Fisher & Paykel DD24SCB7 Installation Guide
Contents
1. the appliance is properly grounded If the dishwasher is installed as a permanently connected appliance GROUNDING INSTRUCTIONS This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the appliance Do not modify the power supply plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician Do not use an extension cord adapter plug or multiple outlet box Failure to follow this advice may result in electrical shock or death A WARNING Cut hazard Take care panel edges are sharp Failure to use caution could result in injury or cuts A WARNING Electrical Shock Hazard WARNING To reduce the risk of electrical shock fire or injury to persons the installer must ensure that the dishwasher is completely enclosed at the time of installation Before fitting the front panel make sure that the dishwasher is disconnected from the power supply After installing the front panel the installer must ensure that the following components are electrically grounded the panel bracket and any custom metal component e g handle that extends past the rubber seal Failure to follow these warnings may result in electrical shock injury or fire IMPORTANT SAFETY INSTRUCTIONS Installation of this dishwasher require2. INTEGRATED MODELS CAVITY PREPARATION amp EXTERNAL VENTING MAXIMUM DISTANCE OF HOSES amp CORD FROM CHASSIS EDGE 18 456 mm 18 480 mm CAVITY CAVITY 18 480 mm CAVITY ONLY ATTACH CAVITY BRACKET SECURE WITHOUT SECURE BY DRAWER REMOVAL DRAWER REMOVAL RECOMMENDED ALTERNATIVE METHOD a METHOD b FOLLOW STEPS FOLLOW STEPS FOR THE FOR THE EXTERNAL EXTERNAL VENTING KIT VENTING KIT Ll INSTALL THE FRONT PANEL l CHOOSE DRAINAGE OPTION l CONNECT TO WATER amp ELECTRICITY FINAL CHECKLIST TROUBLESHOOTING SAFETY AND WARNINGS ALL MODELS A WARNING Electrical hazard Before installing the dishwasher remove the house fuse or open the circuit breaker If permanently connecting the dishwasher be sure the power is isolated and the dishwasher unplugged GROUNDING INSTRUCTIONS This appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service representative if you are in doubt as to whether
3. When refitting the door pins ensure they are orientated as shown INTEGRATED MODELS ONLY INSTALLING THE FRONT PANEL 22 ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS t or ie 2 mm With the front panels fitted insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the panels up or down to align the gaps in your cabinetry Repeat on the other side if necessary The panel has a maximum travel of Ve 2 mm up or down Important Ensure that you maintain a minimum of 2 mm ventilation gap below the panel 19 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS CHOOSE WHICH IS MORE SUITABLE Dishwasher and Standpipe 1 38 mm If space is limited t for fixing push S hose through drain hose support to required height i 29 34 34 750 882 5 mm 37 38 950 mm Max height to top of Air Break countertop or wall mounted Dishwasher using Air Break with Drain Hose Joiner Supplied drain hose joiner 34 19 mm waste tee ishwasher usinq sink trap with drain hose joiner If space is limited for fixing push por hose through drain 7 NS hose support Z N to required height t 29734 94 750 882 5 mm HIGHLQOP min 6 150 mm Y min R8 200 mm CONNECT INLET HOSE TO HO
4. cabinetry Do not damage the rubber trimseal Repeat for all GA four brackets I 16 ALTERNATIVE METHOD b SECURE BY DRAWER REMOVAL e INTEGRATED ONLY ATTACH VENTING HOSE 39 PULL THROUGH HOSES amp MOVE INTO THE CAVITY Check that the fitted elbow is rotated left or right depending on the direction of the routing then ensure the venting hose is securely attached to it 0 I Vent Hose Integrated models only III WWW WW NS vent either through same cabinet or adjacent cabinet as per step 9a or 9b As you push product in pull through hoses and cord ensuring they don t get kinked or twisted Important If product cannot be pushed in far enough pull out again and rearrange hoses and cord Do not use excessive force as doing so may squash the hoses and lead to incorrect operation i SECURE THE DRAWER TO THE CABINETRY REMOVE THE DRAWER The product has three Product may pairs of fixing points move Mark chassis position on cavity Ensure the sound insulation is repositioned correctly To prevent kinked hoses we recommend rotating the drawer counter clockwise and resting it on its side after removal two pairs of formed brackets on either chassis side use 16 mm screws a pair of fixing holes on the bottom use 1 38 fixing screws amp washers Press the release tabs in on eith
5. correctly fitted If product is tipping Ensure the product is secured to the cabinetry If front panels are misaligned Check and relevel product Check the cabinetry is square For Integrated models check and adjust front panel alignment if necessary Drawer doesn t close properly Ensure nothing is obstructing the drawer from closing properly eg sound insulation hoses or drawer latches problem occurs consult the Troubleshooting section of the User guide If after checking these points you still need assistance please refer to the Service amp Warranty book for warranty details and your nearest Authorized Service Center or contact us through our website listed below Important SAVE THESE INSTRUCTIONS The models shown in this document may not be available in all markets and are subject to change at any time For current details about model and specification availability in your country please visit our website listed at the end of this document or contact your local Fisher amp Paykel dealer www fisherpaykel com
6. injury or fire Ensure the drawer is now rotated ise bac Before refitting the drawer ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward Ensure the release tabs on both sides are reset fully CAVITY PREPARATION These marks indicate formed bracket screw locations if securing by drawer removal If there is no side partition you can construct timber bracing as something to secure into Important Adjacent cabinetry must not extend above cavity base Important The power outlet must be located in a cabinet adjacent to the dishwasher cavity Moisture 110 120 VAC max 15 A 8 10mm protection tape must be applied Water Connection Recommended HOT Maximum 140 F 60 C Supplied hose to suit 38 9 mm male compression fitting Water Pressure Water softener models Max 1 MPa 145 psi Min 0 1 MPa 14 5 psi max 12 38 mm max 17 6 450 mm Services can be located either side of the dishwasher Sd Models without water softener Max 1 MPa 145 psi Min 0 03 MPa 4 3 psi min 7 7 amp 200 mm Services hole Can be located either side of dishwasher preferably at the bottom of the cavity as shown If adequate E clearance services hole can be made higher to clear toekick space If hole is higher ensure drain hose s are routed straight into the waste connectio
7. n a 5lsselD 17 78 454 23 599 22 4e 582 21 34 553 21 78 556 1 29 17 8 454 n a 17 14 438 Va 7 n a 5Recommended for a 2 mm ventilation gap below panel TALL HEIGHT MODELS 5 R D a 8 85 8 5 sin e SIRE 18 34e 478 17 amp 454 23 9Ae 599 23 94e 599 22 2 571 22 571 21 34 553 21 74e 545 Ye 18 17 7 454 1 41 18 2 470 He 8 2 2 64 21 34 553 21 74e 545 58 94e 16 20 17 7 amp 454 n a 17 94e 452 min Ye 2 n a 08 81 18 6 478 23 e 599 22 571 21 34 553 21 6 545 3 Y 1346 16 20 177 454 n a 18 34 476 5 min Vie 2 n a 5 CABINETRY DIMENSIONS 7 Cabinetry dimensions inches mm STANDARD HEIGHT MODELS TALL HEIGHT MODELS E o i 2 B i Bou g gt 3 83 8 58355 2 2 a ES zo ES SD 2 A 2 2398 L inside height of cavity min 16 4 412 min 164 412 min 16 4 412 18 456 18 74 480 18 456 18 74 480 M inside width of cavity 23 600 23 600 23 600 23 5 600 23 600 23 600 23 600 N inside depth of cavity min 22 560 22 560 min 22 560 min 22 146 560 22 e 560 22 e 560 min 22 ie 560 Minimum clearances from adjacent cabinetry Cavity height
8. INSTALLATION INSTRUCTIONS DishDrawer dishwasher DD24S 7 amp DD24ST 7 models US CA Fisher amp Paykel 590204D 04 13 1 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL Classic DD24SCX7 DD24SCW7 DD24SCB7 PARTS SUPPLIED PRODUCT amp CABINETRY DIMENSIONS STANDARD HEIGHT OPTIONALLY HARD WIRING CAVITY PREPARATION MAXIMUM DISTANCE OF HOSES amp CORD FROM CHASSIS EDGE SECURE WITHOUT SECURE BY DRAWER REMOVAL DRAWER REMOVAL RECOMMENDED ALTERNATIVE METHOD a METHOD b CHOOSE DRAINAGE OPTION CONNECT TO WATER amp ELECTRICITY FINAL CHECKLIST TROUBLESHOOTING STANDARD HEIGHT SINGLE MODELS Designer E DD24SDFX7 PARTS SUPPLIED PRODUCT amp CABINETRY DIMENSIONS STANDARD HEIGHT OPTIONALLY HARD WIRING CAVITY PREPARATION MAXIMUM DISTANCE OF HOSES amp CORD FROM CHASSIS EDGE SECURE WITHOUT SECURE BY DRAWER REMOVAL DRAWER REMOVAL RECOMMENDED ALTERNATIVE METHOD a METHOD b CHOOSE DRAINAGE OPTION CONNECT TO WATER amp ELECTRICITY FINAL CHECKLIST TROUBLESHOOTING Integrated 24517 PARTS SUPPLIED EXTERNAL VENTING KIT PRODUCT amp CABINETRY DIMENSIONS STANDARD HEIGHT OPTIONALLY HARD WIRING CUSTOM FRONT PANEL CALCULATIONS INTEGRATED MODELS CAVITY PREPARATION amp EXTERNAL VENTING MAXIMUM DISTANCE OF HOSES amp CORD FROM CHASSIS EDGE SECURE WITHOUT SECURE BY DRAWER RE
9. MOVAL DRAWER REMOVAL RECOMMENDED ALTERNATIVE METHOD a METHOD b FOLLOW STEPS FOLLOW STEPS FOR THE FOR THE EXTERNAL EXTERNAL VENTING KIT VENTING KIT INSTALL THE FRONT PANEL CHOOSE DRAINAGE OPTION CONNECT TO WATER amp ELECTRICITY FINAL CHECKLIST TROUBLESHOOTING Classic DD24SCTX7 DD24SCHTX7 DD24SCTW7 DD24SCTB7 PARTS SUPPLIED PRODUCT amp CABINETRY DIMENSIONS TALL HEIGHT l OPTIONALLY HARD WIRING CAVITY PREPARATION MAXIMUM DISTANCE OF HOSES amp CORD FROM CHASSIS EDGE SECURE WITHOUT SECURE BY DRAWER REMOVAL DRAWER REMOVAL RECOMMENDED ALTERNATIVE METHOD a METHOD b CHOOSE DRAINAGE OPTION CONNECT TO WATER amp ELECTRICITY FINAL CHECKLIST TROUBLESHOOTING TALL HEIGHT SINGLE MODELS Designer DD24SDFTX7 PARTS SUPPLIED PRODUCT amp CABINETRY DIMENSIONS TALL HEIGHT OPTIONALLY HARD WIRING CAVITY PREPARATION MAXIMUM DISTANCE OF HOSES amp CORD FROM CHASSIS EDGE ATTACH CAVITY BRACKET SECURE WITHOUT SECURE BY DRAWER REMOVAL DRAWER REMOVAL RECOMMENDED ALTERNATIVE METHOD a METHOD b L CHOOSE DRAINAGE OPTION CONNECT TO WATER amp ELECTRICITY FINAL CHECKLIST TROUBLESHOOTING Integrated DD24STI7 DD24SHTI7 PARTS SUPPLIED EXTERNAL VENTING KIT PRODUCT amp CABINETRY DIMENSIONS TALL HEIGHT OPTIONALLY HARD WIRING CUSTOM FRONT PANEL CALCULATIONS
10. OF HOSES amp CORD FROM CHASSIS EDGE Left hand side Right hand side Drain hose 78 12 2000 mm Drain hose 70 12 1800 Inlet hose 64 34 1650 Inlet hose 49 1250 mm Power cord excl plug 27 12 700 mm Power cord excl plug 29 2 750 mm Venting hose 60 1525 mm CE Integrated models only Integrated models only Venting hose 75 116 1925 mm AEO 1 DESIGNER amp INTEGRATED TALL MODELS FOR 18 78 480 mm CAVITY ONLY ATTACH CAVITY BRACKET id The enclosed cavity bracket is fitted before installation in order to conceal the gap at the top of the cavity left after installation Ensure the cavity panel bracket is positioned so that the F arrow is pointing towards the front of the chassis Firmly push the bracket so that the prongs engage with the top tabs and it clicks into place Important Ensure the prongs have not been driven down into the chassis as this will damage the lid below Ensure the top trim seal is facing forward after Q attaching the bracket NOW CHOOSE WHICH INSTALLATION METHOD a or b IS MORE SUITABLE FOR YOUR CABINETRY RECOMMENDED METHOD a SECURE WITHOUT DRAWER REMOVAL FRAMELESS CABINETRY ONLY 9 ATTACH SIDE MOUNTING BRACKETS INTEGRATED ONLY ATTACH VENTING HOSE Clip all four side mounting brackets into their slots using a flat bladed screwdriver Ensure they re securely fitted before s
11. T WATER 25 SWITCH PRODUCT ON Tighten coupling with wrench e W Ensure the X 180 supplied e rubber washer is fitted inside the coupling 1 No leaks 2 Ensure drain hose is routed straight to joiner Remove excess drain hose material if necessary Do not shorten the inlet hose Important Ensure that drain connection will comply with local plumbing regulations FINAL CHECKLIST Ll OO Check all parts are installed Ensure product is level securely fastened to the cabinetry and opens and closes freely The drawer must be free to fully close with no resistance from the cabinetry Ensure inlet hose to water supply has supplied rubber washer fitted and that it s tightened a further half turn after seal contact Ensure any knockouts or plugs in drain connection have been drilled out and drain connection has been made The drain hose joiner must not support the weight of excess hose material Keep drain hose as fully extended as possible to prevent sagging Any excess length of drain hose should be kept on the dishwasher side of the highloop If connecting the drain hose to the sink trap ensure the Highloop is a minimum 6 150 mm higher than the drain hose joiner Ensure any packaging or tape securing the racks is removed from the drawer Turn on the power and water supplies then open the drawer You should hear a beep and see a program indicator lig
12. er side and push back to release drawer from runners m M m S g I m A INTEGRATED ONLY SECURE THE EXTERNAL VENT s After routing the vent hose Ca gt through and out the hole cutout attach and secure the vent by tightening the four Airg screws provided low Ensure the drawer is now rotated clockwise back Before refitting the drawer ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward Ensure the release tabs on both sides are reset fully INTEGRATED MODELS ONLY INSTALLING THE FRONT PANEL 18 REMOVE BRACKET FROM PRODUCT N WARNING Electrical Shock Hazard Before continuing ensure that the product is disconnected from the power supply Failure to follow this warning may result in electrical shock injury or fire WARNING Electrical Shock Hazard To ground earth the panel bracket connect the ground earth wire from the product to one of the tabs Any custom metal component e g handle that extends past the rubber seal must be grounded earthed too Failure to follow these warnings may result in electrical shock injury or fire 19 ATTACH PANEL TO PANEL BRACKET There must be at least 3 screws used each side 2 58 16mm x6 Align bottom of panel with bottom of bracket Important Ensure the rubber seal between the drawer and panel is kept in place
13. ht up on the internal control panel Check the spray arm is in place and free to rotate Add three cups of water into the drawer Press on the internal control panel until the indicator of the Rinse program lights up Close the drawer and press bil to start the program After the Rinse program has finished ensure the dishwasher has run and drained correctly Check water supply and drainage connection for leakage 27 TROUBLESHOOTING i Excessive water remaining above the filter plate after the rinse cycle Check for a kinked drain hose or blocked waste connection highloop not properly installed or drain hose not routed correctly No water supply This is displayed as a U1 fault see section If there is a fault in the User guide for how to recognise this fault on models without a display Check water is connected and turned on The dishwasher is beeping continuously There is a fault See section If there is a fault in the User guide for further information and instructions No program indicator lights up when the drawer is opened Ensure power is connected and is switched on If it is and still no indicator lights up see the Preference options section of the Quick start guide An option called Open drawer auto power on may need to be turned on Water around water supply and drainage connections Check connections existing plumbing and hoses for leaks Check rubber washer and hose clamp are
14. ice technician s travel to the location of the product SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions completely and carefully Ensure the product is not plugged in Installation of custom panels requires basic mechanical and electrical skills Installation must comply with your local building and electricity regulations Failure to install the custom panels correctly could invalidate any warranty or liability claims SAVE THESE INSTRUCTIONS PARTS SUPPLIED ALL MODELS vs Drain hose Drain hose Wire clip 1 Side mounting support 1 joiner 1 for securing bracket kit Drain hose joiner A and B 2 OPTIONAL Cavity bracket kit 1 Edge Protector 1 supplied with Tall height If th cae h e services hole is throu Designer and a metal partition the hole d Integrated models only must be protected with the Edge protector supplied to prevent damage to the power cord or hoses If the Drain hose supplied is not long enough to reach your services you must use a Drain Hose Extension Kit P N 525798 which will extend the drain hoses by 11 10 3 6m The kit is available from the nearest Fisher amp Paykel Authorized Service Center or Toll free 1 888 936 7872 www fisherpaykel com amp Clamp 1 for securing Drain hose joiner i Phillips 5 16 mm screws 7 1 38 mm bottom fixing screws amp metal washers 2 Rubber washe
15. liding product into cavity Check that the fitted elbow is rotated left or right depending on the direction of the routing then ensure the venting hose is securely attached to it u The mounting slots are in pairs one on each side diagonally across the product A bracket must match A slot and B bracket must match B slot 4a PULL THROUGH HOSES amp MOVE INTO THE CAVITY 1 Vent Hose Integrated models only vent either through same cabinet or adjacent cabinet as per step 9a or 9b As you push product in pull through hoses and cord ensuring they don t get kinked or twisted Important If product cannot be pushed in far enough pull out again and rearrange hoses and cord Do not use excessive force as doing so may squash the hoses and lead to incorrect operation INTEGRATED ONLY SECURE THE EXTERNAL VENT 1 After routing the vent hose through and out the hole cutout attach and secure the vent by tightening the four screws provided meer RE I 52 SECURE THE DRAWER 07 Open the drawer halfway ce Using a flat bladed screwdriver prize the gray Replace the gray rubber plug out rubber plug back into of the trim moulding the trim moulding and ensure the trim 97A seal is facing forward EQ Using a small Philips screwdriver screw through the trim moulding securing the side mounting bracket to the
16. n If the hole is through wood make sure its edges are smooth and rounded If the hole is through metal ensure you fit the supplied Edge Protector to prevent damage to the power cord INTEGRATED MODELS ONLY PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINET Services can be located either side of dishwasher VENT HOSE NW 02 WW LIT DRAIN HOSE INLET HOSE POWER CORD Important To prevent pooling of condensation from the vent hose a toekick height of no less than 4 100 mm is required The g 2 60 mm services hole for the hoses should be enlarged to accomodate the extra venting hose by cutting out some material Services can be located from the bottom corner either side of dishwasher max 172 38 mm 1 n A so POWERCORD VENTHOSE s If the services holes DRAIN HOSE are through metal INLET HOSE ensure you fit the supplied Edge Protector around the hole for the power min 4 100 mm ue Important To prevent pooling of condensation from the vent hose a toekick height of no less than 4 100 mm is required 11 External Venting kit 1 Shelf cutouts I max 34e 5 mm 8 16 220 mm 4 100 mm External Venting kit 1 Shelf cutouts max 34e 5 mm SU 2 38 60 mm 16 220 mm al 4 100 mm MAXIMUM DISTANCE
17. nt WIDTH OF PANEL min 2 mm min 23 74s 596 mm CC j HEIGHT OF THE PANEL Measure B and write it in the first box below then complete the equation ventilation gap HEIGHT OF PANEL min 2 mm een a Note when the top of the dishwasher has to be lower than the adjacent cabinetry the panel can be increased in height min s 2mm x 9 min ad s 4 et min e 2mm WIDTH OF PANEL Vs 2mm HEIGHT OF PANEL min 2mm ventilation gap with external venting kit installed min 2mm ventilation gap with external venting kit installed E 7 7 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION REMOVE THE DRAWER Product may move Mark chassis position on cavity Access cover To prevent kinked hoses we recommend rotating the drawer counter clockwise and resting it on its side after removal Press the release tabs in on either side and push back to release drawer from runners 7c TERMINATE THE WIRING AS SHOWN Remove knock out for cable clamp and fit a suitable cable clamp for the conduit 11 SS TS 11 S 10 9 Q Use copper conductors only LS 7b REMOVE THE ACCESS COVER amp POWER CORD c Before continuing ensure that the product is disconnected from the power supply Failure to follow this warning may result in electrical shock
18. options allow you to match dishwasher with your cabinetry or companion products min 2 13 mm clearance from a um Ve 2 mm Standard height models Tall height Classic models Tall height Designer models ae _ cupboard door L L Dishwasher Dishwasher CoolDrawer min 18 164 480 mm 412 mm Tall height Integrated models You may choose to install Tall height Integrated models into either a 18 456 mm ora 18 7 480 mm high cavity Note the minimum height of the custom drawer front panel will also be different for these two options 6 INTEGRATED MODELS ONLY CUSTOM FRONT PANEL CALCULATIONS FRONT PANEL SPECIFICATIONS 5 46 16 20 mm panel thickness Maximum weight of panel 20 Ib 9 kg Adequately sealed to withstand moisture 122 F 50 C 80 RH Because of it being a hot and wet environment generally the back and sides of the panel should be completely sealed with a waterproof vapour barrier ie polyurethane to prevent damage to the panel The back of the panel including any integrated handle should be completely flush so that the seal between the panel and the rubber trim is maintained The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry WIDTH OF THE PANEL Measure A the width between adjacent door drawer fronts and write it in the first box below then complete the equation clearance to adjacent cabinet fro
19. r for inlet hose 1 comes already fitted Moisture protection tape 1 to prevent moisture damage ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS i Panel bracket 1 Panel 6 External Venting kit 1 attached to product screws 4 PRODUCT DIMENSIONS Product dimensions inches mm overall height of product incl front panel height overall width of product overall depth of product excl handle depth of chassis to back of front panel maximum extension of drawer excl handle depth of front panel excl handle height of chassis depth of handle height of front panel height of ventilation gap below front panel Ae height from top of handle to top of front panel Tincludes Vs 2 mm high bracket slots Includes cavity bracket 4Recommended for a 6 2 mm ventilation gap below panel if cavity height is 16 4 412 mm STANDARD HEIGHT MODELS Jg a o a E 5 a e 16 410 16 8 410 23 9Ae 599 23 9Ae 599 22 eo 582 22 571 21 34 553 21 78 556 1 78 29 16 ve 410 n a 15 2 394 Va 7 n a 21 34 553 21 Ae 545 Te 18 16 amp 410 1 41 15 e 398 He 8 2 V 64 3Assuming front panel thickness of 1 18 mm 16 amp 410 23 6 599 22 571 21 34 553 21 74e 545 36 VAs 16 20 16 410 n a 16 Ve 408 min Ye 2
20. s basic mechanical and electrical skills Be sure to leave these Instructions with the Customer Installation must comply with your local building electricity and plumbing regulations At the completion of the dishwasher installation the Installer must perform the Final Checklist Remove all packaging materials supplied with the dishwasher This dishwasher is manufactured for indoor use only Ensure all water connections are turned OFF It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations The dishwasher MUST be installed to allow for future removal from the enclosure if service is required The switched power outlet must be outside the dishwasher cavity so that it is accessible after installation Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage Make sure only new hoses are used for connection supplied with the dishwasher Old hoses should not be reused Failure to install the dishwasher correctly could invalidate any warranty or liability claims If the product is installed in a motor vehicle boat or similar mobile facility you must bring the vehicle boat or mobile facility containing the product to the service shop at your expense or pay the serv
Download Pdf Manuals
Related Search