm _ The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry WIDTH OF PANEL min Ye 2mm WIDTH OF THE PANEL HEIGHT Measure A the width between adjacent door drawer fronts OF PANEL and write it in the first box below then complete the equation clearance to adjacent cabinet front WIDTH OF PANEL min Ye 2 mm min 33 1 6 855 mm min Ye 2mm ventilation
3. fixing holes either side on the bottom use 12 38 mm fixing screws amp washers two pairs of formed brackets on either side of the chassis use 3 16 mm screws 4p INTEGRATED ONLY SECURE THE EXTERNAL VENT After routing the vent hose ct gt through and out the hole cutout attach and secure the vent by tightening the four Air screws provided low INTEGRATED MODELS ONLY INSTALLING THE FRONT PANEL 16 REMOVE BRACKET FROM PRODUCT N WARNING Electrical Shock Hazard Before continuing ensure that the product is disconnected from the power supply Failure to follow this warning may result in electrical shock injury or fire A WARNING Electrical Shock Hazard To ground earth the panel bracket connect the ground earth wire from the product to one of the tabs Any custom metal compo nent e g handle that extends past the rubber door seal must be grounded earthed too Failure to follow these warnings may result in electrical shock injury or fire 6 ATTACH PANEL TO PANEL BRACKET Important Use all 14 screws provided as shown 58 16 mm 4 Align bottom of panels with bottom of brackets Important Ensure the rubber seal between the drawer and panel is kept in place We recommend pushing the drawer runners back 4 100 mm before attaching the panel Once the panel is fiited ensure the runners are
4. INSTALLATION INSTRUCTIONS DishDrawer dishwasher DD36SDFTX2 Designer amp DD36STI2 Integrated models US CA Fisher amp Paykel 590208D 04 13 SAFETY AND WARNINGS A WARNING Electrical hazard Before installing the dishwasher remove the house fuse or open the circuit breaker If permanently connecting the dishwasher be sure the power is isolated and the dishwasher unplugged GROUNDING INSTRUCTIONS This appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded If the dishwasher is installed as a permanently connected appliance GROUNDING INSTRUCTIONS This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the appliance Do not modify the power supply plug provided with the
5. INTEGRATED MODELS ONLY PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINET Services can be located either side of dishwasher VENT HOSE NW 2 N NU N mm F DRAIN HOSE INLET HOSE POWER CORD Important To prevent pooling of condensation from the vent hose a toekick height of no less than 4 100 mm is required The 2 3 60 mm services hole for the hoses should be enlarged to accomodate the extra venting hose by cutting out some material Services can be located from the bottom corner either side of dishwasher __ VENT HOSE DRAIN HOSE INLET HOSE If the services holes are through metal ensure you fit the supplied Edge Protector around the hole for the O power cord Important To prevent pooling of condensation from the vent hose a toekick height of no less than 4 100 mm is required W W ww Y G max 172 38 mm i E A so POWERCORD eee mm p lt f External Venting kit 1 Shelf cutouts i max 346 5 mm 8 16 220 mm 4 100 mm External Venting kit 1 Shelf cutouts max 346 5 mm Qt 234 60 mm i 16 220 mm BE 4 100 mm MAXIMUM DISTANCE OF HOSES amp CORD FROM CHASSIS EDGE ii Left hand side Right hand side Drain hose 78 1 2 2000 mm Drain hose 59 46 1500 mm Inlet hose 64 34 1650 mm Inlet hose 37 3
6. appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician Do not use an extension cord adapter plug or multiple outlet box Failure to follow this advice may result in electrical shock or death A WARNING Very Heavy A WARNING Cut hazard Take care panel edges are Do not attempt to lift this sharp product unassisted Lifting unassisted may cause serious injury Failure to use caution could result in injury or cuts IMPORTANT SAFETY INSTRUCTIONS Installation of this dishwasher requires basic mechanical and electrical skills Be sure to leave these Instructions with the Customer Installation must comply with your local building electricity and plumbing regulations At the completion of the dishwasher installation the Installer must perform the Final Checklist Remove all packaging materials supplied with the dishwasher This dishwasher is manufactured for indoor use only Ensure all water connections are turned OFF It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations The dishwasher MUST be installed to allow for future removal from the enclosure if service is required The switched power outlet must be outside the dishwasher cavity so that it is accessible after installation Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply co
7. ct in pull through hoses and P cord ensuring they don t get kinked or twisted Important Important Ene correct chassis position In order If product cannot be pushed in far enough pull for product to function cabinetry must out again and rearrange hoses and cord Do not not block the drawer front from closing use excessive force as doing so may squash the hard against the chassis hoses and lead to incorrect operation 1B REMOVE THE DRAWER Product may move Mark chassis position on cavity J To prevent kinked hoses we recommend rotating the drawer anti clockwise and f resting it on its side KEYAT after removal Press the release tabs in on either side and push back to release drawer from runners Push drawer runners back in REFIT THE DRAWER ONTO THE RUNNERS T lt a lease tabs lt he re tgr 100 mm Ensure the drawer is now rotated clockwise back d iI forwar k poth side a _ A Before refitting the drawer ensure the hoses are not twisted and the latches at the rear of each drawer Ensure the release tabs on both sides are reset fully 28 SECURE THE DRAWER TO THE CABINETRY The product has three pairs BA of fixing points Refer to 2 PARTS SUPPLIED for relevant parts Ensure the sound insulation is repositioned correctly a pair of
8. d Open drawer auto power on may need to be turned on Water around water supply and drainage connections Check connections existing plumbing and hoses for leaks Check rubber washer and hose clamp are correctly fitted If product is tipping Ensure the product is secured to the cabinetry If front panels are misaligned Check and relevel product Check the cabinetry is square Check and adjust front panel alignment if necessary Drawer doesn t close properly Ensure nothing is obstructing the drawer from closing properly eg sound insulation hoses or drawer latches Ifa problem occurs consult the Troubleshooting or Fault codes section of the User guide If after checking these points you still need assistance please refer to the Service amp Warranty book for warranty details and your nearest Authorized Service Center or contact us through our website listed below Important SAVE THESE INSTRUCTIONS The models shown in this document may not be available in all markets and are subject to change at any time For current details about model and specification availability in your country please visit our website listed at the end of this document or contact your local Fisher amp Paykel dealer www fisherpaykel com
9. duct cannot be pushed in far enough pull for product to function cabinetry must out again and rearrange hoses and cord Do not not block the front panel from closing use excessive force as doing so may squash the hard against the chassis hoses and lead to incorrect operation Ga INTEGRATED ONLY SECURE THE EXTERNAL VENT yo s X After routing the vent hose L gt through and out the hole cutout attach and secure the vent by tightening the four Airg screws provided low 2a SECURE THE DRAWER tl D Open the drawer halfway SD g 1 Using a flat bladed D screwdriver prise the gray Replace the gray rubber plug back into the trim moulding and ensure the trim seal is facing forward EQ rubber plug out of the trim moulding Using a small Philips screwdriver screw through the trim moulding securing the side mounting bracket to the cabinetry Do not damage the rubber trimseal Repeat for all GA four brackets 14 ALTERNATIVE METHOD b SECURE BY DRAWER REMOVAL INTEGRATED ONLY ATTACH VENTING HOSE Check that the fitted elbow is rotated left or right depending on the direction of the routing then ensure the venting hose is securely attached to it Q 08 PULL THROUGH HOSES amp MOVE INTO THE CAVITY Vent Hose Integrated models only aT quanti lI W vent either through same cabinet or adjacent 3 pone tens As you push produ
10. from the drawer Turn on the power and water supplies then open the drawer You should hear a beep and see a program indicator light up on the internal control panel Check the spray arms are in place and free to rotate Spray arms Add three cups of water into the drawer Press amp on the internal control panel until the indicator of the Rinse program lights up Close the drawer and press bil to start the program After the Rinse program has finished ensure the dishwasher has run and drained correctly Check water supply and drainage connection for leakage TROUBLESHOOTING Excessive water remaining above the filter plate after the rinse cycle Check for a kinked drain hose or blocked waste connection highloop not properly installed or drain hose not routed correctly a No water supply This is displayed as a U1 fault see section If there is a fault in the User guide for how to recognise this fault on models without a display Check water is connected and turned on The dishwasher is beeping continuously There is a fault See section If there is a fault in the User guide for further information and instructions No program indicator lights up when the drawer is opened Ensure power is connected and is switched on If it is and still no indicator lights up see the Preference options section of the Quick start guide An option calle
11. fully back into position and the release tabs on both sides are reset fully When refitting the door pins ensure they are orientated as shown ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS or 6 2mm aI i YIN Insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the panel up or down to align the gaps in your cabinetry Repeat on the other side if necessary The panel has a maximum travel of 46 2 mm up or down Important Integrated models Ensure that you maintain a minimum of 6 2 mm ventilation gap below the panel Designer models Ensure you maintain a minimum of 6 8mm ventilation gap below the panel 17 0 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS CHOOSE WHICH IS MORE SUITABLE 8 Dishwasher and Standpipe 1 38 mm Dishwasher using Air Break with Drain Hose Joiner Dishwasher using sink trap with drain hose joiner A If space is limited gt for fixing push es hose through drain lt hose support ff to required height t If space is limited S t for fixing push S hose through drain hose support to required height Supplied drain hose joiner 34 19 mm waste tee 4 29 2 34 34 750 882 5 mm 29V 34 750 882 5 mm N 1 G 38 mm 37 3 950 mm Max height to top of Air Break countertop or 1
12. gap with external venting kit installed aa ea HEIGHT OF THE PANEL Measure B and write it in the first box below then complete the equation min 146 2mm ventilation gap with external venting kit installed i i ventilation gap HEIGHT OF PANEL min 16 2 mm Ea a b Note when the top of the dishwasher has to be lower than the adjacent cabinetry the panel can be increased in height 6 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION 6a REMOVE THE DRAWER A Product may move Mark chassis position on cavity EMAI To prevent kinked hoses we Y HH recommend rotating the drawer Arriba counter clockwise and resting it on its side after removal INA 2 AA Access cover Press the release tabs in on either side and push back to release drawer from runners 6c TERMINATE THE WIRING AS SHOWN Remove knock out for cable clamp and fit a suitable cable clamp for the conduit a 13 i N S NN C QN Use copper conductors only LS REMOVE THE ACCESS COVER amp POWER CORD co Before continuing ensure that the product is disconnected from the power supply Failure to follow this warning may result in electrical shock injury or fire Ensure the drawer is now oe clockwise bac Before refitting the drawer ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing fo
13. ncl front panel height overall width of product overall depth of product excl handle depth of chassis to back of front panel maximum extension of drawer excl handle depth of front panel excl handle height of chassis depth of handle height of front panel height of ventilation gap below front panel al l lizrlaln miolal gt height from top of handle to top of front panel Tincludes Ye 2 mm high bracket slots Assuming panel thickness of 16 18 mm 7XLIGS9ECG Jaubisaq 18 1346 478 35 4 895 22 2 571 21 34 553 21 6 545 6 18 18 4e 458 1 41 18 2 470 He 8 2 Y2 64 3Recommended for a 6 2 mm ventilation gap below front panel if cavity height is 18 7 480 mm ZILS9EAA pajeibaj u 18 1346 478 min 33 1 6 855 22 9 571 2 21 34 553 21 746 545 54 6 16 20 18 Yie 458 n a 18 34 476 min Ye 2 n a 4 CABINETRY DIMENSIONS Cabinetry dimensions inches mm iw By JS S2 height of cavity L from support surface to underside 18 7 480 of countertop M _ inside height of cavity 18 e 460 N _ inside width of cavity 34 864 O overall width of cabinetry 35 6 900 P _ inside depth of cavity min 22 46 560 Recommended ZILS9EAA 18 480 min 18 460 34 864 35 746 900 min 22 46 560 18 mm Ye 2 mm Ve 2 mm
14. rd and hoses If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage Make sure only new hoses are used for connection supplied with the dishwasher Old hoses should not be reused Failure to install the dishwasher correctly could invalidate any warranty or liability claims If the product is installed in a motor vehicle boat or similar mobile facility you must bring the vehicle boat or mobile facility containing the product to the service shop at your expense or pay the service technician s travel to the location of the product SAVE THESE INSTRUCTIONS T ADDITIONAL SAFETY AND WARNINGS INTEGRATED MODELS ONLY WARNING Electrical Shock Hazard WARNING To reduce the risk of electrical shock fire or injury to persons the installer must ensure that the dishwasher is completely enclosed at the time of installation Before fitting the front panel make sure that the dishwasher is disconnected from the power supply After installing the front panel the installer must ensure that the following components are electrically grounded the panel bracket and any custom metal component e g handle that extends past the rubber door seal Failure to follow these warnings may result in electrical shock injury or fire IMPORTANT SAFETY INSTRUCTIONS Read these instructions completely and carefully Ensure the product is not plugged in Installation of c
15. rward Ensure the release tabs on both sides are reset fully CAVITY PREPARATION These marks indicate formed bracket screw locations if securing by drawer removal If there is no side partition you can construct timber bracing as something to secure into Important Adjacent cabinetry must not extend above cavity base L L 16 2mm to O OS vz A be applied to the dishwasher cavity Ea 10mm Moisture Important protection The power outlet must be tape must located in a cabinet adjacent 110 120 VAC max 15 A max 172 Services can be located either side of the dishwasher Services hole Can be located either side of dishwasher preferably at the bottom of the cavity as shown If adequate clearance services hole can be made higher to clear toekick space If hole is higher ensure drain hose s are routed straight into the waste connection If the hole is through wood make sure its edges are smooth and rounded If the hole is through metal ensure you fit the supplied Edge Protector to prevent damage to the power cord 38 mm max 5 7 min 7 72 200 mm Water Connection Recommended HOT Maximum 140 F 60 C Supplied hose to suit 32 9 mm male compression fitting Water Pressure Water softener models Max 1 MPa 145 psi Min 0 1 MPa 14 5 psi Models without water softener Max 1 MPa 145 psi Min 0 03 MPa 4 3 psi
16. s 950 mm Power cord excl plug 29 12 750 mm _ Venting hose 49 1346 1265 mm ARAVAVVVALARARERRRRRRRRRERRREERRnnnnnnnnnnD Integrated models only Integrated models only Power cord excl plug 15 34 400 mm Venting hose 75 1346 1925 mm MALUULRLRRRRRRRRRRRRRRRRRERRRRRRRRRRRRRRERRRRRRRRRRnRnnEE 11 NOW CHOOSE WHICH INSTALLATION METHOD a or b IS MORE SUITABLE FOR YOUR CABINETRY RECOMMENDED METHOD a SECURE WITHOUT DRAWER REMOVAL FRAMELESS CABINETRY ONLY ATTACH SIDE MOUNTING BRACKETS oa INTEGRATED ONLY ATTACH VENTING HOSE Clip all four side mounting brackets into their slots using a flat bladed screwdriver Ensure they re securely fitted before sliding product into cavity Check that the fitted elbow is rotated left or right depending on the direction of the routing then ensure the venting hose is securely attached to it Q The mounting slots are in pairs one on each side diagonally across the product A bracket must match A slot and B bracket must match B slot ia PULL THROUGH HOSES amp MOVE INTO THE CAVITY E Vent Hose Integrated models only E immon M N vent either through same cabinet or adjacent cabinet as per step 7b or 7c As you push product in pull through hoses and cord ensuring they don t get kinked or twisted Important Important Ensure correct chassis position In order If pro
17. ustom panels requires basic mechanical and electrical skills Installation must comply with your local building and electricity regulations Failure to install the custom panels correctly could invalidate any warranty or liability claims SAVE THESE INSTRUCTIONS a PARTS SUPPLIED ALL MODELS yp Fx Drain hose Drain hose Wire clip 1 support 1 joiner 1 for securin Drain hose joiner Edge Protector 1 If the services hole is through a metal partition the hole must be protected with the Edge protector supplied to prevent damage to the power cord or hoses ee OG l Side mounting Clamp 1 Phillips 1 2 38 mm Rubber bracket kit for securing 54 16 mm bottom fixing washer for A and B 2 Drain hose joiner screws 7 screws amp metal inlet hose 1 OPTIONAL washers 2 e itte lf the Drain hose supplied is not long enough to reach your services you must use a Drain Hose Extension Kit P N 525798 which will extend the drain hoses by 11 10 3 6m The kit is available from the nearest Fisher amp Paykel Authorized Service Center or Toll free 1 888 936 7872 or www fisherpaykel com b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS External Venting kit 1 i Panel bracket 1 Panel mounting attached to product screws 14 Moisture protection tape 1 to prevent moisture damage G PRODUCT DIMENSIONS Product dimensions inches mm overall height of product i
Download Pdf Manuals
Related Search